blob: 953e7311a644ba4b5ab0e20d851405642f070f3e [file] [log] [blame]
/*
* (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
* (C) Copyright 2013 Xilinx, Inc.
*
* Common configuration options for all Zynq boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_ZYNQ_COMMON_H
#define __CONFIG_ZYNQ_COMMON_H
/* CPU clock */
#ifndef CONFIG_CPU_FREQ_HZ
# define CONFIG_CPU_FREQ_HZ 800000000
#endif
/* Cache options */
#define CONFIG_SYS_L2CACHE_OFF
#ifndef CONFIG_SYS_L2CACHE_OFF
# define CONFIG_SYS_L2_PL310
# define CONFIG_SYS_PL310_BASE 0xf8f02000
#endif
#define ZYNQ_SCUTIMER_BASEADDR 0xF8F00600
#define CONFIG_SYS_TIMERBASE ZYNQ_SCUTIMER_BASEADDR
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
/* Serial drivers */
#define CONFIG_BAUDRATE 115200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
#define CONFIG_ARM_DCC
#define CONFIG_ZYNQ_SERIAL
/* Ethernet driver */
#if defined(CONFIG_ZYNQ_GEM)
# define CONFIG_MII
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_PHY_MARVELL
# define CONFIG_PHY_REALTEK
# define CONFIG_PHY_XILINX
# define CONFIG_BOOTP_SERVERIP
# define CONFIG_BOOTP_BOOTPATH
# define CONFIG_BOOTP_GATEWAY
# define CONFIG_BOOTP_HOSTNAME
# define CONFIG_BOOTP_MAY_FAIL
#endif
/* SPI */
#ifdef CONFIG_ZYNQ_SPI
#endif
/* QSPI */
#ifdef CONFIG_ZYNQ_QSPI
# define CONFIG_SF_DEFAULT_SPEED 30000000
# define CONFIG_SPI_FLASH_ISSI
#endif
/* NOR */
#ifndef CONFIG_SYS_NO_FLASH
# define CONFIG_SYS_FLASH_BASE 0xE2000000
# define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
# define CONFIG_SYS_MAX_FLASH_BANKS 1
# define CONFIG_SYS_MAX_FLASH_SECT 512
# define CONFIG_SYS_FLASH_ERASE_TOUT 1000
# define CONFIG_SYS_FLASH_WRITE_TOUT 5000
# define CONFIG_FLASH_SHOW_PROGRESS 10
# define CONFIG_SYS_FLASH_CFI
# undef CONFIG_SYS_FLASH_EMPTY_INFO
# define CONFIG_FLASH_CFI_DRIVER
# undef CONFIG_SYS_FLASH_PROTECTION
# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif
#ifdef CONFIG_NAND_ZYNQ
#define CONFIG_CMD_NAND_LOCK_UNLOCK
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_MTD_DEVICE
#endif
/* MMC */
#if defined(CONFIG_ZYNQ_SDHCI)
# define CONFIG_MMC
# define CONFIG_GENERIC_MMC
# define CONFIG_SDHCI
# define CONFIG_ZYNQ_SDHCI_MAX_FREQ 52000000
#endif
#ifdef CONFIG_USB_EHCI_ZYNQ
# define CONFIG_EHCI_IS_TDI
# define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000
# define DFU_DEFAULT_POLL_TIMEOUT 300
# define CONFIG_USB_CABLE_CHECK
# define CONFIG_CMD_THOR_DOWNLOAD
# define CONFIG_THOR_RESET_OFF
# define CONFIG_USB_FUNCTION_THOR
# define DFU_ALT_INFO_RAM \
"dfu_ram_info=" \
"set dfu_alt_info " \
"${kernel_image} ram 0x3000000 0x500000\\\\;" \
"${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
"${ramdisk_image} ram 0x2000000 0x600000\0" \
"dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
"thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
# if defined(CONFIG_ZYNQ_SDHCI)
# define DFU_ALT_INFO_MMC \
"dfu_mmc_info=" \
"set dfu_alt_info " \
"${kernel_image} fat 0 1\\\\;" \
"${devicetree_image} fat 0 1\\\\;" \
"${ramdisk_image} fat 0 1\0" \
"dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
"thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
# define DFU_ALT_INFO \
DFU_ALT_INFO_RAM \
DFU_ALT_INFO_MMC
# else
# define DFU_ALT_INFO \
DFU_ALT_INFO_RAM
# endif
#endif
#if !defined(DFU_ALT_INFO)
# define DFU_ALT_INFO
#endif
#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
# define CONFIG_SUPPORT_VFAT
# define CONFIG_FAT_WRITE
# define CONFIG_DOS_PARTITION
#endif
#if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
#define CONFIG_SYS_I2C_ZYNQ
#endif
/* I2C */
#if defined(CONFIG_SYS_I2C_ZYNQ)
# define CONFIG_SYS_I2C
# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
# define CONFIG_SYS_I2C_ZYNQ_SLAVE 0
#endif
/* EEPROM */
#ifdef CONFIG_ZYNQ_EEPROM
# define CONFIG_CMD_EEPROM
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
# define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
#endif
/* Total Size of Environment Sector */
#define CONFIG_ENV_SIZE (128 << 10)
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Environment */
#ifndef CONFIG_ENV_IS_NOWHERE
# ifndef CONFIG_SYS_NO_FLASH
/* Environment in NOR flash */
# define CONFIG_ENV_IS_IN_FLASH
# elif defined(CONFIG_ZYNQ_QSPI)
/* Environment in Serial Flash */
# define CONFIG_ENV_IS_IN_SPI_FLASH
# elif defined(CONFIG_SYS_NO_FLASH)
# define CONFIG_ENV_IS_NOWHERE
# endif
# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
# define CONFIG_ENV_OFFSET 0xE0000
#endif
/* enable preboot to be loaded before CONFIG_BOOTDELAY */
#define CONFIG_PREBOOT
/* Default environment */
#ifndef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"fit_image=fit.itb\0" \
"load_addr=0x2000000\0" \
"fit_size=0x800000\0" \
"flash_off=0x100000\0" \
"nor_flash_off=0xE2100000\0" \
"fdt_high=0x20000000\0" \
"initrd_high=0x20000000\0" \
"loadbootenv_addr=0x2000000\0" \
"bootenv=uEnv.txt\0" \
"bootenv_dev=mmc\0" \
"loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \
"importbootenv=echo Importing environment from ${bootenv_dev} ...; " \
"env import -t ${loadbootenv_addr} $filesize\0" \
"bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \
"setbootenv=if env run bootenv_existence_test; then " \
"if env run loadbootenv; then " \
"env run importbootenv; " \
"fi; " \
"fi; \0" \
"sd_loadbootenv=set bootenv_dev mmc && " \
"run setbootenv \0" \
"usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
"preboot=if test $modeboot = sdboot; then " \
"run sd_loadbootenv; " \
"echo Checking if uenvcmd is set ...; " \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...; " \
"run uenvcmd; " \
"fi; " \
"fi; \0" \
"norboot=echo Copying FIT from NOR flash to RAM... && " \
"cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
"bootm ${load_addr}\0" \
"sdboot=echo Copying FIT from SD to RAM... && " \
"load mmc 0 ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
"jtagboot=echo TFTPing FIT to RAM... && " \
"tftpboot ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
"usbboot=if usb start; then " \
"echo Copying FIT from USB to RAM... && " \
"load usb 0 ${load_addr} ${fit_image} && " \
"bootm ${load_addr}; fi\0" \
DFU_ALT_INFO
#endif
#define CONFIG_BOOTCOMMAND "run $modeboot"
#define CONFIG_SYS_LOAD_ADDR 0 /* default? */
/* Miscellaneous configurable options */
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_LONGHELP
#define CONFIG_CLOCKS
#define CONFIG_CMD_CLK
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/* Physical Memory map */
#define CONFIG_SYS_TEXT_BASE 0x4000000
#ifndef CONFIG_NR_DRAM_BANKS
# define CONFIG_NR_DRAM_BANKS 1
#endif
#define CONFIG_SYS_MEMTEST_START 0
#define CONFIG_SYS_MEMTEST_END 0x1000
#define CONFIG_SYS_MALLOC_LEN 0x1400000
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
/* Enable the PL to be downloaded */
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_ZYNQPL
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_FPGA_LOADP
#define CONFIG_CMD_FPGA_LOADBP
#define CONFIG_CMD_FPGA_LOADFS
/* FIT support */
#define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
/* FDT support */
#define CONFIG_DISPLAY_BOARDINFO_LATE
/* Extend size of kernel image for uncompression */
#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
/* Boot FreeBSD/vxWorks from an ELF image */
#define CONFIG_SYS_MMC_MAX_DEVICE 1
#define CONFIG_SYS_LDSCRIPT "arch/arm/mach-zynq/u-boot.lds"
/* Commands */
/* SPL part */
#define CONFIG_CMD_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_RAM_DEVICE
#define CONFIG_SPL_LDSCRIPT "arch/arm/mach-zynq/u-boot-spl.lds"
/* MMC support */
#ifdef CONFIG_ZYNQ_SDHCI
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#endif
/* Disable dcache for SPL just for sure */
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_DCACHE_OFF
#undef CONFIG_FPGA
#endif
/* Address in RAM where the parameters must be copied by SPL. */
#define CONFIG_SYS_SPL_ARGS_ADDR 0x10000000
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "system.dtb"
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
/* Not using MMC raw mode - just for compilation purpose */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
/* qspi mode is working fine */
#ifdef CONFIG_ZYNQ_QSPI
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
#define CONFIG_SYS_SPI_ARGS_OFFS 0x200000
#define CONFIG_SYS_SPI_ARGS_SIZE 0x80000
#define CONFIG_SYS_SPI_KERNEL_OFFS (CONFIG_SYS_SPI_ARGS_OFFS + \
CONFIG_SYS_SPI_ARGS_SIZE)
#endif
/* for booting directly linux */
/* SP location before relocation, must use scratch RAM */
#define CONFIG_SPL_TEXT_BASE 0x0
/* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
#define CONFIG_SPL_MAX_SIZE 0x30000
/* The highest 64k OCM address */
#define OCM_HIGH_ADDR 0xffff0000
/* On the top of OCM space */
#define CONFIG_SYS_SPL_MALLOC_START OCM_HIGH_ADDR
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000
/*
* SPL stack position - and stack goes down
* 0xfffffe00 is used for putting wfi loop.
* Set it up as limit for now.
*/
#define CONFIG_SPL_STACK 0xfffffe00
/* BSS setup */
#define CONFIG_SPL_BSS_START_ADDR 0x100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x100000
#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#endif /* __CONFIG_ZYNQ_COMMON_H */