| CONFIG_ARM=y |
| CONFIG_ARCH_CPU_INIT=y |
| CONFIG_ARCH_AT91=y |
| CONFIG_SYS_TEXT_BASE=0x26f00000 |
| CONFIG_TARGET_SAMA5D3XEK=y |
| CONFIG_SYS_MALLOC_F_LEN=0x2000 |
| CONFIG_DM_GPIO=y |
| CONFIG_NR_DRAM_BANKS=1 |
| CONFIG_DEBUG_UART_BOARD_INIT=y |
| CONFIG_DEBUG_UART_BASE=0xffffee00 |
| CONFIG_DEBUG_UART_CLOCK=132000000 |
| CONFIG_ENV_OFFSET_REDUND=0x100000 |
| CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp" |
| CONFIG_DEBUG_UART=y |
| CONFIG_ENV_VARS_UBOOT_CONFIG=y |
| CONFIG_FIT=y |
| CONFIG_NAND_BOOT=y |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTARGS=y |
| CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256K(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs" |
| # CONFIG_CONSOLE_MUX is not set |
| CONFIG_SYS_CONSOLE_IS_IN_ENV=y |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_HUSH_PARSER=y |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_IMI is not set |
| # CONFIG_CMD_LOADS is not set |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_NAND_TRIMFFS=y |
| CONFIG_CMD_DHCP=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_FAT=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y |
| CONFIG_DM=y |
| CONFIG_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_AT91_H32MX=y |
| CONFIG_AT91_GPIO=y |
| CONFIG_DM_MMC=y |
| CONFIG_GENERIC_ATMEL_MCI=y |
| CONFIG_MTD=y |
| # CONFIG_SYS_NAND_USE_FLASH_BBT is not set |
| CONFIG_NAND_ATMEL=y |
| CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SF_DEFAULT_SPEED=30000000 |
| CONFIG_SPI_FLASH_ATMEL=y |
| CONFIG_DM_ETH=y |
| CONFIG_MACB=y |
| CONFIG_PINCTRL=y |
| CONFIG_PINCTRL_AT91=y |
| CONFIG_DM_SERIAL=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_SPI=y |
| CONFIG_DM_SPI=y |
| CONFIG_TIMER=y |
| CONFIG_ATMEL_PIT_TIMER=y |
| CONFIG_DM_VIDEO=y |
| # CONFIG_VIDEO_BPP8 is not set |
| # CONFIG_VIDEO_BPP32 is not set |
| CONFIG_ATMEL_HLCD=y |