blob: 19c8a5aa235419d1cdef886bbcf9a225b60f132a [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2019 NXP
*/
#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <hang.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/io.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mm_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/arch/ddr.h>
#include <dm/uclass.h>
#include <dm/device.h>
#include <dm/uclass-internal.h>
#include <dm/device-internal.h>
#include <power/pmic.h>
#include <power/bd71837.h>
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
switch (boot_dev_spl) {
case SD2_BOOT:
case MMC2_BOOT:
return BOOT_DEVICE_MMC1;
case SD3_BOOT:
case MMC3_BOOT:
return BOOT_DEVICE_MMC2;
default:
return BOOT_DEVICE_NONE;
}
}
static void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
void spl_board_init(void)
{
puts("Normal Boot\n");
}
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
static iomux_v3_cfg_t const uart_pads[] = {
IMX8MM_PAD_UART2_RXD_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
IMX8MM_PAD_UART2_TXD_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
int board_early_init_f(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
return 0;
}
static int power_init_board(void)
{
struct udevice *dev;
int ret;
ret = pmic_get("pmic@4b", &dev);
if (ret == -ENODEV) {
puts("No pmic\n");
return 0;
}
if (ret != 0)
return ret;
/* decrease RESET key long push time from the default 10s to 10ms */
pmic_reg_write(dev, BD718XX_PWRONCONFIG1, 0x0);
/* unlock the PMIC regs */
pmic_reg_write(dev, BD718XX_REGLOCK, 0x1);
/* increase VDD_SOC to typical value 0.85v before first DRAM access */
pmic_reg_write(dev, BD718XX_BUCK1_VOLT_RUN, 0x0f);
/* increase VDD_DRAM to 0.975v for 3Ghz DDR */
pmic_reg_write(dev, BD718XX_1ST_NODVS_BUCK_VOLT, 0x83);
#ifndef CONFIG_IMX8M_LPDDR4
/* increase NVCC_DRAM_1V2 to 1.2v for DDR4 */
pmic_reg_write(dev, BD718XX_4TH_NODVS_BUCK_VOLT, 0x28);
#endif
/* lock the PMIC regs */
pmic_reg_write(dev, BD718XX_REGLOCK, 0x11);
return 0;
}
void board_init_f(ulong dummy)
{
struct udevice *dev;
int ret;
arch_cpu_init();
init_uart_clk(1);
board_early_init_f();
timer_init();
preloader_console_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
ret = uclass_get_device_by_name(UCLASS_CLK,
"clock-controller@30380000",
&dev);
if (ret < 0) {
printf("Failed to find clock node. Check device tree\n");
hang();
}
enable_tzc380();
power_init_board();
/* DDR initialization */
spl_dram_init();
board_init_r(NULL, 0);
}