include/configs/mcx.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2011 Ilya Yanok, Emcraft Systems
  *
  * Based on omap3_evm_config.h
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */

 #define CONFIG_MACH_TYPE	MACH_TYPE_MCX

 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap.h>

 /*
  * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
  * and older u-boot.bin with the new U-Boot SPL.
  */

 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)

 #define CONFIG_MISC_INIT_R

 #define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 #define CONFIG_REVISION_TAG

 /*
  * Size of malloc() pool
  */
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB sector */
 #define CONFIG_SYS_MALLOC_LEN		(1024 << 10)
 /*
  * DDR related
  */
 #define CONFIG_SYS_CS0_SIZE		(256 * 1024 * 1024)

 /*
  * Hardware drivers
  */

 /*
  * NS16550 Configuration
  */
 #define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

 /*
  * select serial console configuration
  */
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
 #define CONFIG_SERIAL3			3	/* UART3 */

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}

 /* EHCI */
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	57

 /* commands to include */

 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_MTD_DEVICE

 #define CONFIG_SYS_I2C

 /* RTC */
 #define CONFIG_RTC_DS1337
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68

 /*
  * Board NAND Info.
  */
 #define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
 							/* to access nand */
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
 							/* to access */
 							/* nand at CS0 */

 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
 							/* NAND devices */
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
 #define CONFIG_JFFS2_DEV		"nand0"
 /* start of jffs2 partition */
 #define CONFIG_JFFS2_PART_OFFSET	0x680000
 #define CONFIG_JFFS2_PART_SIZE		0xf980000	/* sz of jffs2 part */

 /* Environment information */

 #define CONFIG_BOOTFILE		"uImage"

 /* Setup MTD for NAND on the SOM */

 #define CONFIG_HOSTNAME mcx
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"adddbg=setenv bootargs ${bootargs} trace_buf_size=64M\0"	\
 	"adddebug=setenv bootargs ${bootargs} earlyprintk=serial\0"	\
 	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0"	\
 	"addfb=setenv bootargs ${bootargs} vram=6M "			\
 		"omapfb.vram=1:2M,2:2M,3:2M omapdss.def_disp=lcd\0"	\
 	"addip_sta=setenv bootargs ${bootargs} "			\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
 		"${netmask}:${hostname}:eth0:off\0"			\
 	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
 	"addip=if test -n ${ipdyn};then run addip_dyn;"			\
 		"else run addip_sta;fi\0"				\
 	"addmisc=setenv bootargs ${bootargs} ${misc}\0"			\
 	"addtty=setenv bootargs ${bootargs} "				\
 		"console=${consoledev},${baudrate}\0"			\
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
 	"baudrate=115200\0"						\
 	"consoledev=ttyO2\0"						\
 	"hostname=" __stringify(CONFIG_HOSTNAME) "\0"			\
 	"loadaddr=0x82000000\0"						\
 	"load=tftp ${loadaddr} ${u-boot}\0"				\
 	"load_k=tftp ${loadaddr} ${bootfile}\0"				\
 	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0"			\
 	"loadmlo=tftp ${loadaddr} ${mlo}\0"				\
 	"mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0"			\
 	"mmcargs=root=/dev/mmcblk0p2 rw "				\
 		"rootfstype=ext3 rootwait\0"				\
 	"mmcboot=echo Booting from mmc ...; "				\
 		"run mmcargs; "						\
 		"run addip addtty addmtd addfb addeth addmisc;"		\
 		"run loaduimage; "					\
 		"bootm ${loadaddr}\0"					\
 	"net_nfs=run load_k; "						\
 		"run nfsargs; "						\
 		"run addip addtty addmtd addfb addeth addmisc;"		\
 		"bootm ${loadaddr}\0"					\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0"		\
 	"uboot_addr=0x80000\0"						\
 	"update=nandecc sw;nand erase ${uboot_addr} 100000;"		\
 		"nand write ${loadaddr} ${uboot_addr} 80000\0"		\
 	"updatemlo=nandecc hw;nand erase 0 20000;"			\
 		"nand write ${loadaddr} 0 20000\0"			\
 	"upd=if run load;then echo Updating u-boot;if run update;"	\
 		"then echo U-Boot updated;"				\
 			"else echo Error updating u-boot !;"		\
 			"echo Board without bootloader !!;"		\
 		"fi;"							\
 		"else echo U-Boot not downloaded..exiting;fi\0"		\
 	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0"		\
 	"bootscript=echo Running bootscript from mmc ...; "		\
 		"source ${loadaddr}\0"					\
 	"nandargs=setenv bootargs ubi.mtd=7 "				\
 		"root=ubi0:rootfs rootfstype=ubifs\0"			\
 	"nandboot=echo Booting from nand ...; "				\
 		"run nandargs; "					\
 		"ubi part nand0,4;"					\
 		"ubi readvol ${loadaddr} kernel;"			\
 		"run addtty addmtd addfb addeth addmisc;"		\
 		"bootm ${loadaddr}\0"					\
 	"preboot=ubi part nand0,7;"					\
 		"ubi readvol ${loadaddr} splash;"			\
 		"bmp display ${loadaddr};"				\
 		"gpio set 55\0"						\
 	"swupdate_args=setenv bootargs root=/dev/ram "			\
 		"quiet loglevel=1 "					\
 		"consoleblank=0 ${swupdate_misc}\0"			\
 	"swupdate=echo Running Sw-Update...;"				\
 		"if printenv mtdparts;then echo Starting SwUpdate...; "	\
 		"else mtdparts default;fi; "				\
 		"ubi part nand0,5;"					\
 		"ubi readvol 0x82000000 kernel_recovery;"		\
 		"ubi part nand0,6;"					\
 		"ubi readvol 0x84000000 fs_recovery;"			\
 		"run swupdate_args; "					\
 		"setenv bootargs ${bootargs} "				\
 			"${mtdparts} "					\
 			"vram=6M omapfb.vram=1:2M,2:2M,3:2M "		\
 			"omapdss.def_disp=lcd;"				\
 		"bootm 0x82000000 0x84000000\0"				\
 	"bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;"	\
 		"then source 82000000;else run nandboot;fi\0"

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_CBSIZE		1024/* Console I/O Buffer Size */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)
 /* memtest works on */
 #define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0)
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + \
 					0x01F00000) /* 31MB */

 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0) /* default load */
 								/* address */
 #define CONFIG_PREBOOT

 /*
  * AM3517 has 12 GP timers, they can be driven by the system clock
  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  * This rate is divided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		OMAP34XX_GPT2
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */

 /*
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1

 /*
  * FLASH and environment organization
  */

 /* **** PISMO SUPPORT *** */

 /* Redundant Environment */
 #define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
 #define CONFIG_ENV_OFFSET		0x180000
 #define CONFIG_ENV_ADDR			0x180000
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
 						2 * CONFIG_SYS_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE

 /* Flash banks JFFS2 should use */
 #define CONFIG_SYS_MAX_MTD_BANKS	(CONFIG_SYS_MAX_FLASH_BANKS + \
 					CONFIG_SYS_MAX_NAND_DEVICE)
 #define CONFIG_SYS_JFFS2_MEM_NAND
 /* use flash_info[2] */
 #define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
 #define CONFIG_SYS_JFFS2_NUM_BANKS	1

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
 #define CONFIG_SYS_INIT_RAM_SIZE	0x800
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)

 /* Defines for SPL */

 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_ECC

 #define CONFIG_SPL_TEXT_BASE		0x40200000 /*CONFIG_SYS_SRAM_START*/
 #define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */
 #define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK

 /* move malloc and bss high to prevent clashing with the main image */
 #define CONFIG_SYS_SPL_MALLOC_START	0x8f000000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000
 #define CONFIG_SPL_BSS_START_ADDR	0x8f080000 /* end of RAM */
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"

 /* NAND boot config */
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
 #define CONFIG_SYS_NAND_OOBSIZE		64
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
 #define CONFIG_SYS_NAND_ECCPOS		{40, 41, 42, 43, 44, 45, 46, 47,\
 					 48, 49, 50, 51, 52, 53, 54, 55,\
 					 56, 57, 58, 59, 60, 61, 62, 63}
 #define CONFIG_SYS_NAND_ECCSIZE		256
 #define CONFIG_SYS_NAND_ECCBYTES	3
 #define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_SW
 #define CONFIG_SPL_NAND_SOFTECC

 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE

 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000

 /*
  * ethernet support
  *
  */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_DRIVER_TI_EMAC
 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 #define CONFIG_MII
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 #define CONFIG_NET_RETRY_COUNT 10
 #endif

 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_VIDEO_BMP_RLE8
 #define CONFIG_VIDEO_OMAP3

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2011 Ilya Yanok, Emcraft Systems
	*
	* Based on omap3_evm_config.h
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/

	#define CONFIG_MACH_TYPE MACH_TYPE_MCX

	#include <asm/arch/cpu.h> /* get chip and board defs */
	#include <asm/arch/omap.h>

	/*
	* Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
	* and older u-boot.bin with the new U-Boot SPL.
	*/

	/* Clock Defines */
	#define V_OSCK 26000000 /* Clock output from T2 */
	#define V_SCLK (V_OSCK >> 1)

	#define CONFIG_MISC_INIT_R

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG
	#define CONFIG_REVISION_TAG

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
	#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
	/*
	* DDR related
	*/
	#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)

	/*
	* Hardware drivers
	*/

	/*
	* NS16550 Configuration
	*/
	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */

	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK

	/*
	* select serial console configuration
	*/
	#define CONFIG_CONS_INDEX 3
	#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
	#define CONFIG_SERIAL3 3 /* UART3 */

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
	115200}

	/* EHCI */
	#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57

	/* commands to include */

	#define CONFIG_MTD_PARTITIONS
	#define CONFIG_MTD_DEVICE

	#define CONFIG_SYS_I2C

	/* RTC */
	#define CONFIG_RTC_DS1337
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68

	/*
	* Board NAND Info.
	*/
	#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
	/* to access nand */
	#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
	/* to access */
	/* nand at CS0 */

	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
	/* NAND devices */
	#define CONFIG_JFFS2_NAND
	/* nand device jffs2 lives on */
	#define CONFIG_JFFS2_DEV "nand0"
	/* start of jffs2 partition */
	#define CONFIG_JFFS2_PART_OFFSET 0x680000
	#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */

	/* Environment information */

	#define CONFIG_BOOTFILE "uImage"

	/* Setup MTD for NAND on the SOM */

	#define CONFIG_HOSTNAME mcx
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"adddbg=setenv bootargs ${bootargs} trace_buf_size=64M\0" \
	"adddebug=setenv bootargs ${bootargs} earlyprintk=serial\0" \
	"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \
	"addfb=setenv bootargs ${bootargs} vram=6M " \
	"omapfb.vram=1:2M,2:2M,3:2M omapdss.def_disp=lcd\0" \
	"addip_sta=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
	"${netmask}:${hostname}:eth0:off\0" \
	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
	"addip=if test -n ${ipdyn};then run addip_dyn;" \
	"else run addip_sta;fi\0" \
	"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
	"addtty=setenv bootargs ${bootargs} " \
	"console=${consoledev},${baudrate}\0" \
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	"baudrate=115200\0" \
	"consoledev=ttyO2\0" \
	"hostname=" __stringify(CONFIG_HOSTNAME) "\0" \
	"loadaddr=0x82000000\0" \
	"load=tftp ${loadaddr} ${u-boot}\0" \
	"load_k=tftp ${loadaddr} ${bootfile}\0" \
	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
	"loadmlo=tftp ${loadaddr} ${mlo}\0" \
	"mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \
	"mmcargs=root=/dev/mmcblk0p2 rw " \
	"rootfstype=ext3 rootwait\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"run addip addtty addmtd addfb addeth addmisc;" \
	"run loaduimage; " \
	"bootm ${loadaddr}\0" \
	"net_nfs=run load_k; " \
	"run nfsargs; " \
	"run addip addtty addmtd addfb addeth addmisc;" \
	"bootm ${loadaddr}\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \
	"uboot_addr=0x80000\0" \
	"update=nandecc sw;nand erase ${uboot_addr} 100000;" \
	"nand write ${loadaddr} ${uboot_addr} 80000\0" \
	"updatemlo=nandecc hw;nand erase 0 20000;" \
	"nand write ${loadaddr} 0 20000\0" \
	"upd=if run load;then echo Updating u-boot;if run update;" \
	"then echo U-Boot updated;" \
	"else echo Error updating u-boot !;" \
	"echo Board without bootloader !!;" \
	"fi;" \
	"else echo U-Boot not downloaded..exiting;fi\0" \
	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source ${loadaddr}\0" \
	"nandargs=setenv bootargs ubi.mtd=7 " \
	"root=ubi0:rootfs rootfstype=ubifs\0" \
	"nandboot=echo Booting from nand ...; " \
	"run nandargs; " \
	"ubi part nand0,4;" \
	"ubi readvol ${loadaddr} kernel;" \
	"run addtty addmtd addfb addeth addmisc;" \
	"bootm ${loadaddr}\0" \
	"preboot=ubi part nand0,7;" \
	"ubi readvol ${loadaddr} splash;" \
	"bmp display ${loadaddr};" \
	"gpio set 55\0" \
	"swupdate_args=setenv bootargs root=/dev/ram " \
	"quiet loglevel=1 " \
	"consoleblank=0 ${swupdate_misc}\0" \
	"swupdate=echo Running Sw-Update...;" \
	"if printenv mtdparts;then echo Starting SwUpdate...; " \
	"else mtdparts default;fi; " \
	"ubi part nand0,5;" \
	"ubi readvol 0x82000000 kernel_recovery;" \
	"ubi part nand0,6;" \
	"ubi readvol 0x84000000 fs_recovery;" \
	"run swupdate_args; " \
	"setenv bootargs ${bootargs} " \
	"${mtdparts} " \
	"vram=6M omapfb.vram=1:2M,2:2M,3:2M " \
	"omapdss.def_disp=lcd;" \
	"bootm 0x82000000 0x84000000\0" \
	"bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \
	"then source 82000000;else run nandboot;fi\0"

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
	/* memtest works on */
	#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
	#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
	0x01F00000) /* 31MB */

	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
	/* address */
	#define CONFIG_PREBOOT

	/*
	* AM3517 has 12 GP timers, they can be driven by the system clock
	* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
	* This rate is divided by a local divisor.
	*/
	#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */

	/*
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1

	/*
	* FLASH and environment organization
	*/

	/* ** PISMO SUPPORT * */

	/* Redundant Environment */
	#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
	#define CONFIG_ENV_OFFSET 0x180000
	#define CONFIG_ENV_ADDR 0x180000
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	2 * CONFIG_SYS_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE

	/* Flash banks JFFS2 should use */
	#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
	CONFIG_SYS_MAX_NAND_DEVICE)
	#define CONFIG_SYS_JFFS2_MEM_NAND
	/* use flash_info[2] */
	#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
	#define CONFIG_SYS_JFFS2_NUM_BANKS 1

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
	#define CONFIG_SYS_INIT_RAM_SIZE 0x800
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	/* Defines for SPL */

	#define CONFIG_SPL_NAND_BASE
	#define CONFIG_SPL_NAND_DRIVERS
	#define CONFIG_SPL_NAND_ECC

	#define CONFIG_SPL_TEXT_BASE 0x40200000 /CONFIG_SYS_SRAM_START/
	#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
	#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

	/* move malloc and bss high to prevent clashing with the main image */
	#define CONFIG_SYS_SPL_MALLOC_START 0x8f000000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
	#define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"

	/* NAND boot config */
	#define CONFIG_SYS_NAND_PAGE_COUNT 64
	#define CONFIG_SYS_NAND_PAGE_SIZE 2048
	#define CONFIG_SYS_NAND_OOBSIZE 64
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
	#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\
	48, 49, 50, 51, 52, 53, 54, 55,\
	56, 57, 58, 59, 60, 61, 62, 63}
	#define CONFIG_SYS_NAND_ECCSIZE 256
	#define CONFIG_SYS_NAND_ECCBYTES 3
	#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
	#define CONFIG_SPL_NAND_SOFTECC

	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE

	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000

	/*
	* ethernet support
	*
	*/
	#if defined(CONFIG_CMD_NET)
	#define CONFIG_DRIVER_TI_EMAC
	#define CONFIG_DRIVER_TI_EMAC_USE_RMII
	#define CONFIG_MII
	#define CONFIG_BOOTP_DNS2
	#define CONFIG_BOOTP_SEND_HOSTNAME
	#define CONFIG_NET_RETRY_COUNT 10
	#endif

	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_VIDEO_BMP_RLE8
	#define CONFIG_VIDEO_OMAP3

	#endif /* __CONFIG_H */