| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2014 Gateworks Corporation |
| * Author: Tim Harvey <tharvey@gateworks.com> |
| */ |
| #ifndef __IMX6_SPL_CONFIG_H |
| #define __IMX6_SPL_CONFIG_H |
| |
| #ifdef CONFIG_SPL |
| |
| #ifdef CONFIG_MX6_OCRAM_256KB |
| /* |
| * see Figure 8.4.1 in IMX6DQ Reference manuals: |
| * - IMX6DQ OCRAM (IRAM) is from 0x00907000 to 0x0093FFFF |
| * - BOOT ROM stack is at 0x0093FFB8 |
| * - if icache/dcache is enabled (eFuse/strapping controlled) then the |
| * IMX BOOT ROM will setup MMU table at 0x00938000, therefore we need to |
| * fit between 0x00907000 and 0x00938000. |
| * - Additionally the BOOT ROM loads what they consider the firmware image |
| * which consists of a 4K header in front of us that contains the IVT, DCD |
| * and some padding thus 'our' max size is really 0x00908000 - 0x00938000 |
| * or 192KB |
| */ |
| #define CONFIG_SPL_MAX_SIZE 0x30000 |
| #define CONFIG_SPL_STACK 0x0093FFB8 |
| /* |
| * Pad SPL to 196KB (4KB header + 192KB max size). This allows to write the |
| * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a |
| * boot media (given that boot media specific offset is configured properly). |
| */ |
| #define CONFIG_SPL_PAD_TO 0x31000 |
| #else |
| /* |
| * see Figure 8-3 in IMX6SDL Reference manuals: |
| * - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF |
| * - BOOT ROM stack is at 0x0091FFB8 |
| * - if icache/dcache is enabled (eFuse/strapping controlled) then the |
| * IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to |
| * fit between 0x00907000 and 0x00918000. |
| * - Additionally the BOOT ROM loads what they consider the firmware image |
| * which consists of a 4K header in front of us that contains the IVT, DCD |
| * and some padding thus 'our' max size is really 0x00908000 - 0x00918000 |
| * or 64KB |
| */ |
| #define CONFIG_SPL_MAX_SIZE 0x10000 |
| #define CONFIG_SPL_STACK 0x0091FFB8 |
| /* |
| * Pad SPL to 68KB (4KB header + 64KB max size). This allows to write the |
| * SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a |
| * boot media (given that boot media specific offset is configured properly). |
| */ |
| #define CONFIG_SPL_PAD_TO 0x11000 |
| |
| #endif |
| |
| /* MMC support */ |
| #if defined(CONFIG_SPL_MMC) |
| #define CONFIG_SYS_MONITOR_LEN 409600 /* 400 KB */ |
| #endif |
| |
| /* SATA support */ |
| #if defined(CONFIG_SPL_SATA) |
| #define CONFIG_SPL_SATA_BOOT_DEVICE 0 |
| #define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1 |
| #endif |
| |
| /* Define the payload for FAT/EXT support */ |
| #if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4) |
| # ifdef CONFIG_OF_CONTROL |
| # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img" |
| # else |
| # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" |
| # endif |
| #endif |
| |
| #if defined(CONFIG_MX6SX) || defined(CONFIG_MX6SL) || \ |
| defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL) |
| #define CONFIG_SPL_BSS_START_ADDR 0x88200000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */ |
| #define CONFIG_SYS_SPL_MALLOC_START 0x88300000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ |
| #else |
| #define CONFIG_SPL_BSS_START_ADDR 0x18200000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */ |
| #define CONFIG_SYS_SPL_MALLOC_START 0x18300000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ |
| #endif |
| #endif |
| |
| #endif |