| // SPDX-License-Identifier: GPL-2.0+ |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include "skeleton.dtsi" |
| |
| / { |
| model = "Aspeed BMC"; |
| compatible = "aspeed,ast2600"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| i2c6 = &i2c6; |
| i2c7 = &i2c7; |
| i2c8 = &i2c8; |
| i2c9 = &i2c9; |
| i2c10 = &i2c10; |
| i2c11 = &i2c11; |
| i2c12 = &i2c12; |
| i2c13 = &i2c13; |
| i2c14 = &i2c14; |
| i2c15 = &i2c15; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &uart6; |
| serial6 = &uart7; |
| serial7 = &uart8; |
| serial8 = &uart9; |
| serial9 = &uart10; |
| serial10 = &uart11; |
| serial11 = &uart12; |
| serial12 = &uart13; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| enable-method = "aspeed,ast2600-smp"; |
| |
| cpu@0 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0xf00>; |
| }; |
| |
| cpu@1 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0xf01>; |
| }; |
| |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gfx_memory: framebuffer { |
| size = <0x01000000>; |
| alignment = <0x01000000>; |
| compatible = "shared-dma-pool"; |
| reusable; |
| }; |
| |
| video_memory: video { |
| size = <0x04000000>; |
| alignment = <0x01000000>; |
| compatible = "shared-dma-pool"; |
| no-map; |
| }; |
| }; |
| |
| ahb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| device_type = "soc"; |
| ranges; |
| |
| gic: interrupt-controller@40461000 { |
| compatible = "arm,cortex-a7-gic"; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupt-parent = <&gic>; |
| reg = <0x40461000 0x1000>, |
| <0x40462000 0x1000>, |
| <0x40464000 0x2000>, |
| <0x40466000 0x2000>; |
| }; |
| |
| ahbc: ahbc@1e600000 { |
| compatible = "aspeed,aspeed-ahbc"; |
| reg = < 0x1e600000 0x100>; |
| }; |
| |
| pwm_tach: pwm_tach@1e610000 { |
| compatible = "aspeed,ast2600-pwm-tach", "simple-mfd", "syscon"; |
| reg = <0x1e610000 0x100>; |
| clocks = <&scu ASPEED_CLK_AHB>; |
| resets = <&rst ASPEED_RESET_PWM>; |
| |
| pwm: pwm { |
| compatible = "aspeed,ast2600-pwm"; |
| #pwm-cells = <3>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| fmc: flash-controller@1e620000 { |
| reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-fmc"; |
| status = "disabled"; |
| clocks = <&scu ASPEED_CLK_AHB>; |
| num-cs = <3>; |
| |
| flash@0 { |
| reg = <0>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| |
| flash@1 { |
| reg = <1>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| |
| flash@2 { |
| reg = <2>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi1: flash-controller@1e630000 { |
| reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-spi"; |
| clocks = <&scu ASPEED_CLK_AHB>; |
| num-cs = <2>; |
| status = "disabled"; |
| |
| flash@0 { |
| reg = <0>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| |
| flash@1 { |
| reg = <1>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| }; |
| |
| spi2: flash-controller@1e631000 { |
| reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "aspeed,ast2600-spi"; |
| clocks = <&scu ASPEED_CLK_AHB>; |
| num-cs = <3>; |
| status = "disabled"; |
| |
| flash@0 { |
| reg = <0>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| |
| flash@1 { |
| reg = <1>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| |
| flash@2 { |
| reg = <2>; |
| compatible = "jedec,spi-nor"; |
| status = "disabled"; |
| }; |
| }; |
| |
| hace: hace@1e6d0000 { |
| compatible = "aspeed,ast2600-hace"; |
| reg = <0x1e6d0000 0x200>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_YCLK>; |
| status = "disabled"; |
| }; |
| |
| acry: acry@1e6fa000 { |
| compatible = "aspeed,ast2600-acry"; |
| reg = <0x1e6fa000 0x1000>, |
| <0x1e710000 0x10000>; |
| interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_RSACLK>; |
| status = "disabled"; |
| }; |
| |
| edac: sdram@1e6e0000 { |
| compatible = "aspeed,ast2600-sdram-edac"; |
| reg = <0x1e6e0000 0x174>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| mdio: bus@1e650000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e650000 0x100>; |
| |
| mdio0: mdio@0 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0 0x8>; |
| resets = <&rst ASPEED_RESET_MII>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio1_default>; |
| status = "disabled"; |
| }; |
| |
| mdio1: mdio@8 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x8 0x8>; |
| resets = <&rst ASPEED_RESET_MII>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio2_default>; |
| status = "disabled"; |
| }; |
| |
| mdio2: mdio@10 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x10 0x8>; |
| resets = <&rst ASPEED_RESET_MII>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio3_default>; |
| status = "disabled"; |
| }; |
| |
| mdio3: mdio@18 { |
| compatible = "aspeed,ast2600-mdio"; |
| reg = <0x18 0x8>; |
| resets = <&rst ASPEED_RESET_MII>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_mdio4_default>; |
| status = "disabled"; |
| }; |
| }; |
| |
| mac0: ftgmac@1e660000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e660000 0x180>, <0x1e650000 0x4>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_MAC1CLK>; |
| status = "disabled"; |
| }; |
| |
| mac1: ftgmac@1e680000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e680000 0x180>, <0x1e650008 0x4>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_MAC2CLK>; |
| status = "disabled"; |
| }; |
| |
| mac2: ftgmac@1e670000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e670000 0x180>, <0x1e650010 0x4>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_MAC3CLK>; |
| status = "disabled"; |
| }; |
| |
| mac3: ftgmac@1e690000 { |
| compatible = "aspeed,ast2600-mac", "faraday,ftgmac100"; |
| reg = <0x1e690000 0x180>, <0x1e650018 0x4>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_MAC4CLK>; |
| status = "disabled"; |
| }; |
| |
| ehci0: usb@1e6a1000 { |
| compatible = "aspeed,aspeed-ehci", "usb-ehci"; |
| reg = <0x1e6a1000 0x100>; |
| interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_USBPORT1CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2ah_default>; |
| status = "disabled"; |
| }; |
| |
| ehci1: usb@1e6a3000 { |
| compatible = "aspeed,aspeed-ehci", "usb-ehci"; |
| reg = <0x1e6a3000 0x100>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_USBPORT2CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb2bh_default>; |
| status = "disabled"; |
| }; |
| |
| apb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| syscon: syscon@1e6e2000 { |
| compatible = "aspeed,g6-scu", "syscon", "simple-mfd"; |
| reg = <0x1e6e2000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| ranges = <0 0x1e6e2000 0x1000>; |
| |
| pinctrl: pinctrl { |
| compatible = "aspeed,g6-pinctrl"; |
| aspeed,external-nodes = <&gfx &lhc>; |
| |
| }; |
| |
| vga_scratch: scratch { |
| compatible = "aspeed,bmc-misc"; |
| }; |
| |
| scu_ic0: interrupt-controller@0 { |
| #interrupt-cells = <1>; |
| compatible = "aspeed,ast2600-scu-ic"; |
| reg = <0x560 0x10>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| }; |
| |
| scu_ic1: interrupt-controller@1 { |
| #interrupt-cells = <1>; |
| compatible = "aspeed,ast2600-scu-ic"; |
| reg = <0x570 0x10>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| }; |
| |
| }; |
| |
| smp-memram@0 { |
| compatible = "aspeed,ast2600-smpmem", "syscon"; |
| reg = <0x1e6e2180 0x40>; |
| }; |
| |
| gfx: display@1e6e6000 { |
| compatible = "aspeed,ast2500-gfx", "syscon"; |
| reg = <0x1e6e6000 0x1000>; |
| reg-io-width = <4>; |
| }; |
| |
| pcie_bridge0: pcie@1e6ed000 { |
| compatible = "aspeed,ast2600-pcie"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| reg = <0x1e6ed000 0x100>; |
| ranges = <0x81000000 0x0 0x0 0x0 0x0 0x10000>, |
| <0x82000000 0x0 0x60000000 0x60000000 0x0 0x10000000>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| resets = <&rst ASPEED_RESET_PCIE_DEV_O>; |
| cfg-handle = <&pcie_cfg0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie0rc_default>; |
| |
| status = "disabled"; |
| }; |
| |
| pcie_bridge1: pcie@1e6ed200 { |
| compatible = "aspeed,ast2600-pcie"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| reg = <0x1e6ed200 0x100>; |
| ranges = <0x81000000 0x0 0x0 0x10000 0x00 0x10000>, |
| <0x82000000 0x0 0x70000000 0x70000000 0x0 0x10000000>; |
| device_type = "pci"; |
| bus-range = <0x00 0xff>; |
| resets = <&rst ASPEED_RESET_PCIE_RC_O>; |
| cfg-handle = <&pcie_cfg1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie1rc_default>; |
| |
| status = "disabled"; |
| }; |
| |
| sdc: sdc@1e740000 { |
| compatible = "aspeed,ast2600-sd-controller"; |
| reg = <0x1e740000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e740000 0x10000>; |
| clocks = <&scu ASPEED_CLK_GATE_SDCLK>; |
| status = "disabled"; |
| |
| sdhci0: sdhci@1e740100 { |
| compatible = "aspeed,ast2600-sdhci", "sdhci"; |
| reg = <0x100 0x100>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| sdhci,auto-cmd12; |
| clocks = <&scu ASPEED_CLK_SDIO>; |
| status = "disabled"; |
| }; |
| |
| sdhci1: sdhci@1e740200 { |
| compatible = "aspeed,ast2600-sdhci", "sdhci"; |
| reg = <0x200 0x100>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| sdhci,auto-cmd12; |
| clocks = <&scu ASPEED_CLK_SDIO>; |
| status = "disabled"; |
| }; |
| }; |
| |
| emmc_controller: sdc@1e750000 { |
| compatible = "aspeed,ast2600-sd-controller"; |
| reg = <0x1e750000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e750000 0x10000>; |
| clocks = <&scu ASPEED_CLK_GATE_EMMCCLK>; |
| status = "disabled"; |
| |
| emmc: sdhci@1e750100 { |
| compatible = "aspeed,ast2600-sdhci"; |
| reg = <0x100 0x100>; |
| sdhci,auto-cmd12; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_EMMC>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_emmc_default>; |
| }; |
| }; |
| |
| h2x: h2x@1e770000 { |
| compatible = "aspeed,ast2600-h2x"; |
| reg = <0x1e770000 0x100>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_H2X>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x1e770000 0x100>; |
| |
| status = "disabled"; |
| |
| pcie_cfg0: cfg0@80 { |
| reg = <0x80 0x80>; |
| compatible = "aspeed,ast2600-pcie-cfg"; |
| }; |
| |
| pcie_cfg1: cfg1@C0 { |
| compatible = "aspeed,ast2600-pcie-cfg"; |
| reg = <0xC0 0x80>; |
| }; |
| }; |
| |
| gpio0: gpio@1e780000 { |
| compatible = "aspeed,ast2600-gpio"; |
| reg = <0x1e780000 0x1000>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| gpio-ranges = <&pinctrl 0 0 220>; |
| ngpios = <208>; |
| }; |
| |
| gpio1: gpio@1e780800 { |
| compatible = "aspeed,ast2600-gpio"; |
| reg = <0x1e780800 0x800>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| gpio-ranges = <&pinctrl 0 0 208>; |
| ngpios = <36>; |
| }; |
| |
| uart1: serial@1e783000 { |
| compatible = "ns16550a"; |
| reg = <0x1e783000 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART1CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@1e784000 { |
| compatible = "ns16550a"; |
| reg = <0x1e784000 0x1000>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART5CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| wdt1: watchdog@1e785000 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785000 0x40>; |
| status = "disabled"; |
| }; |
| |
| wdt2: watchdog@1e785040 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785040 0x40>; |
| status = "disabled"; |
| }; |
| |
| wdt3: watchdog@1e785080 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e785080 0x40>; |
| status = "disabled"; |
| }; |
| |
| wdt4: watchdog@1e7850C0 { |
| compatible = "aspeed,ast2600-wdt"; |
| reg = <0x1e7850C0 0x40>; |
| status = "disabled"; |
| }; |
| |
| lpc: lpc@1e789000 { |
| compatible = "aspeed,ast2600-lpc", "simple-mfd", "syscon"; |
| reg = <0x1e789000 0x1000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x1e789000 0x1000>; |
| |
| kcs1: kcs1@0 { |
| compatible = "aspeed,ast2600-kcs-bmc"; |
| reg = <0x0 0x80>; |
| interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| kcs_chan = <1>; |
| kcs_addr = <0xCA0>; |
| status = "disabled"; |
| }; |
| |
| kcs2: kcs2@0 { |
| compatible = "aspeed,ast2600-kcs-bmc"; |
| reg = <0x0 0x80>; |
| interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; |
| kcs_chan = <2>; |
| kcs_addr = <0xCA8>; |
| status = "disabled"; |
| }; |
| |
| kcs3: kcs3@0 { |
| compatible = "aspeed,ast2600-kcs-bmc"; |
| reg = <0x0 0x80>; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| kcs_chan = <3>; |
| kcs_addr = <0xCA2>; |
| }; |
| |
| kcs4: kcs4@0 { |
| compatible = "aspeed,ast2600-kcs-bmc"; |
| reg = <0x0 0x120>; |
| interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; |
| kcs_chan = <4>; |
| kcs_addr = <0xCA4>; |
| status = "disabled"; |
| }; |
| |
| lpc_ctrl: lpc-ctrl@80 { |
| compatible = "aspeed,ast2600-lpc-ctrl"; |
| reg = <0x80 0x80>; |
| status = "disabled"; |
| }; |
| |
| lpc_snoop: lpc-snoop@80 { |
| compatible = "aspeed,ast2600-lpc-snoop"; |
| reg = <0x80 0x80>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| lhc: lhc@a0 { |
| compatible = "aspeed,ast2600-lhc"; |
| reg = <0xa0 0x24 0xc8 0x8>; |
| }; |
| |
| lpc_reset: reset-controller@98 { |
| compatible = "aspeed,ast2600-lpc-reset"; |
| reg = <0x98 0x4>; |
| #reset-cells = <1>; |
| status = "disabled"; |
| }; |
| |
| ibt: ibt@140 { |
| compatible = "aspeed,ast2600-ibt-bmc"; |
| reg = <0x140 0x18>; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| sio_regs: regs { |
| compatible = "aspeed,bmc-misc"; |
| }; |
| |
| mbox: mbox@200 { |
| compatible = "aspeed,ast2600-mbox"; |
| reg = <0x200 0x5c>; |
| interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; |
| #mbox-cells = <1>; |
| status = "disabled"; |
| }; |
| }; |
| |
| uart2: serial@1e78d000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78d000 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART2CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@1e78e000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78e000 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART3CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@1e78f000 { |
| compatible = "ns16550a"; |
| reg = <0x1e78f000 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART4CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| i2c: bus@1e78a000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x1e78a000 0x1000>; |
| }; |
| |
| fsim0: fsi@1e79b000 { |
| compatible = "aspeed,ast2600-fsi-master", "fsi-master"; |
| reg = <0x1e79b000 0x94>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fsi1_default>; |
| clocks = <&scu ASPEED_CLK_GATE_FSICLK>; |
| status = "disabled"; |
| }; |
| |
| fsim1: fsi@1e79b100 { |
| compatible = "aspeed,ast2600-fsi-master", "fsi-master"; |
| reg = <0x1e79b100 0x94>; |
| interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fsi2_default>; |
| clocks = <&scu ASPEED_CLK_GATE_FSICLK>; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@1e790000 { |
| compatible = "ns16550a"; |
| reg = <0x1e790000 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART6CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart7: serial@1e790100 { |
| compatible = "ns16550a"; |
| reg = <0x1e790100 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART7CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart8: serial@1e790200 { |
| compatible = "ns16550a"; |
| reg = <0x1e790200 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART8CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart9: serial@1e790300 { |
| compatible = "ns16550a"; |
| reg = <0x1e790300 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART9CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart10: serial@1e790400 { |
| compatible = "ns16550a"; |
| reg = <0x1e790400 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART10CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart11: serial@1e790500 { |
| compatible = "ns16550a"; |
| reg = <0x1e790400 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART11CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart12: serial@1e790600 { |
| compatible = "ns16550a"; |
| reg = <0x1e790600 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART12CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| uart13: serial@1e790700 { |
| compatible = "ns16550a"; |
| reg = <0x1e790700 0x20>; |
| reg-shift = <2>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&scu ASPEED_CLK_GATE_UART13CLK>; |
| clock-frequency = <1846154>; |
| no-loopback-test; |
| status = "disabled"; |
| }; |
| |
| display_port: dp@1e6eb000 { |
| compatible = "aspeed,ast2600-displayport"; |
| reg = <0x1e6eb000 0x200>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_DP> ,<&rst ASPEED_RESET_DP_MCU>; |
| status = "disabled"; |
| }; |
| |
| }; |
| |
| }; |
| |
| }; |
| |
| &i2c { |
| i2cglobal: i2cg@00 { |
| compatible = "aspeed,ast2600-i2c-global"; |
| reg = <0x0 0x40>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| #if 0 |
| new-mode; |
| #endif |
| }; |
| |
| i2c0: i2c@80 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x80 0x80 0xC00 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1_default>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@100 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x100 0x80 0xC20 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2_default>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@180 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x180 0x80 0xC40 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3_default>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@200 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x200 0x40 0xC60 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c4_default>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@280 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x280 0x80 0xC80 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c5_default>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@300 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x300 0x40 0xCA0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c6_default>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@380 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x380 0x80 0xCC0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c7_default>; |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c@400 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x400 0x80 0xCE0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c8_default>; |
| status = "disabled"; |
| }; |
| |
| i2c8: i2c@480 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x480 0x80 0xD00 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c9_default>; |
| status = "disabled"; |
| }; |
| |
| i2c9: i2c@500 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x500 0x80 0xD20 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c10_default>; |
| status = "disabled"; |
| }; |
| |
| i2c10: i2c@580 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x580 0x80 0xD40 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c11_default>; |
| status = "disabled"; |
| }; |
| |
| i2c11: i2c@600 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x600 0x80 0xD60 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c12_default>; |
| status = "disabled"; |
| }; |
| |
| i2c12: i2c@680 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x680 0x80 0xD80 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c13_default>; |
| status = "disabled"; |
| }; |
| |
| i2c13: i2c@700 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x700 0x80 0xDA0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c14_default>; |
| status = "disabled"; |
| }; |
| |
| i2c14: i2c@780 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x780 0x80 0xDC0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c15_default>; |
| status = "disabled"; |
| }; |
| |
| i2c15: i2c@800 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #interrupt-cells = <1>; |
| |
| reg = <0x800 0x80 0xDE0 0x20>; |
| compatible = "aspeed,ast2600-i2c-bus"; |
| bus-frequency = <100000>; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; |
| resets = <&rst ASPEED_RESET_I2C>; |
| clocks = <&scu ASPEED_CLK_APB2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c16_default>; |
| status = "disabled"; |
| }; |
| |
| }; |
| |
| &pinctrl { |
| pinctrl_fmcquad_default: fmcquad_default { |
| function = "FMCQUAD"; |
| groups = "FMCQUAD"; |
| }; |
| |
| pinctrl_spi1_default: spi1_default { |
| function = "SPI1"; |
| groups = "SPI1"; |
| }; |
| |
| pinctrl_spi1abr_default: spi1abr_default { |
| function = "SPI1ABR"; |
| groups = "SPI1ABR"; |
| }; |
| |
| pinctrl_spi1cs1_default: spi1cs1_default { |
| function = "SPI1CS1"; |
| groups = "SPI1CS1"; |
| }; |
| |
| pinctrl_spi1wp_default: spi1wp_default { |
| function = "SPI1WP"; |
| groups = "SPI1WP"; |
| }; |
| |
| pinctrl_spi1quad_default: spi1quad_default { |
| function = "SPI1QUAD"; |
| groups = "SPI1QUAD"; |
| }; |
| |
| pinctrl_spi2_default: spi2_default { |
| function = "SPI2"; |
| groups = "SPI2"; |
| }; |
| |
| pinctrl_spi2cs1_default: spi2cs1_default { |
| function = "SPI2CS1"; |
| groups = "SPI2CS1"; |
| }; |
| |
| pinctrl_spi2cs2_default: spi2cs2_default { |
| function = "SPI2CS2"; |
| groups = "SPI2CS2"; |
| }; |
| |
| pinctrl_spi2quad_default: spi2quad_default { |
| function = "SPI2QUAD"; |
| groups = "SPI2QUAD"; |
| }; |
| |
| pinctrl_acpi_default: acpi_default { |
| function = "ACPI"; |
| groups = "ACPI"; |
| }; |
| |
| pinctrl_adc0_default: adc0_default { |
| function = "ADC0"; |
| groups = "ADC0"; |
| }; |
| |
| pinctrl_adc1_default: adc1_default { |
| function = "ADC1"; |
| groups = "ADC1"; |
| }; |
| |
| pinctrl_adc10_default: adc10_default { |
| function = "ADC10"; |
| groups = "ADC10"; |
| }; |
| |
| pinctrl_adc11_default: adc11_default { |
| function = "ADC11"; |
| groups = "ADC11"; |
| }; |
| |
| pinctrl_adc12_default: adc12_default { |
| function = "ADC12"; |
| groups = "ADC12"; |
| }; |
| |
| pinctrl_adc13_default: adc13_default { |
| function = "ADC13"; |
| groups = "ADC13"; |
| }; |
| |
| pinctrl_adc14_default: adc14_default { |
| function = "ADC14"; |
| groups = "ADC14"; |
| }; |
| |
| pinctrl_adc15_default: adc15_default { |
| function = "ADC15"; |
| groups = "ADC15"; |
| }; |
| |
| pinctrl_adc2_default: adc2_default { |
| function = "ADC2"; |
| groups = "ADC2"; |
| }; |
| |
| pinctrl_adc3_default: adc3_default { |
| function = "ADC3"; |
| groups = "ADC3"; |
| }; |
| |
| pinctrl_adc4_default: adc4_default { |
| function = "ADC4"; |
| groups = "ADC4"; |
| }; |
| |
| pinctrl_adc5_default: adc5_default { |
| function = "ADC5"; |
| groups = "ADC5"; |
| }; |
| |
| pinctrl_adc6_default: adc6_default { |
| function = "ADC6"; |
| groups = "ADC6"; |
| }; |
| |
| pinctrl_adc7_default: adc7_default { |
| function = "ADC7"; |
| groups = "ADC7"; |
| }; |
| |
| pinctrl_adc8_default: adc8_default { |
| function = "ADC8"; |
| groups = "ADC8"; |
| }; |
| |
| pinctrl_adc9_default: adc9_default { |
| function = "ADC9"; |
| groups = "ADC9"; |
| }; |
| |
| pinctrl_bmcint_default: bmcint_default { |
| function = "BMCINT"; |
| groups = "BMCINT"; |
| }; |
| |
| pinctrl_ddcclk_default: ddcclk_default { |
| function = "DDCCLK"; |
| groups = "DDCCLK"; |
| }; |
| |
| pinctrl_ddcdat_default: ddcdat_default { |
| function = "DDCDAT"; |
| groups = "DDCDAT"; |
| }; |
| |
| pinctrl_espi_default: espi_default { |
| function = "ESPI"; |
| groups = "ESPI"; |
| }; |
| |
| pinctrl_fsi1_default: fsi1_default { |
| function = "FSI1"; |
| groups = "FSI1"; |
| }; |
| |
| pinctrl_fsi2_default: fsi2_default { |
| function = "FSI2"; |
| groups = "FSI2"; |
| }; |
| |
| pinctrl_fwspics1_default: fwspics1_default { |
| function = "FWSPICS1"; |
| groups = "FWSPICS1"; |
| }; |
| |
| pinctrl_fwspics2_default: fwspics2_default { |
| function = "FWSPICS2"; |
| groups = "FWSPICS2"; |
| }; |
| |
| pinctrl_gpid0_default: gpid0_default { |
| function = "GPID0"; |
| groups = "GPID0"; |
| }; |
| |
| pinctrl_gpid2_default: gpid2_default { |
| function = "GPID2"; |
| groups = "GPID2"; |
| }; |
| |
| pinctrl_gpid4_default: gpid4_default { |
| function = "GPID4"; |
| groups = "GPID4"; |
| }; |
| |
| pinctrl_gpid6_default: gpid6_default { |
| function = "GPID6"; |
| groups = "GPID6"; |
| }; |
| |
| pinctrl_gpie0_default: gpie0_default { |
| function = "GPIE0"; |
| groups = "GPIE0"; |
| }; |
| |
| pinctrl_gpie2_default: gpie2_default { |
| function = "GPIE2"; |
| groups = "GPIE2"; |
| }; |
| |
| pinctrl_gpie4_default: gpie4_default { |
| function = "GPIE4"; |
| groups = "GPIE4"; |
| }; |
| |
| pinctrl_gpie6_default: gpie6_default { |
| function = "GPIE6"; |
| groups = "GPIE6"; |
| }; |
| |
| pinctrl_i2c1_default: i2c1_default { |
| function = "I2C1"; |
| groups = "I2C1"; |
| }; |
| |
| pinctrl_i2c2_default: i2c2_default { |
| function = "I2C2"; |
| groups = "I2C2"; |
| }; |
| |
| pinctrl_i2c3_default: i2c3_default { |
| function = "I2C3"; |
| groups = "I2C3"; |
| }; |
| |
| pinctrl_i2c4_default: i2c4_default { |
| function = "I2C4"; |
| groups = "I2C4"; |
| }; |
| |
| pinctrl_i2c5_default: i2c5_default { |
| function = "I2C5"; |
| groups = "I2C5"; |
| }; |
| |
| pinctrl_i2c6_default: i2c6_default { |
| function = "I2C6"; |
| groups = "I2C6"; |
| }; |
| |
| pinctrl_i2c7_default: i2c7_default { |
| function = "I2C7"; |
| groups = "I2C7"; |
| }; |
| |
| pinctrl_i2c8_default: i2c8_default { |
| function = "I2C8"; |
| groups = "I2C8"; |
| }; |
| |
| pinctrl_i2c9_default: i2c9_default { |
| function = "I2C9"; |
| groups = "I2C9"; |
| }; |
| |
| pinctrl_i2c10_default: i2c10_default { |
| function = "I2C10"; |
| groups = "I2C10"; |
| }; |
| |
| pinctrl_i2c11_default: i2c11_default { |
| function = "I2C11"; |
| groups = "I2C11"; |
| }; |
| |
| pinctrl_i2c12_default: i2c12_default { |
| function = "I2C12"; |
| groups = "I2C12"; |
| }; |
| |
| pinctrl_i2c13_default: i2c13_default { |
| function = "I2C13"; |
| groups = "I2C13"; |
| }; |
| |
| pinctrl_i2c14_default: i2c14_default { |
| function = "I2C14"; |
| groups = "I2C14"; |
| }; |
| |
| pinctrl_i2c15_default: i2c15_default { |
| function = "I2C15"; |
| groups = "I2C15"; |
| }; |
| |
| pinctrl_i2c16_default: i2c16_default { |
| function = "I2C16"; |
| groups = "I2C16"; |
| }; |
| |
| pinctrl_lad0_default: lad0_default { |
| function = "LAD0"; |
| groups = "LAD0"; |
| }; |
| |
| pinctrl_lad1_default: lad1_default { |
| function = "LAD1"; |
| groups = "LAD1"; |
| }; |
| |
| pinctrl_lad2_default: lad2_default { |
| function = "LAD2"; |
| groups = "LAD2"; |
| }; |
| |
| pinctrl_lad3_default: lad3_default { |
| function = "LAD3"; |
| groups = "LAD3"; |
| }; |
| |
| pinctrl_lclk_default: lclk_default { |
| function = "LCLK"; |
| groups = "LCLK"; |
| }; |
| |
| pinctrl_lframe_default: lframe_default { |
| function = "LFRAME"; |
| groups = "LFRAME"; |
| }; |
| |
| pinctrl_lpchc_default: lpchc_default { |
| function = "LPCHC"; |
| groups = "LPCHC"; |
| }; |
| |
| pinctrl_lpcpd_default: lpcpd_default { |
| function = "LPCPD"; |
| groups = "LPCPD"; |
| }; |
| |
| pinctrl_lpcplus_default: lpcplus_default { |
| function = "LPCPLUS"; |
| groups = "LPCPLUS"; |
| }; |
| |
| pinctrl_lpcpme_default: lpcpme_default { |
| function = "LPCPME"; |
| groups = "LPCPME"; |
| }; |
| |
| pinctrl_lpcrst_default: lpcrst_default { |
| function = "LPCRST"; |
| groups = "LPCRST"; |
| }; |
| |
| pinctrl_lpcsmi_default: lpcsmi_default { |
| function = "LPCSMI"; |
| groups = "LPCSMI"; |
| }; |
| |
| pinctrl_lsirq_default: lsirq_default { |
| function = "LSIRQ"; |
| groups = "LSIRQ"; |
| }; |
| |
| pinctrl_mac1link_default: mac1link_default { |
| function = "MAC1LINK"; |
| groups = "MAC1LINK"; |
| }; |
| |
| pinctrl_mac2link_default: mac2link_default { |
| function = "MAC2LINK"; |
| groups = "MAC2LINK"; |
| }; |
| |
| pinctrl_mac3link_default: mac3link_default { |
| function = "MAC3LINK"; |
| groups = "MAC3LINK"; |
| }; |
| |
| pinctrl_mac4link_default: mac4link_default { |
| function = "MAC4LINK"; |
| groups = "MAC4LINK"; |
| }; |
| |
| pinctrl_mdio1_default: mdio1_default { |
| function = "MDIO1"; |
| groups = "MDIO1"; |
| }; |
| |
| pinctrl_mdio2_default: mdio2_default { |
| function = "MDIO2"; |
| groups = "MDIO2"; |
| }; |
| |
| pinctrl_mdio3_default: mdio3_default { |
| function = "MDIO3"; |
| groups = "MDIO3"; |
| }; |
| |
| pinctrl_mdio4_default: mdio4_default { |
| function = "MDIO4"; |
| groups = "MDIO4"; |
| }; |
| |
| pinctrl_rmii1_default: rmii1_default { |
| function = "RMII1"; |
| groups = "RMII1"; |
| }; |
| |
| pinctrl_rmii2_default: rmii2_default { |
| function = "RMII2"; |
| groups = "RMII2"; |
| }; |
| |
| pinctrl_rmii3_default: rmii3_default { |
| function = "RMII3"; |
| groups = "RMII3"; |
| }; |
| |
| pinctrl_rmii4_default: rmii4_default { |
| function = "RMII4"; |
| groups = "RMII4"; |
| }; |
| |
| pinctrl_rmii1rclk_default: rmii1rclk_default { |
| function = "RMII1RCLK"; |
| groups = "RMII1RCLK"; |
| }; |
| |
| pinctrl_rmii2rclk_default: rmii2rclk_default { |
| function = "RMII2RCLK"; |
| groups = "RMII2RCLK"; |
| }; |
| |
| pinctrl_rmii3rclk_default: rmii3rclk_default { |
| function = "RMII3RCLK"; |
| groups = "RMII3RCLK"; |
| }; |
| |
| pinctrl_rmii4rclk_default: rmii4rclk_default { |
| function = "RMII4RCLK"; |
| groups = "RMII4RCLK"; |
| }; |
| |
| pinctrl_ncts1_default: ncts1_default { |
| function = "NCTS1"; |
| groups = "NCTS1"; |
| }; |
| |
| pinctrl_ncts2_default: ncts2_default { |
| function = "NCTS2"; |
| groups = "NCTS2"; |
| }; |
| |
| pinctrl_ncts3_default: ncts3_default { |
| function = "NCTS3"; |
| groups = "NCTS3"; |
| }; |
| |
| pinctrl_ncts4_default: ncts4_default { |
| function = "NCTS4"; |
| groups = "NCTS4"; |
| }; |
| |
| pinctrl_ndcd1_default: ndcd1_default { |
| function = "NDCD1"; |
| groups = "NDCD1"; |
| }; |
| |
| pinctrl_ndcd2_default: ndcd2_default { |
| function = "NDCD2"; |
| groups = "NDCD2"; |
| }; |
| |
| pinctrl_ndcd3_default: ndcd3_default { |
| function = "NDCD3"; |
| groups = "NDCD3"; |
| }; |
| |
| pinctrl_ndcd4_default: ndcd4_default { |
| function = "NDCD4"; |
| groups = "NDCD4"; |
| }; |
| |
| pinctrl_ndsr1_default: ndsr1_default { |
| function = "NDSR1"; |
| groups = "NDSR1"; |
| }; |
| |
| pinctrl_ndsr2_default: ndsr2_default { |
| function = "NDSR2"; |
| groups = "NDSR2"; |
| }; |
| |
| pinctrl_ndsr3_default: ndsr3_default { |
| function = "NDSR3"; |
| groups = "NDSR3"; |
| }; |
| |
| pinctrl_ndsr4_default: ndsr4_default { |
| function = "NDSR4"; |
| groups = "NDSR4"; |
| }; |
| |
| pinctrl_ndtr1_default: ndtr1_default { |
| function = "NDTR1"; |
| groups = "NDTR1"; |
| }; |
| |
| pinctrl_ndtr2_default: ndtr2_default { |
| function = "NDTR2"; |
| groups = "NDTR2"; |
| }; |
| |
| pinctrl_ndtr3_default: ndtr3_default { |
| function = "NDTR3"; |
| groups = "NDTR3"; |
| }; |
| |
| pinctrl_ndtr4_default: ndtr4_default { |
| function = "NDTR4"; |
| groups = "NDTR4"; |
| }; |
| |
| pinctrl_nri1_default: nri1_default { |
| function = "NRI1"; |
| groups = "NRI1"; |
| }; |
| |
| pinctrl_nri2_default: nri2_default { |
| function = "NRI2"; |
| groups = "NRI2"; |
| }; |
| |
| pinctrl_nri3_default: nri3_default { |
| function = "NRI3"; |
| groups = "NRI3"; |
| }; |
| |
| pinctrl_nri4_default: nri4_default { |
| function = "NRI4"; |
| groups = "NRI4"; |
| }; |
| |
| pinctrl_nrts1_default: nrts1_default { |
| function = "NRTS1"; |
| groups = "NRTS1"; |
| }; |
| |
| pinctrl_nrts2_default: nrts2_default { |
| function = "NRTS2"; |
| groups = "NRTS2"; |
| }; |
| |
| pinctrl_nrts3_default: nrts3_default { |
| function = "NRTS3"; |
| groups = "NRTS3"; |
| }; |
| |
| pinctrl_nrts4_default: nrts4_default { |
| function = "NRTS4"; |
| groups = "NRTS4"; |
| }; |
| |
| pinctrl_oscclk_default: oscclk_default { |
| function = "OSCCLK"; |
| groups = "OSCCLK"; |
| }; |
| |
| pinctrl_pewake_default: pewake_default { |
| function = "PEWAKE"; |
| groups = "PEWAKE"; |
| }; |
| |
| pinctrl_pnor_default: pnor_default { |
| function = "PNOR"; |
| groups = "PNOR"; |
| }; |
| |
| pinctrl_pwm0_default: pwm0_default { |
| function = "PWM0"; |
| groups = "PWM0"; |
| }; |
| |
| pinctrl_pwm1_default: pwm1_default { |
| function = "PWM1"; |
| groups = "PWM1"; |
| }; |
| |
| pinctrl_pwm2_default: pwm2_default { |
| function = "PWM2"; |
| groups = "PWM2"; |
| }; |
| |
| pinctrl_pwm3_default: pwm3_default { |
| function = "PWM3"; |
| groups = "PWM3"; |
| }; |
| |
| pinctrl_pwm4_default: pwm4_default { |
| function = "PWM4"; |
| groups = "PWM4"; |
| }; |
| |
| pinctrl_pwm5_default: pwm5_default { |
| function = "PWM5"; |
| groups = "PWM5"; |
| }; |
| |
| pinctrl_pwm6_default: pwm6_default { |
| function = "PWM6"; |
| groups = "PWM6"; |
| }; |
| |
| pinctrl_pwm7_default: pwm7_default { |
| function = "PWM7"; |
| groups = "PWM7"; |
| }; |
| |
| pinctrl_pwm8g0_default: pwm8g0_default { |
| function = "PWM8G0"; |
| groups = "PWM8G0"; |
| }; |
| |
| pinctrl_pwm8g1_default: pwm8g1_default { |
| function = "PWM8G1"; |
| groups = "PWM8G1"; |
| }; |
| |
| pinctrl_pwm9g0_default: pwm9g0_default { |
| function = "PWM9G0"; |
| groups = "PWM9G0"; |
| }; |
| |
| pinctrl_pwm9g1_default: pwm9g1_default { |
| function = "PWM9G1"; |
| groups = "PWM9G1"; |
| }; |
| |
| pinctrl_pwm10g0_default: pwm10g0_default { |
| function = "PWM10G0"; |
| groups = "PWM10G0"; |
| }; |
| |
| pinctrl_pwm10g1_default: pwm10g1_default { |
| function = "PWM10G1"; |
| groups = "PWM10G1"; |
| }; |
| |
| pinctrl_pwm11g0_default: pwm11g0_default { |
| function = "PWM11G0"; |
| groups = "PWM11G0"; |
| }; |
| |
| pinctrl_pwm11g1_default: pwm11g1_default { |
| function = "PWM11G1"; |
| groups = "PWM11G1"; |
| }; |
| |
| pinctrl_pwm12g0_default: pwm12g0_default { |
| function = "PWM12G0"; |
| groups = "PWM12G0"; |
| }; |
| |
| pinctrl_pwm12g1_default: pwm12g1_default { |
| function = "PWM12G1"; |
| groups = "PWM12G1"; |
| }; |
| |
| pinctrl_pwm13g0_default: pwm13g0_default { |
| function = "PWM13G0"; |
| groups = "PWM13G0"; |
| }; |
| |
| pinctrl_pwm13g1_default: pwm13g1_default { |
| function = "PWM13G1"; |
| groups = "PWM13G1"; |
| }; |
| |
| pinctrl_pwm14g0_default: pwm14g0_default { |
| function = "PWM14G0"; |
| groups = "PWM14G0"; |
| }; |
| |
| pinctrl_pwm14g1_default: pwm14g1_default { |
| function = "PWM14G1"; |
| groups = "PWM14G1"; |
| }; |
| |
| pinctrl_pwm15g0_default: pwm15g0_default { |
| function = "PWM15G0"; |
| groups = "PWM15G0"; |
| }; |
| |
| pinctrl_pwm15g1_default: pwm15g1_default { |
| function = "PWM15G1"; |
| groups = "PWM15G1"; |
| }; |
| |
| pinctrl_rgmii1_default: rgmii1_default { |
| function = "RGMII1"; |
| groups = "RGMII1"; |
| }; |
| |
| pinctrl_rgmii2_default: rgmii2_default { |
| function = "RGMII2"; |
| groups = "RGMII2"; |
| }; |
| |
| pinctrl_rgmii3_default: rgmii3_default { |
| function = "RGMII3"; |
| groups = "RGMII3"; |
| }; |
| |
| pinctrl_rgmii4_default: rgmii4_default { |
| function = "RGMII4"; |
| groups = "RGMII4"; |
| }; |
| |
| pinctrl_rmii1_default: rmii1_default { |
| function = "RMII1"; |
| groups = "RMII1"; |
| }; |
| |
| pinctrl_rmii2_default: rmii2_default { |
| function = "RMII2"; |
| groups = "RMII2"; |
| }; |
| |
| pinctrl_rxd1_default: rxd1_default { |
| function = "RXD1"; |
| groups = "RXD1"; |
| }; |
| |
| pinctrl_rxd2_default: rxd2_default { |
| function = "RXD2"; |
| groups = "RXD2"; |
| }; |
| |
| pinctrl_rxd3_default: rxd3_default { |
| function = "RXD3"; |
| groups = "RXD3"; |
| }; |
| |
| pinctrl_rxd4_default: rxd4_default { |
| function = "RXD4"; |
| groups = "RXD4"; |
| }; |
| |
| pinctrl_salt1_default: salt1_default { |
| function = "SALT1"; |
| groups = "SALT1"; |
| }; |
| |
| pinctrl_salt10_default: salt10_default { |
| function = "SALT10"; |
| groups = "SALT10"; |
| }; |
| |
| pinctrl_salt11_default: salt11_default { |
| function = "SALT11"; |
| groups = "SALT11"; |
| }; |
| |
| pinctrl_salt12_default: salt12_default { |
| function = "SALT12"; |
| groups = "SALT12"; |
| }; |
| |
| pinctrl_salt13_default: salt13_default { |
| function = "SALT13"; |
| groups = "SALT13"; |
| }; |
| |
| pinctrl_salt14_default: salt14_default { |
| function = "SALT14"; |
| groups = "SALT14"; |
| }; |
| |
| pinctrl_salt2_default: salt2_default { |
| function = "SALT2"; |
| groups = "SALT2"; |
| }; |
| |
| pinctrl_salt3_default: salt3_default { |
| function = "SALT3"; |
| groups = "SALT3"; |
| }; |
| |
| pinctrl_salt4_default: salt4_default { |
| function = "SALT4"; |
| groups = "SALT4"; |
| }; |
| |
| pinctrl_salt5_default: salt5_default { |
| function = "SALT5"; |
| groups = "SALT5"; |
| }; |
| |
| pinctrl_salt6_default: salt6_default { |
| function = "SALT6"; |
| groups = "SALT6"; |
| }; |
| |
| pinctrl_salt7_default: salt7_default { |
| function = "SALT7"; |
| groups = "SALT7"; |
| }; |
| |
| pinctrl_salt8_default: salt8_default { |
| function = "SALT8"; |
| groups = "SALT8"; |
| }; |
| |
| pinctrl_salt9_default: salt9_default { |
| function = "SALT9"; |
| groups = "SALT9"; |
| }; |
| |
| pinctrl_scl1_default: scl1_default { |
| function = "SCL1"; |
| groups = "SCL1"; |
| }; |
| |
| pinctrl_scl2_default: scl2_default { |
| function = "SCL2"; |
| groups = "SCL2"; |
| }; |
| |
| pinctrl_sd1_default: sd1_default { |
| function = "SD1"; |
| groups = "SD1"; |
| }; |
| |
| pinctrl_sd2_default: sd2_default { |
| function = "SD2"; |
| groups = "SD2"; |
| }; |
| |
| pinctrl_emmc_default: emmc_default { |
| function = "EMMC"; |
| groups = "EMMC"; |
| }; |
| |
| pinctrl_emmcg8_default: emmcg8_default { |
| function = "EMMCG8"; |
| groups = "EMMCG8"; |
| }; |
| |
| pinctrl_sda1_default: sda1_default { |
| function = "SDA1"; |
| groups = "SDA1"; |
| }; |
| |
| pinctrl_sda2_default: sda2_default { |
| function = "SDA2"; |
| groups = "SDA2"; |
| }; |
| |
| pinctrl_sgps1_default: sgps1_default { |
| function = "SGPS1"; |
| groups = "SGPS1"; |
| }; |
| |
| pinctrl_sgps2_default: sgps2_default { |
| function = "SGPS2"; |
| groups = "SGPS2"; |
| }; |
| |
| pinctrl_sioonctrl_default: sioonctrl_default { |
| function = "SIOONCTRL"; |
| groups = "SIOONCTRL"; |
| }; |
| |
| pinctrl_siopbi_default: siopbi_default { |
| function = "SIOPBI"; |
| groups = "SIOPBI"; |
| }; |
| |
| pinctrl_siopbo_default: siopbo_default { |
| function = "SIOPBO"; |
| groups = "SIOPBO"; |
| }; |
| |
| pinctrl_siopwreq_default: siopwreq_default { |
| function = "SIOPWREQ"; |
| groups = "SIOPWREQ"; |
| }; |
| |
| pinctrl_siopwrgd_default: siopwrgd_default { |
| function = "SIOPWRGD"; |
| groups = "SIOPWRGD"; |
| }; |
| |
| pinctrl_sios3_default: sios3_default { |
| function = "SIOS3"; |
| groups = "SIOS3"; |
| }; |
| |
| pinctrl_sios5_default: sios5_default { |
| function = "SIOS5"; |
| groups = "SIOS5"; |
| }; |
| |
| pinctrl_siosci_default: siosci_default { |
| function = "SIOSCI"; |
| groups = "SIOSCI"; |
| }; |
| |
| pinctrl_spi1_default: spi1_default { |
| function = "SPI1"; |
| groups = "SPI1"; |
| }; |
| |
| pinctrl_spi1cs1_default: spi1cs1_default { |
| function = "SPI1CS1"; |
| groups = "SPI1CS1"; |
| }; |
| |
| pinctrl_spi1debug_default: spi1debug_default { |
| function = "SPI1DEBUG"; |
| groups = "SPI1DEBUG"; |
| }; |
| |
| pinctrl_spi1passthru_default: spi1passthru_default { |
| function = "SPI1PASSTHRU"; |
| groups = "SPI1PASSTHRU"; |
| }; |
| |
| pinctrl_spi2ck_default: spi2ck_default { |
| function = "SPI2CK"; |
| groups = "SPI2CK"; |
| }; |
| |
| pinctrl_spi2cs0_default: spi2cs0_default { |
| function = "SPI2CS0"; |
| groups = "SPI2CS0"; |
| }; |
| |
| pinctrl_spi2cs1_default: spi2cs1_default { |
| function = "SPI2CS1"; |
| groups = "SPI2CS1"; |
| }; |
| |
| pinctrl_spi2miso_default: spi2miso_default { |
| function = "SPI2MISO"; |
| groups = "SPI2MISO"; |
| }; |
| |
| pinctrl_spi2mosi_default: spi2mosi_default { |
| function = "SPI2MOSI"; |
| groups = "SPI2MOSI"; |
| }; |
| |
| pinctrl_timer3_default: timer3_default { |
| function = "TIMER3"; |
| groups = "TIMER3"; |
| }; |
| |
| pinctrl_timer4_default: timer4_default { |
| function = "TIMER4"; |
| groups = "TIMER4"; |
| }; |
| |
| pinctrl_timer5_default: timer5_default { |
| function = "TIMER5"; |
| groups = "TIMER5"; |
| }; |
| |
| pinctrl_timer6_default: timer6_default { |
| function = "TIMER6"; |
| groups = "TIMER6"; |
| }; |
| |
| pinctrl_timer7_default: timer7_default { |
| function = "TIMER7"; |
| groups = "TIMER7"; |
| }; |
| |
| pinctrl_timer8_default: timer8_default { |
| function = "TIMER8"; |
| groups = "TIMER8"; |
| }; |
| |
| pinctrl_txd1_default: txd1_default { |
| function = "TXD1"; |
| groups = "TXD1"; |
| }; |
| |
| pinctrl_txd2_default: txd2_default { |
| function = "TXD2"; |
| groups = "TXD2"; |
| }; |
| |
| pinctrl_txd3_default: txd3_default { |
| function = "TXD3"; |
| groups = "TXD3"; |
| }; |
| |
| pinctrl_txd4_default: txd4_default { |
| function = "TXD4"; |
| groups = "TXD4"; |
| }; |
| |
| pinctrl_uart6_default: uart6_default { |
| function = "UART6"; |
| groups = "UART6"; |
| }; |
| |
| pinctrl_usbcki_default: usbcki_default { |
| function = "USBCKI"; |
| groups = "USBCKI"; |
| }; |
| |
| pinctrl_usb2ah_default: usb2ah_default { |
| function = "USB2AH"; |
| groups = "USB2AH"; |
| }; |
| |
| pinctrl_usb11bhid_default: usb11bhid_default { |
| function = "USB11BHID"; |
| groups = "USB11BHID"; |
| }; |
| |
| pinctrl_usb2bh_default: usb2bh_default { |
| function = "USB2BH"; |
| groups = "USB2BH"; |
| }; |
| |
| pinctrl_vgabiosrom_default: vgabiosrom_default { |
| function = "VGABIOSROM"; |
| groups = "VGABIOSROM"; |
| }; |
| |
| pinctrl_vgahs_default: vgahs_default { |
| function = "VGAHS"; |
| groups = "VGAHS"; |
| }; |
| |
| pinctrl_vgavs_default: vgavs_default { |
| function = "VGAVS"; |
| groups = "VGAVS"; |
| }; |
| |
| pinctrl_vpi24_default: vpi24_default { |
| function = "VPI24"; |
| groups = "VPI24"; |
| }; |
| |
| pinctrl_vpo_default: vpo_default { |
| function = "VPO"; |
| groups = "VPO"; |
| }; |
| |
| pinctrl_wdtrst1_default: wdtrst1_default { |
| function = "WDTRST1"; |
| groups = "WDTRST1"; |
| }; |
| |
| pinctrl_wdtrst2_default: wdtrst2_default { |
| function = "WDTRST2"; |
| groups = "WDTRST2"; |
| }; |
| |
| pinctrl_pcie0rc_default: pcie0rc_default { |
| function = "PCIE0RC"; |
| groups = "PCIE0RC"; |
| }; |
| |
| pinctrl_pcie1rc_default: pcie1rc_default { |
| function = "PCIE1RC"; |
| groups = "PCIE1RC"; |
| }; |
| }; |