include/configs/MPC8569MDS.h - platform/external/u-boot - Gitiles

 /*
  * Copyright 2009-2011 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * mpc8569mds board configuration file
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1			/* SRIO port 1 */

 #define CONFIG_PCIE1		1	/* PCIE controller */
 #define CONFIG_FSL_PCI_INIT	1	/* use common fsl pci init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
 #define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE

 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif
 /* Replace a call to get_clock_freq (after it is implemented)*/
 #define CONFIG_SYS_CLK_FREQ	66666666
 #define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ

 #ifdef CONFIG_ATM
 #define CONFIG_PQ_MDS_PIB
 #define CONFIG_PQ_MDS_PIB_ATM
 #endif

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE				/* toggle L2 cache	*/
 #define CONFIG_BTB				/* toggle branch predition */

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xfff80000
 #endif

 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif

 /*
  * Only possible on E500 Version 2 or newer cores.
  */
 #define CONFIG_ENABLE_36BIT_PHYS	1

 #define CONFIG_BOARD_EARLY_INIT_R	1
 #define CONFIG_HWCONFIG

 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00400000

 /*
  * Config the L2 Cache as L2 SRAM
  */
 #define CONFIG_SYS_INIT_L2_ADDR		0xf8f80000
 #define CONFIG_SYS_INIT_L2_ADDR_PHYS	CONFIG_SYS_INIT_L2_ADDR
 #define CONFIG_SYS_L2_SIZE		(512 << 10)
 #define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)

 #define CONFIG_SYS_CCSRBAR		0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR

 #if defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif

 /* DDR Setup */
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */

 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef

 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 					/* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)

 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS    0x51    /* CTLR 0 DIMM 0 */

 /* These are used when DDR doesn't use SPD.  */
 #define CONFIG_SYS_SDRAM_SIZE           1024		/* DDR is 1024MB */
 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003F
 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014202
 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
 #define CONFIG_SYS_DDR_TIMING_1         0x6F6B4644
 #define CONFIG_SYS_DDR_TIMING_2         0x002888D0
 #define CONFIG_SYS_DDR_SDRAM_CFG	0x47000000
 #define CONFIG_SYS_DDR_SDRAM_CFG_2	0x04401040
 #define CONFIG_SYS_DDR_SDRAM_MODE	0x40401521
 #define CONFIG_SYS_DDR_SDRAM_MODE_2	0x8000C000
 #define CONFIG_SYS_DDR_SDRAM_INTERVAL	0x03E00000
 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	0x01000000
 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 #define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
 #define CONFIG_SYS_DDR_WRLVL_CNTL	0x0655A604
 #define CONFIG_SYS_DDR_CDR_1		0x80040000
 #define CONFIG_SYS_DDR_CDR_2		0x00000000
 #define CONFIG_SYS_DDR_OCD_CTRL         0x00000000
 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 #define CONFIG_SYS_DDR_CONTROL          0xc7000000      /* Type = DDR3 */
 #define CONFIG_SYS_DDR_CONTROL2         0x24400000

 #define CONFIG_SYS_DDR_ERR_INT_EN       0x0000000d
 #define CONFIG_SYS_DDR_ERR_DIS          0x00000000
 #define CONFIG_SYS_DDR_SBE              0x00010000

 #undef CONFIG_CLOCKS_IN_MHZ

 /*
  * Local Bus Definitions
  */

 #define CONFIG_SYS_FLASH_BASE		0xfe000000	/* start of FLASH 32M */
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

 #define CONFIG_SYS_BCSR_BASE		0xf8000000
 #define CONFIG_SYS_BCSR_BASE_PHYS	CONFIG_SYS_BCSR_BASE

 /*Chip select 0 - Flash*/
 #define CONFIG_FLASH_BR_PRELIM		0xfe000801
 #define	CONFIG_FLASH_OR_PRELIM		0xfe000ff7

 /*Chip select 1 - BCSR*/
 #define CONFIG_SYS_BR1_PRELIM		0xf8000801
 #define	CONFIG_SYS_OR1_PRELIM		0xffffe9f7

 /*Chip select 4 - PIB*/
 #define CONFIG_SYS_BR4_PRELIM		0xf8008801
 #define CONFIG_SYS_OR4_PRELIM		0xffffe9f7

 /*Chip select 5 - PIB*/
 #define CONFIG_SYS_BR5_PRELIM		0xf8010801
 #define CONFIG_SYS_OR5_PRELIM		0xffffe9f7

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
 #undef	CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #undef CONFIG_SYS_RAMBOOT

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 /* Chip select 3 - NAND */
 #ifndef CONFIG_NAND_SPL
 #define CONFIG_SYS_NAND_BASE		0xFC000000
 #else
 #define CONFIG_SYS_NAND_BASE		0xFFF00000
 #endif

 /* NAND boot: 4K NAND loader config */
 #define CONFIG_SYS_NAND_SPL_SIZE	0x1000
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	((512 << 10) - 0x2000)
 #define CONFIG_SYS_NAND_U_BOOT_DST	(CONFIG_SYS_INIT_L2_ADDR)
 #define CONFIG_SYS_NAND_U_BOOT_START \
 	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(0)
 #define CONFIG_SYS_NAND_U_BOOT_RELOC	(CONFIG_SYS_INIT_L2_END - 0x2000)
 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)

 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE, }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_NAND_FSL_ELBC		1
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
 #define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE_PHYS \
 				| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
 				| BR_PS_8	     /* Port Size = 8 bit */ \
 				| BR_MS_FCM	     /* MSEL = FCM */ \
 				| BR_V)		     /* valid */
 #define CONFIG_SYS_NAND_OR_PRELIM	(0xFFFC0000	     /* length 256K */ \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
 				| OR_FCM_SCY_1 \
 				| OR_FCM_TRLX \
 				| OR_FCM_EHTR)

 #define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
 #define CONFIG_SYS_BR3_PRELIM	CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 #define CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

 #define CONFIG_SYS_LBC_LCRR	0x00000004	/* LB clock ratio reg */
 #define CONFIG_SYS_LBC_LBCR	0x00040000	/* LB config reg */
 #define CONFIG_SYS_LBC_LSRT	0x20000000	/* LB sdram refresh timer */
 #define CONFIG_SYS_LBC_MRTPR	0x00000000	/* LB refresh timer prescal*/

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000  /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000	    /* Size of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024)	/* Reserved for malloc */

 /* Serial Port */
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 #ifdef CONFIG_NAND_SPL
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif

 #define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)

 /*
  * I2C
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }

 /*
  * I2C2 EEPROM
  */
 #define CONFIG_ID_EEPROM
 #ifdef CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #endif
 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x52
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_SYS_EEPROM_BUS_NUM       1

 #define PLPPAR1_I2C_BIT_MASK		0x0000000F
 #define PLPPAR1_I2C2_VAL		0x00000000
 #define PLPPAR1_ESDHC_VAL		0x0000000A
 #define PLPDIR1_I2C_BIT_MASK		0x0000000F
 #define PLPDIR1_I2C2_VAL		0x0000000F
 #define PLPDIR1_ESDHC_VAL		0x00000006
 #define PLPPAR1_UART0_BIT_MASK		0x00000fc0
 #define PLPPAR1_ESDHC_4BITS_VAL		0x00000a80
 #define PLPDIR1_UART0_BIT_MASK		0x00000fc0
 #define PLPDIR1_ESDHC_4BITS_VAL		0x00000a80

 /*
  * General PCI
  * Memory Addresses are mapped 1-1. I/O is mapped from 0
  */
 #define CONFIG_SYS_PCIE1_NAME		"Slot"
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xe2800000
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe2800000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000	/* 8M */

 #define CONFIG_SYS_SRIO1_MEM_VIRT	0xC0000000
 #define CONFIG_SYS_SRIO1_MEM_BUS	0xC0000000
 #define CONFIG_SYS_SRIO1_MEM_PHYS	CONFIG_SYS_SRIO1_MEM_BUS
 #define CONFIG_SYS_SRIO1_MEM_SIZE	0x20000000	/* 512M */

 #ifdef CONFIG_QE
 /*
  * QE UEC ethernet configuration
  */
 #define CONFIG_SYS_UCC_RGMII_MODE	/* Set UCC work at RGMII by default */
 #undef CONFIG_SYS_UCC_RMII_MODE		/* Set UCC work at RMII mode */

 #define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
 #define CONFIG_UEC_ETH
 #define CONFIG_ETHPRIME         "UEC0"
 #define CONFIG_PHY_MODE_NEED_CHANGE

 #define CONFIG_UEC_ETH1         /* GETH1 */
 #define CONFIG_HAS_ETH0

 #ifdef CONFIG_UEC_ETH1
 #define CONFIG_SYS_UEC1_UCC_NUM        0       /* UCC1 */
 #define CONFIG_SYS_UEC1_RX_CLK         QE_CLK_NONE
 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK12
 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       7
 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16	/* CLK16 for RMII */
 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       8	/* 0x8 for RMII */
 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH1 */

 #define CONFIG_UEC_ETH2         /* GETH2 */
 #define CONFIG_HAS_ETH1

 #ifdef CONFIG_UEC_ETH2
 #define CONFIG_SYS_UEC2_UCC_NUM        1       /* UCC2 */
 #define CONFIG_SYS_UEC2_RX_CLK         QE_CLK_NONE
 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK17
 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       1
 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16	/* CLK 16 for RMII */
 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       0x9	/* 0x9 for RMII */
 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH2 */

 #define CONFIG_UEC_ETH3         /* GETH3 */
 #define CONFIG_HAS_ETH2

 #ifdef CONFIG_UEC_ETH3
 #define CONFIG_SYS_UEC3_UCC_NUM        2       /* UCC3 */
 #define CONFIG_SYS_UEC3_RX_CLK         QE_CLK_NONE
 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 #define CONFIG_SYS_UEC3_TX_CLK         QE_CLK12
 #define CONFIG_SYS_UEC3_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC3_PHY_ADDR       2
 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC3_TX_CLK		QE_CLK16 /* CLK_16 for RMII */
 #define CONFIG_SYS_UEC3_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC3_PHY_ADDR	0xA     /* 0xA for RMII */
 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH3 */

 #define CONFIG_UEC_ETH4         /* GETH4 */
 #define CONFIG_HAS_ETH3

 #ifdef CONFIG_UEC_ETH4
 #define CONFIG_SYS_UEC4_UCC_NUM        3       /* UCC4 */
 #define CONFIG_SYS_UEC4_RX_CLK         QE_CLK_NONE
 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 #define CONFIG_SYS_UEC4_TX_CLK         QE_CLK17
 #define CONFIG_SYS_UEC4_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC4_PHY_ADDR       3
 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 #define CONFIG_SYS_UEC4_TX_CLK		QE_CLK16 /* CLK16 for RMII */
 #define CONFIG_SYS_UEC4_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC4_PHY_ADDR	0xB     /* 0xB for RMII */
 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 #endif /* CONFIG_UEC_ETH4 */

 #undef CONFIG_UEC_ETH6         /* GETH6 */
 #define CONFIG_HAS_ETH5

 #ifdef CONFIG_UEC_ETH6
 #define CONFIG_SYS_UEC6_UCC_NUM        5       /* UCC6 */
 #define CONFIG_SYS_UEC6_RX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC6_TX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC6_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC6_PHY_ADDR       4
 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
 #endif /* CONFIG_UEC_ETH6 */

 #undef CONFIG_UEC_ETH8         /* GETH8 */
 #define CONFIG_HAS_ETH7

 #ifdef CONFIG_UEC_ETH8
 #define CONFIG_SYS_UEC8_UCC_NUM        7       /* UCC8 */
 #define CONFIG_SYS_UEC8_RX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC8_TX_CLK         QE_CLK_NONE
 #define CONFIG_SYS_UEC8_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC8_PHY_ADDR       6
 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
 #endif /* CONFIG_UEC_ETH8 */

 #endif /* CONFIG_QE */

 #if defined(CONFIG_PCI)
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP

 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */

 #endif	/* CONFIG_PCI */

 /*
  * Environment
  */
 #if defined(CONFIG_SYS_RAMBOOT)
 #else
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
 #define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 #define CONFIG_SYS_QE_FW_ADDR	0xfff00000

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_ESDHC_PIN_MUX
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING			/* Command-line editing */
 #define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	2048		/* Console I/O Buffer Size */
 #else
 #define CONFIG_SYS_CBSIZE	512		/* Console I/O Buffer Size */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 						/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	32		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
 						/* Boot Argument Buffer Size */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20) /* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_HOSTNAME mpc8569mds
 #define CONFIG_ROOTPATH  "/nfsroot"
 #define CONFIG_BOOTFILE  "your.uImage"

 #define CONFIG_SERVERIP  192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1
 #define CONFIG_NETMASK   255.255.255.0

 #define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/

 #undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"consoledev=ttyS0\0"						\
 	"ramdiskaddr=600000\0"						\
 	"ramdiskfile=your.ramdisk.u-boot\0"				\
 	"fdtaddr=400000\0"						\
 	"fdtfile=your.fdt.dtb\0"					\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 	"nfsroot=$serverip:$rootpath "					\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 	"console=$consoledev,$baudrate $othbootargs\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw "			\
 	"console=$consoledev,$baudrate $othbootargs\0"			\

 #define CONFIG_NFSBOOTCOMMAND						\
 	"run nfsargs;"							\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"run ramargs;"							\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"bootm $loadaddr $ramdiskaddr"

 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2009-2011 Freescale Semiconductor, Inc.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* mpc8569mds board configuration file
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_SYS_SRIO
	#define CONFIG_SRIO1 /* SRIO port 1 */

	#define CONFIG_PCIE1 1 /* PCIE controller */
	#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
	#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
	#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
	#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
	#define CONFIG_QE /* Enable QE */
	#define CONFIG_ENV_OVERWRITE

	#ifndef __ASSEMBLY__
	extern unsigned long get_clock_freq(void);
	#endif
	/* Replace a call to get_clock_freq (after it is implemented)*/
	#define CONFIG_SYS_CLK_FREQ 66666666
	#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ

	#ifdef CONFIG_ATM
	#define CONFIG_PQ_MDS_PIB
	#define CONFIG_PQ_MDS_PIB_ATM
	#endif

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_L2_CACHE /* toggle L2 cache */
	#define CONFIG_BTB /* toggle branch predition */

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xfff80000
	#endif

	#ifndef CONFIG_SYS_MONITOR_BASE
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	/*
	* Only possible on E500 Version 2 or newer cores.
	*/
	#define CONFIG_ENABLE_36BIT_PHYS 1

	#define CONFIG_BOARD_EARLY_INIT_R 1
	#define CONFIG_HWCONFIG

	#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00400000

	/*
	* Config the L2 Cache as L2 SRAM
	*/
	#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000
	#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR
	#define CONFIG_SYS_L2_SIZE (512 << 10)
	#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)

	#define CONFIG_SYS_CCSRBAR 0xe0000000
	#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

	#if defined(CONFIG_NAND_SPL)
	#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
	#endif

	/* DDR Setup */
	#undef CONFIG_FSL_DDR_INTERACTIVE
	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
	#define CONFIG_DDR_SPD
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */

	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	/* DDR is system memory*/
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)

	/* I2C addresses of SPD EEPROMs */
	#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */

	/* These are used when DDR doesn't use SPD. */
	#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */
	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
	#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202
	#define CONFIG_SYS_DDR_TIMING_3 0x00020000
	#define CONFIG_SYS_DDR_TIMING_0 0x00330004
	#define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644
	#define CONFIG_SYS_DDR_TIMING_2 0x002888D0
	#define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000
	#define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040
	#define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521
	#define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000
	#define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000
	#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000
	#define CONFIG_SYS_DDR_TIMING_4 0x00220001
	#define CONFIG_SYS_DDR_TIMING_5 0x03402400
	#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
	#define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604
	#define CONFIG_SYS_DDR_CDR_1 0x80040000
	#define CONFIG_SYS_DDR_CDR_2 0x00000000
	#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
	#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
	#define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */
	#define CONFIG_SYS_DDR_CONTROL2 0x24400000

	#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
	#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
	#define CONFIG_SYS_DDR_SBE 0x00010000

	#undef CONFIG_CLOCKS_IN_MHZ

	/*
	* Local Bus Definitions
	*/

	#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE

	#define CONFIG_SYS_BCSR_BASE 0xf8000000
	#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE

	/Chip select 0 - Flash/
	#define CONFIG_FLASH_BR_PRELIM 0xfe000801
	#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7

	/Chip select 1 - BCSR/
	#define CONFIG_SYS_BR1_PRELIM 0xf8000801
	#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7

	/Chip select 4 - PIB/
	#define CONFIG_SYS_BR4_PRELIM 0xf8008801
	#define CONFIG_SYS_OR4_PRELIM 0xffffe9f7

	/Chip select 5 - PIB/
	#define CONFIG_SYS_BR5_PRELIM 0xf8010801
	#define CONFIG_SYS_OR5_PRELIM 0xffffe9f7

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#undef CONFIG_SYS_RAMBOOT

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	/* Chip select 3 - NAND */
	#ifndef CONFIG_NAND_SPL
	#define CONFIG_SYS_NAND_BASE 0xFC000000
	#else
	#define CONFIG_SYS_NAND_BASE 0xFFF00000
	#endif

	/* NAND boot: 4K NAND loader config */
	#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
	#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000)
	#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR)
	#define CONFIG_SYS_NAND_U_BOOT_START \
	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
	#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
	#define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000)
	#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)

	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_NAND_FSL_ELBC 1
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
	#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8 bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)

	#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
	#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

	#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */
	#define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */
	#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
	#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	#ifdef CONFIG_NAND_SPL
	#define CONFIG_NS16550_MIN_FUNCTIONS
	#endif

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)

	/*
	* I2C
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }

	/*
	* I2C2 EEPROM
	*/
	#define CONFIG_ID_EEPROM
	#ifdef CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#endif
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_BUS_NUM 1

	#define PLPPAR1_I2C_BIT_MASK 0x0000000F
	#define PLPPAR1_I2C2_VAL 0x00000000
	#define PLPPAR1_ESDHC_VAL 0x0000000A
	#define PLPDIR1_I2C_BIT_MASK 0x0000000F
	#define PLPDIR1_I2C2_VAL 0x0000000F
	#define PLPDIR1_ESDHC_VAL 0x00000006
	#define PLPPAR1_UART0_BIT_MASK 0x00000fc0
	#define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80
	#define PLPDIR1_UART0_BIT_MASK 0x00000fc0
	#define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80

	/*
	* General PCI
	* Memory Addresses are mapped 1-1. I/O is mapped from 0
	*/
	#define CONFIG_SYS_PCIE1_NAME "Slot"
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */

	#define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000
	#define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000
	#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS
	#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */

	#ifdef CONFIG_QE
	/*
	* QE UEC ethernet configuration
	*/
	#define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */
	#undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */

	#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
	#define CONFIG_UEC_ETH
	#define CONFIG_ETHPRIME "UEC0"
	#define CONFIG_PHY_MODE_NEED_CHANGE

	#define CONFIG_UEC_ETH1 /* GETH1 */
	#define CONFIG_HAS_ETH0

	#ifdef CONFIG_UEC_ETH1
	#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
	#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
	#if defined(CONFIG_SYS_UCC_RGMII_MODE)
	#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12
	#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC1_PHY_ADDR 7
	#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
	#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
	#elif defined(CONFIG_SYS_UCC_RMII_MODE)
	#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */
	#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */
	#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
	#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
	#endif /* CONFIG_SYS_UCC_RGMII_MODE */
	#endif /* CONFIG_UEC_ETH1 */

	#define CONFIG_UEC_ETH2 /* GETH2 */
	#define CONFIG_HAS_ETH1

	#ifdef CONFIG_UEC_ETH2
	#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
	#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
	#if defined(CONFIG_SYS_UCC_RGMII_MODE)
	#define CONFIG_SYS_UEC2_TX_CLK QE_CLK17
	#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC2_PHY_ADDR 1
	#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
	#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
	#elif defined(CONFIG_SYS_UCC_RMII_MODE)
	#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */
	#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */
	#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
	#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
	#endif /* CONFIG_SYS_UCC_RGMII_MODE */
	#endif /* CONFIG_UEC_ETH2 */

	#define CONFIG_UEC_ETH3 /* GETH3 */
	#define CONFIG_HAS_ETH2

	#ifdef CONFIG_UEC_ETH3
	#define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */
	#define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE
	#if defined(CONFIG_SYS_UCC_RGMII_MODE)
	#define CONFIG_SYS_UEC3_TX_CLK QE_CLK12
	#define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC3_PHY_ADDR 2
	#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
	#define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
	#elif defined(CONFIG_SYS_UCC_RMII_MODE)
	#define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */
	#define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */
	#define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
	#define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
	#endif /* CONFIG_SYS_UCC_RGMII_MODE */
	#endif /* CONFIG_UEC_ETH3 */

	#define CONFIG_UEC_ETH4 /* GETH4 */
	#define CONFIG_HAS_ETH3

	#ifdef CONFIG_UEC_ETH4
	#define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */
	#define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE
	#if defined(CONFIG_SYS_UCC_RGMII_MODE)
	#define CONFIG_SYS_UEC4_TX_CLK QE_CLK17
	#define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC4_PHY_ADDR 3
	#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
	#define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
	#elif defined(CONFIG_SYS_UCC_RMII_MODE)
	#define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */
	#define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */
	#define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
	#define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
	#endif /* CONFIG_SYS_UCC_RGMII_MODE */
	#endif /* CONFIG_UEC_ETH4 */

	#undef CONFIG_UEC_ETH6 /* GETH6 */
	#define CONFIG_HAS_ETH5

	#ifdef CONFIG_UEC_ETH6
	#define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */
	#define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE
	#define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE
	#define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC6_PHY_ADDR 4
	#define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
	#define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
	#endif /* CONFIG_UEC_ETH6 */

	#undef CONFIG_UEC_ETH8 /* GETH8 */
	#define CONFIG_HAS_ETH7

	#ifdef CONFIG_UEC_ETH8
	#define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */
	#define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE
	#define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE
	#define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH
	#define CONFIG_SYS_UEC8_PHY_ADDR 6
	#define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
	#define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
	#endif /* CONFIG_UEC_ETH8 */

	#endif /* CONFIG_QE */

	#if defined(CONFIG_PCI)
	#undef CONFIG_EEPRO100
	#undef CONFIG_TULIP

	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */

	#endif /* CONFIG_PCI */

	/*
	* Environment
	*/
	#if defined(CONFIG_SYS_RAMBOOT)
	#else
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/* QE microcode/firmware address */
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	#define CONFIG_SYS_QE_FW_ADDR 0xfff00000

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	#ifdef CONFIG_MMC
	#define CONFIG_FSL_ESDHC
	#define CONFIG_FSL_ESDHC_PIN_MUX
	#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	/* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	/* Boot Argument Buffer Size */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_HOSTNAME mpc8569mds
	#define CONFIG_ROOTPATH "/nfsroot"
	#define CONFIG_BOOTFILE "your.uImage"

	#define CONFIG_SERVERIP 192.168.1.1
	#define CONFIG_GATEWAYIP 192.168.1.1
	#define CONFIG_NETMASK 255.255.255.0

	#define CONFIG_LOADADDR 200000 /default location for tftp and bootm/

	#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=600000\0" \
	"ramdiskfile=your.ramdisk.u-boot\0" \
	"fdtaddr=400000\0" \
	"fdtfile=your.fdt.dtb\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs\0" \
	"ramargs=setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs\0" \

	#define CONFIG_NFSBOOTCOMMAND \
	"run nfsargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"run ramargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"bootm $loadaddr $ramdiskaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

	#endif /* __CONFIG_H */