| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2017, STMicroelectronics - All Rights Reserved |
| * Author(s): Patrice Chotard, <patrice.chotard@st.com> for STMicroelectronics. |
| */ |
| |
| #include <common.h> |
| #include <clk.h> |
| #include <cpu_func.h> |
| #include <dm.h> |
| #include <fdtdec.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <asm/bitops.h> |
| #include <asm/cache.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| #include <linux/libfdt.h> |
| #include <mmc.h> |
| #include <reset.h> |
| #include <asm/io.h> |
| #include <asm/gpio.h> |
| #include <linux/iopoll.h> |
| #include <watchdog.h> |
| |
| struct stm32_sdmmc2_plat { |
| struct mmc_config cfg; |
| struct mmc mmc; |
| }; |
| |
| struct stm32_sdmmc2_priv { |
| fdt_addr_t base; |
| struct clk clk; |
| struct reset_ctl reset_ctl; |
| struct gpio_desc cd_gpio; |
| u32 clk_reg_msk; |
| u32 pwr_reg_msk; |
| }; |
| |
| struct stm32_sdmmc2_ctx { |
| u32 cache_start; |
| u32 cache_end; |
| u32 data_length; |
| bool dpsm_abort; |
| }; |
| |
| /* SDMMC REGISTERS OFFSET */ |
| #define SDMMC_POWER 0x00 /* SDMMC power control */ |
| #define SDMMC_CLKCR 0x04 /* SDMMC clock control */ |
| #define SDMMC_ARG 0x08 /* SDMMC argument */ |
| #define SDMMC_CMD 0x0C /* SDMMC command */ |
| #define SDMMC_RESP1 0x14 /* SDMMC response 1 */ |
| #define SDMMC_RESP2 0x18 /* SDMMC response 2 */ |
| #define SDMMC_RESP3 0x1C /* SDMMC response 3 */ |
| #define SDMMC_RESP4 0x20 /* SDMMC response 4 */ |
| #define SDMMC_DTIMER 0x24 /* SDMMC data timer */ |
| #define SDMMC_DLEN 0x28 /* SDMMC data length */ |
| #define SDMMC_DCTRL 0x2C /* SDMMC data control */ |
| #define SDMMC_DCOUNT 0x30 /* SDMMC data counter */ |
| #define SDMMC_STA 0x34 /* SDMMC status */ |
| #define SDMMC_ICR 0x38 /* SDMMC interrupt clear */ |
| #define SDMMC_MASK 0x3C /* SDMMC mask */ |
| #define SDMMC_IDMACTRL 0x50 /* SDMMC DMA control */ |
| #define SDMMC_IDMABASE0 0x58 /* SDMMC DMA buffer 0 base address */ |
| |
| /* SDMMC_POWER register */ |
| #define SDMMC_POWER_PWRCTRL_MASK GENMASK(1, 0) |
| #define SDMMC_POWER_PWRCTRL_OFF 0 |
| #define SDMMC_POWER_PWRCTRL_CYCLE 2 |
| #define SDMMC_POWER_PWRCTRL_ON 3 |
| #define SDMMC_POWER_VSWITCH BIT(2) |
| #define SDMMC_POWER_VSWITCHEN BIT(3) |
| #define SDMMC_POWER_DIRPOL BIT(4) |
| |
| /* SDMMC_CLKCR register */ |
| #define SDMMC_CLKCR_CLKDIV GENMASK(9, 0) |
| #define SDMMC_CLKCR_CLKDIV_MAX SDMMC_CLKCR_CLKDIV |
| #define SDMMC_CLKCR_PWRSAV BIT(12) |
| #define SDMMC_CLKCR_WIDBUS_4 BIT(14) |
| #define SDMMC_CLKCR_WIDBUS_8 BIT(15) |
| #define SDMMC_CLKCR_NEGEDGE BIT(16) |
| #define SDMMC_CLKCR_HWFC_EN BIT(17) |
| #define SDMMC_CLKCR_DDR BIT(18) |
| #define SDMMC_CLKCR_BUSSPEED BIT(19) |
| #define SDMMC_CLKCR_SELCLKRX_MASK GENMASK(21, 20) |
| #define SDMMC_CLKCR_SELCLKRX_CK 0 |
| #define SDMMC_CLKCR_SELCLKRX_CKIN BIT(20) |
| #define SDMMC_CLKCR_SELCLKRX_FBCK BIT(21) |
| |
| /* SDMMC_CMD register */ |
| #define SDMMC_CMD_CMDINDEX GENMASK(5, 0) |
| #define SDMMC_CMD_CMDTRANS BIT(6) |
| #define SDMMC_CMD_CMDSTOP BIT(7) |
| #define SDMMC_CMD_WAITRESP GENMASK(9, 8) |
| #define SDMMC_CMD_WAITRESP_0 BIT(8) |
| #define SDMMC_CMD_WAITRESP_1 BIT(9) |
| #define SDMMC_CMD_WAITINT BIT(10) |
| #define SDMMC_CMD_WAITPEND BIT(11) |
| #define SDMMC_CMD_CPSMEN BIT(12) |
| #define SDMMC_CMD_DTHOLD BIT(13) |
| #define SDMMC_CMD_BOOTMODE BIT(14) |
| #define SDMMC_CMD_BOOTEN BIT(15) |
| #define SDMMC_CMD_CMDSUSPEND BIT(16) |
| |
| /* SDMMC_DCTRL register */ |
| #define SDMMC_DCTRL_DTEN BIT(0) |
| #define SDMMC_DCTRL_DTDIR BIT(1) |
| #define SDMMC_DCTRL_DTMODE GENMASK(3, 2) |
| #define SDMMC_DCTRL_DBLOCKSIZE GENMASK(7, 4) |
| #define SDMMC_DCTRL_DBLOCKSIZE_SHIFT 4 |
| #define SDMMC_DCTRL_RWSTART BIT(8) |
| #define SDMMC_DCTRL_RWSTOP BIT(9) |
| #define SDMMC_DCTRL_RWMOD BIT(10) |
| #define SDMMC_DCTRL_SDMMCEN BIT(11) |
| #define SDMMC_DCTRL_BOOTACKEN BIT(12) |
| #define SDMMC_DCTRL_FIFORST BIT(13) |
| |
| /* SDMMC_STA register */ |
| #define SDMMC_STA_CCRCFAIL BIT(0) |
| #define SDMMC_STA_DCRCFAIL BIT(1) |
| #define SDMMC_STA_CTIMEOUT BIT(2) |
| #define SDMMC_STA_DTIMEOUT BIT(3) |
| #define SDMMC_STA_TXUNDERR BIT(4) |
| #define SDMMC_STA_RXOVERR BIT(5) |
| #define SDMMC_STA_CMDREND BIT(6) |
| #define SDMMC_STA_CMDSENT BIT(7) |
| #define SDMMC_STA_DATAEND BIT(8) |
| #define SDMMC_STA_DHOLD BIT(9) |
| #define SDMMC_STA_DBCKEND BIT(10) |
| #define SDMMC_STA_DABORT BIT(11) |
| #define SDMMC_STA_DPSMACT BIT(12) |
| #define SDMMC_STA_CPSMACT BIT(13) |
| #define SDMMC_STA_TXFIFOHE BIT(14) |
| #define SDMMC_STA_RXFIFOHF BIT(15) |
| #define SDMMC_STA_TXFIFOF BIT(16) |
| #define SDMMC_STA_RXFIFOF BIT(17) |
| #define SDMMC_STA_TXFIFOE BIT(18) |
| #define SDMMC_STA_RXFIFOE BIT(19) |
| #define SDMMC_STA_BUSYD0 BIT(20) |
| #define SDMMC_STA_BUSYD0END BIT(21) |
| #define SDMMC_STA_SDMMCIT BIT(22) |
| #define SDMMC_STA_ACKFAIL BIT(23) |
| #define SDMMC_STA_ACKTIMEOUT BIT(24) |
| #define SDMMC_STA_VSWEND BIT(25) |
| #define SDMMC_STA_CKSTOP BIT(26) |
| #define SDMMC_STA_IDMATE BIT(27) |
| #define SDMMC_STA_IDMABTC BIT(28) |
| |
| /* SDMMC_ICR register */ |
| #define SDMMC_ICR_CCRCFAILC BIT(0) |
| #define SDMMC_ICR_DCRCFAILC BIT(1) |
| #define SDMMC_ICR_CTIMEOUTC BIT(2) |
| #define SDMMC_ICR_DTIMEOUTC BIT(3) |
| #define SDMMC_ICR_TXUNDERRC BIT(4) |
| #define SDMMC_ICR_RXOVERRC BIT(5) |
| #define SDMMC_ICR_CMDRENDC BIT(6) |
| #define SDMMC_ICR_CMDSENTC BIT(7) |
| #define SDMMC_ICR_DATAENDC BIT(8) |
| #define SDMMC_ICR_DHOLDC BIT(9) |
| #define SDMMC_ICR_DBCKENDC BIT(10) |
| #define SDMMC_ICR_DABORTC BIT(11) |
| #define SDMMC_ICR_BUSYD0ENDC BIT(21) |
| #define SDMMC_ICR_SDMMCITC BIT(22) |
| #define SDMMC_ICR_ACKFAILC BIT(23) |
| #define SDMMC_ICR_ACKTIMEOUTC BIT(24) |
| #define SDMMC_ICR_VSWENDC BIT(25) |
| #define SDMMC_ICR_CKSTOPC BIT(26) |
| #define SDMMC_ICR_IDMATEC BIT(27) |
| #define SDMMC_ICR_IDMABTCC BIT(28) |
| #define SDMMC_ICR_STATIC_FLAGS ((GENMASK(28, 21)) | (GENMASK(11, 0))) |
| |
| /* SDMMC_MASK register */ |
| #define SDMMC_MASK_CCRCFAILIE BIT(0) |
| #define SDMMC_MASK_DCRCFAILIE BIT(1) |
| #define SDMMC_MASK_CTIMEOUTIE BIT(2) |
| #define SDMMC_MASK_DTIMEOUTIE BIT(3) |
| #define SDMMC_MASK_TXUNDERRIE BIT(4) |
| #define SDMMC_MASK_RXOVERRIE BIT(5) |
| #define SDMMC_MASK_CMDRENDIE BIT(6) |
| #define SDMMC_MASK_CMDSENTIE BIT(7) |
| #define SDMMC_MASK_DATAENDIE BIT(8) |
| #define SDMMC_MASK_DHOLDIE BIT(9) |
| #define SDMMC_MASK_DBCKENDIE BIT(10) |
| #define SDMMC_MASK_DABORTIE BIT(11) |
| #define SDMMC_MASK_TXFIFOHEIE BIT(14) |
| #define SDMMC_MASK_RXFIFOHFIE BIT(15) |
| #define SDMMC_MASK_RXFIFOFIE BIT(17) |
| #define SDMMC_MASK_TXFIFOEIE BIT(18) |
| #define SDMMC_MASK_BUSYD0ENDIE BIT(21) |
| #define SDMMC_MASK_SDMMCITIE BIT(22) |
| #define SDMMC_MASK_ACKFAILIE BIT(23) |
| #define SDMMC_MASK_ACKTIMEOUTIE BIT(24) |
| #define SDMMC_MASK_VSWENDIE BIT(25) |
| #define SDMMC_MASK_CKSTOPIE BIT(26) |
| #define SDMMC_MASK_IDMABTCIE BIT(28) |
| |
| /* SDMMC_IDMACTRL register */ |
| #define SDMMC_IDMACTRL_IDMAEN BIT(0) |
| |
| #define SDMMC_CMD_TIMEOUT 0xFFFFFFFF |
| #define SDMMC_BUSYD0END_TIMEOUT_US 2000000 |
| |
| static void stm32_sdmmc2_start_data(struct stm32_sdmmc2_priv *priv, |
| struct mmc_data *data, |
| struct stm32_sdmmc2_ctx *ctx) |
| { |
| u32 data_ctrl, idmabase0; |
| |
| /* Configure the SDMMC DPSM (Data Path State Machine) */ |
| data_ctrl = (__ilog2(data->blocksize) << |
| SDMMC_DCTRL_DBLOCKSIZE_SHIFT) & |
| SDMMC_DCTRL_DBLOCKSIZE; |
| |
| if (data->flags & MMC_DATA_READ) { |
| data_ctrl |= SDMMC_DCTRL_DTDIR; |
| idmabase0 = (u32)data->dest; |
| } else { |
| idmabase0 = (u32)data->src; |
| } |
| |
| /* Set the SDMMC DataLength value */ |
| writel(ctx->data_length, priv->base + SDMMC_DLEN); |
| |
| /* Write to SDMMC DCTRL */ |
| writel(data_ctrl, priv->base + SDMMC_DCTRL); |
| |
| /* Cache align */ |
| ctx->cache_start = rounddown(idmabase0, ARCH_DMA_MINALIGN); |
| ctx->cache_end = roundup(idmabase0 + ctx->data_length, |
| ARCH_DMA_MINALIGN); |
| |
| /* |
| * Flush data cache before DMA start (clean and invalidate) |
| * Clean also needed for read |
| * Avoid issue on buffer not cached-aligned |
| */ |
| flush_dcache_range(ctx->cache_start, ctx->cache_end); |
| |
| /* Enable internal DMA */ |
| writel(idmabase0, priv->base + SDMMC_IDMABASE0); |
| writel(SDMMC_IDMACTRL_IDMAEN, priv->base + SDMMC_IDMACTRL); |
| } |
| |
| static void stm32_sdmmc2_start_cmd(struct stm32_sdmmc2_priv *priv, |
| struct mmc_cmd *cmd, u32 cmd_param, |
| struct stm32_sdmmc2_ctx *ctx) |
| { |
| u32 timeout = 0; |
| |
| if (readl(priv->base + SDMMC_CMD) & SDMMC_CMD_CPSMEN) |
| writel(0, priv->base + SDMMC_CMD); |
| |
| cmd_param |= cmd->cmdidx | SDMMC_CMD_CPSMEN; |
| if (cmd->resp_type & MMC_RSP_PRESENT) { |
| if (cmd->resp_type & MMC_RSP_136) |
| cmd_param |= SDMMC_CMD_WAITRESP; |
| else if (cmd->resp_type & MMC_RSP_CRC) |
| cmd_param |= SDMMC_CMD_WAITRESP_0; |
| else |
| cmd_param |= SDMMC_CMD_WAITRESP_1; |
| } |
| |
| /* |
| * SDMMC_DTIME must be set in two case: |
| * - on data transfert. |
| * - on busy request. |
| * If not done or too short, the dtimeout flag occurs and DPSM stays |
| * enabled/busy and waits for abort (stop transmission cmd). |
| * Next data command is not possible whereas DPSM is activated. |
| */ |
| if (ctx->data_length) { |
| timeout = SDMMC_CMD_TIMEOUT; |
| } else { |
| writel(0, priv->base + SDMMC_DCTRL); |
| |
| if (cmd->resp_type & MMC_RSP_BUSY) |
| timeout = SDMMC_CMD_TIMEOUT; |
| } |
| |
| /* Set the SDMMC Data TimeOut value */ |
| writel(timeout, priv->base + SDMMC_DTIMER); |
| |
| /* Clear flags */ |
| writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR); |
| |
| /* Set SDMMC argument value */ |
| writel(cmd->cmdarg, priv->base + SDMMC_ARG); |
| |
| /* Set SDMMC command parameters */ |
| writel(cmd_param, priv->base + SDMMC_CMD); |
| } |
| |
| static int stm32_sdmmc2_end_cmd(struct stm32_sdmmc2_priv *priv, |
| struct mmc_cmd *cmd, |
| struct stm32_sdmmc2_ctx *ctx) |
| { |
| u32 mask = SDMMC_STA_CTIMEOUT; |
| u32 status; |
| int ret; |
| |
| if (cmd->resp_type & MMC_RSP_PRESENT) { |
| mask |= SDMMC_STA_CMDREND; |
| if (cmd->resp_type & MMC_RSP_CRC) |
| mask |= SDMMC_STA_CCRCFAIL; |
| } else { |
| mask |= SDMMC_STA_CMDSENT; |
| } |
| |
| /* Polling status register */ |
| ret = readl_poll_timeout(priv->base + SDMMC_STA, status, status & mask, |
| 10000); |
| |
| if (ret < 0) { |
| debug("%s: timeout reading SDMMC_STA register\n", __func__); |
| ctx->dpsm_abort = true; |
| return ret; |
| } |
| |
| /* Check status */ |
| if (status & SDMMC_STA_CTIMEOUT) { |
| debug("%s: error SDMMC_STA_CTIMEOUT (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -ETIMEDOUT; |
| } |
| |
| if (status & SDMMC_STA_CCRCFAIL && cmd->resp_type & MMC_RSP_CRC) { |
| debug("%s: error SDMMC_STA_CCRCFAIL (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -EILSEQ; |
| } |
| |
| if (status & SDMMC_STA_CMDREND && cmd->resp_type & MMC_RSP_PRESENT) { |
| cmd->response[0] = readl(priv->base + SDMMC_RESP1); |
| if (cmd->resp_type & MMC_RSP_136) { |
| cmd->response[1] = readl(priv->base + SDMMC_RESP2); |
| cmd->response[2] = readl(priv->base + SDMMC_RESP3); |
| cmd->response[3] = readl(priv->base + SDMMC_RESP4); |
| } |
| |
| /* Wait for BUSYD0END flag if busy status is detected */ |
| if (cmd->resp_type & MMC_RSP_BUSY && |
| status & SDMMC_STA_BUSYD0) { |
| mask = SDMMC_STA_DTIMEOUT | SDMMC_STA_BUSYD0END; |
| |
| /* Polling status register */ |
| ret = readl_poll_timeout(priv->base + SDMMC_STA, |
| status, status & mask, |
| SDMMC_BUSYD0END_TIMEOUT_US); |
| |
| if (ret < 0) { |
| debug("%s: timeout reading SDMMC_STA\n", |
| __func__); |
| ctx->dpsm_abort = true; |
| return ret; |
| } |
| |
| if (status & SDMMC_STA_DTIMEOUT) { |
| debug("%s: error SDMMC_STA_DTIMEOUT (0x%x)\n", |
| __func__, status); |
| ctx->dpsm_abort = true; |
| return -ETIMEDOUT; |
| } |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int stm32_sdmmc2_end_data(struct stm32_sdmmc2_priv *priv, |
| struct mmc_cmd *cmd, |
| struct mmc_data *data, |
| struct stm32_sdmmc2_ctx *ctx) |
| { |
| u32 mask = SDMMC_STA_DCRCFAIL | SDMMC_STA_DTIMEOUT | |
| SDMMC_STA_IDMATE | SDMMC_STA_DATAEND; |
| u32 status; |
| |
| if (data->flags & MMC_DATA_READ) |
| mask |= SDMMC_STA_RXOVERR; |
| else |
| mask |= SDMMC_STA_TXUNDERR; |
| |
| status = readl(priv->base + SDMMC_STA); |
| while (!(status & mask)) |
| status = readl(priv->base + SDMMC_STA); |
| |
| /* |
| * Need invalidate the dcache again to avoid any |
| * cache-refill during the DMA operations (pre-fetching) |
| */ |
| if (data->flags & MMC_DATA_READ) |
| invalidate_dcache_range(ctx->cache_start, ctx->cache_end); |
| |
| if (status & SDMMC_STA_DCRCFAIL) { |
| debug("%s: error SDMMC_STA_DCRCFAIL (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| if (readl(priv->base + SDMMC_DCOUNT)) |
| ctx->dpsm_abort = true; |
| return -EILSEQ; |
| } |
| |
| if (status & SDMMC_STA_DTIMEOUT) { |
| debug("%s: error SDMMC_STA_DTIMEOUT (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -ETIMEDOUT; |
| } |
| |
| if (status & SDMMC_STA_TXUNDERR) { |
| debug("%s: error SDMMC_STA_TXUNDERR (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -EIO; |
| } |
| |
| if (status & SDMMC_STA_RXOVERR) { |
| debug("%s: error SDMMC_STA_RXOVERR (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -EIO; |
| } |
| |
| if (status & SDMMC_STA_IDMATE) { |
| debug("%s: error SDMMC_STA_IDMATE (0x%x) for cmd %d\n", |
| __func__, status, cmd->cmdidx); |
| ctx->dpsm_abort = true; |
| return -EIO; |
| } |
| |
| return 0; |
| } |
| |
| static int stm32_sdmmc2_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| struct stm32_sdmmc2_priv *priv = dev_get_priv(dev); |
| struct stm32_sdmmc2_ctx ctx; |
| u32 cmdat = data ? SDMMC_CMD_CMDTRANS : 0; |
| int ret, retry = 3; |
| |
| WATCHDOG_RESET(); |
| |
| retry_cmd: |
| ctx.data_length = 0; |
| ctx.dpsm_abort = false; |
| |
| if (data) { |
| ctx.data_length = data->blocks * data->blocksize; |
| stm32_sdmmc2_start_data(priv, data, &ctx); |
| } |
| |
| stm32_sdmmc2_start_cmd(priv, cmd, cmdat, &ctx); |
| |
| debug("%s: send cmd %d data: 0x%x @ 0x%x\n", |
| __func__, cmd->cmdidx, |
| data ? ctx.data_length : 0, (unsigned int)data); |
| |
| ret = stm32_sdmmc2_end_cmd(priv, cmd, &ctx); |
| |
| if (data && !ret) |
| ret = stm32_sdmmc2_end_data(priv, cmd, data, &ctx); |
| |
| /* Clear flags */ |
| writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR); |
| if (data) |
| writel(0x0, priv->base + SDMMC_IDMACTRL); |
| |
| /* |
| * To stop Data Path State Machine, a stop_transmission command |
| * shall be send on cmd or data errors. |
| */ |
| if (ctx.dpsm_abort && (cmd->cmdidx != MMC_CMD_STOP_TRANSMISSION)) { |
| struct mmc_cmd stop_cmd; |
| |
| stop_cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION; |
| stop_cmd.cmdarg = 0; |
| stop_cmd.resp_type = MMC_RSP_R1b; |
| |
| debug("%s: send STOP command to abort dpsm treatments\n", |
| __func__); |
| |
| ctx.data_length = 0; |
| |
| stm32_sdmmc2_start_cmd(priv, &stop_cmd, |
| SDMMC_CMD_CMDSTOP, &ctx); |
| stm32_sdmmc2_end_cmd(priv, &stop_cmd, &ctx); |
| |
| writel(SDMMC_ICR_STATIC_FLAGS, priv->base + SDMMC_ICR); |
| } |
| |
| if ((ret != -ETIMEDOUT) && (ret != 0) && retry) { |
| printf("%s: cmd %d failed, retrying ...\n", |
| __func__, cmd->cmdidx); |
| retry--; |
| goto retry_cmd; |
| } |
| |
| debug("%s: end for CMD %d, ret = %d\n", __func__, cmd->cmdidx, ret); |
| |
| return ret; |
| } |
| |
| /* |
| * Reset the SDMMC with the RCC.SDMMCxRST register bit. |
| * This will reset the SDMMC to the reset state and the CPSM and DPSM |
| * to the Idle state. SDMMC is disabled, Signals Hiz. |
| */ |
| static void stm32_sdmmc2_reset(struct stm32_sdmmc2_priv *priv) |
| { |
| /* Reset */ |
| reset_assert(&priv->reset_ctl); |
| udelay(2); |
| reset_deassert(&priv->reset_ctl); |
| |
| /* init the needed SDMMC register after reset */ |
| writel(priv->pwr_reg_msk, priv->base + SDMMC_POWER); |
| } |
| |
| /* |
| * Set the SDMMC in power-cycle state. |
| * This will make that the SDMMC_D[7:0], |
| * SDMMC_CMD and SDMMC_CK are driven low, to prevent the card from being |
| * supplied through the signal lines. |
| */ |
| static void stm32_sdmmc2_pwrcycle(struct stm32_sdmmc2_priv *priv) |
| { |
| if ((readl(priv->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK) == |
| SDMMC_POWER_PWRCTRL_CYCLE) |
| return; |
| |
| stm32_sdmmc2_reset(priv); |
| } |
| |
| /* |
| * set the SDMMC state Power-on: the card is clocked |
| * manage the SDMMC state control: |
| * Reset => Power-Cycle => Power-Off => Power |
| * PWRCTRL=10 PWCTRL=00 PWCTRL=11 |
| */ |
| static void stm32_sdmmc2_pwron(struct stm32_sdmmc2_priv *priv) |
| { |
| u32 pwrctrl = |
| readl(priv->base + SDMMC_POWER) & SDMMC_POWER_PWRCTRL_MASK; |
| |
| if (pwrctrl == SDMMC_POWER_PWRCTRL_ON) |
| return; |
| |
| /* warning: same PWRCTRL value after reset and for power-off state |
| * it is the reset state here = the only managed by the driver |
| */ |
| if (pwrctrl == SDMMC_POWER_PWRCTRL_OFF) { |
| writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk, |
| priv->base + SDMMC_POWER); |
| } |
| |
| /* |
| * the remaining case is SDMMC_POWER_PWRCTRL_CYCLE |
| * switch to Power-Off state: SDMCC disable, signals drive 1 |
| */ |
| writel(SDMMC_POWER_PWRCTRL_OFF | priv->pwr_reg_msk, |
| priv->base + SDMMC_POWER); |
| |
| /* After the 1ms delay set the SDMMC to power-on */ |
| mdelay(1); |
| writel(SDMMC_POWER_PWRCTRL_ON | priv->pwr_reg_msk, |
| priv->base + SDMMC_POWER); |
| |
| /* during the first 74 SDMMC_CK cycles the SDMMC is still disabled. */ |
| } |
| |
| #define IS_RISING_EDGE(reg) (reg & SDMMC_CLKCR_NEGEDGE ? 0 : 1) |
| static int stm32_sdmmc2_set_ios(struct udevice *dev) |
| { |
| struct mmc *mmc = mmc_get_mmc_dev(dev); |
| struct stm32_sdmmc2_priv *priv = dev_get_priv(dev); |
| u32 desired = mmc->clock; |
| u32 sys_clock = clk_get_rate(&priv->clk); |
| u32 clk = 0; |
| |
| debug("%s: bus_with = %d, clock = %d\n", __func__, |
| mmc->bus_width, mmc->clock); |
| |
| if (mmc->clk_disable) |
| stm32_sdmmc2_pwrcycle(priv); |
| else |
| stm32_sdmmc2_pwron(priv); |
| |
| /* |
| * clk_div = 0 => command and data generated on SDMMCCLK falling edge |
| * clk_div > 0 and NEGEDGE = 0 => command and data generated on |
| * SDMMCCLK rising edge |
| * clk_div > 0 and NEGEDGE = 1 => command and data generated on |
| * SDMMCCLK falling edge |
| */ |
| if (desired && ((sys_clock > desired) || |
| IS_RISING_EDGE(priv->clk_reg_msk))) { |
| clk = DIV_ROUND_UP(sys_clock, 2 * desired); |
| if (clk > SDMMC_CLKCR_CLKDIV_MAX) |
| clk = SDMMC_CLKCR_CLKDIV_MAX; |
| } |
| |
| if (mmc->bus_width == 4) |
| clk |= SDMMC_CLKCR_WIDBUS_4; |
| if (mmc->bus_width == 8) |
| clk |= SDMMC_CLKCR_WIDBUS_8; |
| |
| writel(clk | priv->clk_reg_msk | SDMMC_CLKCR_HWFC_EN, |
| priv->base + SDMMC_CLKCR); |
| |
| return 0; |
| } |
| |
| static int stm32_sdmmc2_getcd(struct udevice *dev) |
| { |
| struct stm32_sdmmc2_priv *priv = dev_get_priv(dev); |
| |
| debug("stm32_sdmmc2_getcd called\n"); |
| |
| if (dm_gpio_is_valid(&priv->cd_gpio)) |
| return dm_gpio_get_value(&priv->cd_gpio); |
| |
| return 1; |
| } |
| |
| static int stm32_sdmmc2_host_power_cycle(struct udevice *dev) |
| { |
| struct stm32_sdmmc2_priv *priv = dev_get_priv(dev); |
| |
| writel(SDMMC_POWER_PWRCTRL_CYCLE | priv->pwr_reg_msk, |
| priv->base + SDMMC_POWER); |
| |
| return 0; |
| } |
| |
| static const struct dm_mmc_ops stm32_sdmmc2_ops = { |
| .send_cmd = stm32_sdmmc2_send_cmd, |
| .set_ios = stm32_sdmmc2_set_ios, |
| .get_cd = stm32_sdmmc2_getcd, |
| .host_power_cycle = stm32_sdmmc2_host_power_cycle, |
| }; |
| |
| static int stm32_sdmmc2_probe(struct udevice *dev) |
| { |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct stm32_sdmmc2_plat *plat = dev_get_platdata(dev); |
| struct stm32_sdmmc2_priv *priv = dev_get_priv(dev); |
| struct mmc_config *cfg = &plat->cfg; |
| int ret; |
| |
| priv->base = dev_read_addr(dev); |
| if (priv->base == FDT_ADDR_T_NONE) |
| return -EINVAL; |
| |
| if (dev_read_bool(dev, "st,neg-edge")) |
| priv->clk_reg_msk |= SDMMC_CLKCR_NEGEDGE; |
| if (dev_read_bool(dev, "st,sig-dir")) |
| priv->pwr_reg_msk |= SDMMC_POWER_DIRPOL; |
| if (dev_read_bool(dev, "st,use-ckin")) |
| priv->clk_reg_msk |= SDMMC_CLKCR_SELCLKRX_CKIN; |
| |
| ret = clk_get_by_index(dev, 0, &priv->clk); |
| if (ret) |
| return ret; |
| |
| ret = clk_enable(&priv->clk); |
| if (ret) |
| goto clk_free; |
| |
| ret = reset_get_by_index(dev, 0, &priv->reset_ctl); |
| if (ret) |
| goto clk_disable; |
| |
| gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, |
| GPIOD_IS_IN); |
| |
| cfg->f_min = 400000; |
| cfg->f_max = dev_read_u32_default(dev, "max-frequency", 52000000); |
| cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; |
| cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; |
| cfg->name = "STM32 SD/MMC"; |
| |
| cfg->host_caps = 0; |
| if (cfg->f_max > 25000000) |
| cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; |
| |
| switch (dev_read_u32_default(dev, "bus-width", 1)) { |
| case 8: |
| cfg->host_caps |= MMC_MODE_8BIT; |
| /* fall through */ |
| case 4: |
| cfg->host_caps |= MMC_MODE_4BIT; |
| break; |
| case 1: |
| break; |
| default: |
| pr_err("invalid \"bus-width\" property, force to 1\n"); |
| } |
| |
| upriv->mmc = &plat->mmc; |
| |
| /* SDMMC init */ |
| stm32_sdmmc2_reset(priv); |
| return 0; |
| |
| clk_disable: |
| clk_disable(&priv->clk); |
| clk_free: |
| clk_free(&priv->clk); |
| |
| return ret; |
| } |
| |
| static int stm32_sdmmc_bind(struct udevice *dev) |
| { |
| struct stm32_sdmmc2_plat *plat = dev_get_platdata(dev); |
| |
| return mmc_bind(dev, &plat->mmc, &plat->cfg); |
| } |
| |
| static const struct udevice_id stm32_sdmmc2_ids[] = { |
| { .compatible = "st,stm32-sdmmc2" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(stm32_sdmmc2) = { |
| .name = "stm32_sdmmc2", |
| .id = UCLASS_MMC, |
| .of_match = stm32_sdmmc2_ids, |
| .ops = &stm32_sdmmc2_ops, |
| .probe = stm32_sdmmc2_probe, |
| .bind = stm32_sdmmc_bind, |
| .priv_auto_alloc_size = sizeof(struct stm32_sdmmc2_priv), |
| .platdata_auto_alloc_size = sizeof(struct stm32_sdmmc2_plat), |
| }; |