blob: cd3dd763f7fe2629dc175e39d4a6257d964cfe94 [file] [log] [blame]
/*
* (C) Copyright 2002
* Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* Copied from lubbock.h
*
* (C) Copyright 2004
* BEC Systems <http://bec-systems.com>
* Cliff Brake <cliff.brake@gmail.com>
* Configuation settings for the Accelent/Vibren PXA255 IDP
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/pxa-regs.h>
/*
* If we are developing, we might want to start U-Boot from RAM
* so we MUST NOT initialize critical regs like mem-timing ...
*/
#undef CONFIG_SKIP_LOWLEVEL_INIT /* define for developing */
#define CONFIG_SYS_TEXT_BASE 0x0
/*
* define the following to enable debug blinks. A debug blink function
* must be defined in memsetup.S
*/
#undef DEBUG_BLINK_ENABLE
#undef DEBUG_BLINKC_ENABLE
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_CPU_PXA25X 1 /* This is an PXA250 CPU */
#undef CONFIG_LCD
#ifdef CONFIG_LCD
#define CONFIG_PXA_LCD
#define CONFIG_SHARP_LM8V31
#endif
#define CONFIG_MMC 1
#define CONFIG_DOS_PARTITION 1
#define CONFIG_BOARD_LATE_INIT
/* we will never enable dcache, because we have to setup MMU first */
#define CONFIG_SYS_DCACHE_OFF
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/*
* PXA250 IDP memory map information
*/
#define IDP_CS5_ETH_OFFSET 0x03400000
/*
* Hardware drivers
*/
#define CONFIG_SMC91111
#define CONFIG_SMC91111_BASE (PXA_CS5_PHYS + IDP_CS5_ETH_OFFSET + 0x300)
#define CONFIG_SMC_USE_32_BIT 1
/* #define CONFIG_SMC_USE_IOFUNCS */
/* the following has to be set high -- suspect something is wrong with
* with the tftp timeout routines. FIXME!!!
*/
#define CONFIG_NET_RETRY_COUNT 100
/*
* select serial console configuration
*/
#define CONFIG_PXA_SERIAL
#define CONFIG_FFUART 1 /* we use FFUART on LUBBOCK */
#define CONFIG_CONS_INDEX 3
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_FAT
#define CONFIG_CMD_DHCP
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTCOMMAND "bootm 40000"
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
/* #define CONFIG_INITRD_TAG 1 */
/*
* Current memory map for Vibren supplied Linux images:
*
* Flash:
* 0 - 0x3ffff (size = 0x40000): bootloader
* 0x40000 - 0x13ffff (size = 0x100000): kernel
* 0x140000 - 0x1f3ffff (size = 0x1e00000): jffs
*
* RAM:
* 0xa0008000 - kernel is loaded
* 0xa3000000 - Uboot runs (48MB into RAM)
*
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"prog_boot_mmc=" \
"mw.b 0xa0000000 0xff 0x40000; " \
"if mmcinit && " \
"fatload mmc 0 0xa0000000 u-boot.bin; " \
"then " \
"protect off 0x0 0x3ffff; " \
"erase 0x0 0x3ffff; " \
"cp.b 0xa0000000 0x0 0x40000; " \
"reset;" \
"fi\0" \
"prog_uzImage_mmc=" \
"mw.b 0xa0000000 0xff 0x100000; " \
"if mmcinit && " \
"fatload mmc 0 0xa0000000 uzImage; " \
"then " \
"protect off 0x40000 0xfffff; " \
"erase 0x40000 0xfffff; " \
"cp.b 0xa0000000 0x40000 0x100000; " \
"fi\0" \
"prog_jffs_mmc=" \
"mw.b 0xa0000000 0xff 0x1e00000; " \
"if mmcinit && " \
"fatload mmc 0 0xa0000000 root.jffs; " \
"then " \
"protect off 0x140000 0x1f3ffff; " \
"erase 0x140000 0x1f3ffff; " \
"cp.b 0xa0000000 0x140000 0x1e00000; " \
"fi\0" \
"boot_mmc=" \
"if mmcinit && " \
"fatload mmc 0 0xa1000000 uzImage && " \
"then " \
"bootm 0xa1000000; " \
"fi\0" \
"prog_boot_net=" \
"mw.b 0xa0000000 0xff 0x100000; " \
"if bootp 0xa0000000 u-boot.bin; " \
"then " \
"protect off 0x0 0x3ffff; " \
"erase 0x0 0x3ffff; " \
"cp.b 0xa0000000 0x0 0x40000; " \
"reset; " \
"fi\0" \
"prog_uzImage_net=" \
"mw.b 0xa0000000 0xff 0x100000; " \
"if bootp 0xa0000000 uzImage; " \
"then " \
"protect off 0x40000 0xfffff; " \
"erase 0x40000 0xfffff; " \
"cp.b 0xa0000000 0x40000 0x100000; " \
"fi\0" \
"prog_jffs_net=" \
"mw.b 0xa0000000 0xff 0x1e00000; " \
"if bootp 0xa0000000 root.jffs; " \
"then " \
"protect off 0x140000 0x1f3ffff; " \
"erase 0x140000 0x1f3ffff; " \
"cp.b 0xa0000000 0x140000 0x1e00000; " \
"fi\0"
/* "erase_env=" */
/* "protect off" */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER 1
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT "$ " /* Monitor Command Prompt */
#else
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#endif
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_DEVICE_NULLDEV 1
#define CONFIG_SYS_MEMTEST_START 0xa0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0xa0800000 /* default load address */
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */
#define RTC 1 /* enable 32KHz osc */
#ifdef CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_PXA_MMC_GENERIC
#define CONFIG_CMD_MMC
#define CONFIG_SYS_MMC_BASE 0xF0000000
#endif
/*
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */
#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */
#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */
#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */
#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */
#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */
#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */
#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */
#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */
#define CONFIG_SYS_DRAM_BASE 0xa0000000
#define CONFIG_SYS_DRAM_SIZE 0x04000000
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR 0xfffff800
/*
* GPIO settings
*/
#define CONFIG_SYS_GAFR0_L_VAL 0x80001005
#define CONFIG_SYS_GAFR0_U_VAL 0xa5128012
#define CONFIG_SYS_GAFR1_L_VAL 0x699a9558
#define CONFIG_SYS_GAFR1_U_VAL 0xaaa5aa6a
#define CONFIG_SYS_GAFR2_L_VAL 0xaaaaaaaa
#define CONFIG_SYS_GAFR2_U_VAL 0x2
#define CONFIG_SYS_GPCR0_VAL 0x1800400
#define CONFIG_SYS_GPCR1_VAL 0x0
#define CONFIG_SYS_GPCR2_VAL 0x0
#define CONFIG_SYS_GPDR0_VAL 0xc1818440
#define CONFIG_SYS_GPDR1_VAL 0xfcffab82
#define CONFIG_SYS_GPDR2_VAL 0x1ffff
#define CONFIG_SYS_GPSR0_VAL 0x8000
#define CONFIG_SYS_GPSR1_VAL 0x3f0002
#define CONFIG_SYS_GPSR2_VAL 0x1c000
#define CONFIG_SYS_PSSR_VAL 0x20
#define CONFIG_SYS_CCCR CCCR_L27|CCCR_M2|CCCR_N10
#define CONFIG_SYS_CKEN 0x0
/*
* Memory settings
*/
#define CONFIG_SYS_MSC0_VAL 0x29DCA4D2
#define CONFIG_SYS_MSC1_VAL 0x43AC494C
#define CONFIG_SYS_MSC2_VAL 0x39D449D4
#define CONFIG_SYS_MDCNFG_VAL 0x090009C9
#define CONFIG_SYS_MDREFR_VAL 0x0085C017
#define CONFIG_SYS_MDMRS_VAL 0x00220022
#define CONFIG_SYS_FLYCNFG_VAL 0x00000000
#define CONFIG_SYS_SXCNFG_VAL 0x00000000
/*
* PCMCIA and CF Interfaces
*/
#define CONFIG_SYS_MECR_VAL 0x00000003
#define CONFIG_SYS_MCMEM0_VAL 0x00014405
#define CONFIG_SYS_MCMEM1_VAL 0x00014405
#define CONFIG_SYS_MCATT0_VAL 0x00014405
#define CONFIG_SYS_MCATT1_VAL 0x00014405
#define CONFIG_SYS_MCIO0_VAL 0x00014405
#define CONFIG_SYS_MCIO1_VAL 0x00014405
/*
* FLASH and environment organization
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_MONITOR_BASE 0
#define CONFIG_SYS_MONITOR_LEN PHYS_FLASH_SECT_SIZE
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
/* timeout values are in ticks */
#define CONFIG_SYS_FLASH_ERASE_TOUT (25*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
#define CONFIG_SYS_FLASH_WRITE_TOUT (25*CONFIG_SYS_HZ) /* Timeout for Flash Write */
/* put cfg at end of flash for now */
#define CONFIG_ENV_IS_IN_FLASH 1
/* Addr of Environment Sector */
#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SIZE - 0x40000)
#define CONFIG_ENV_SIZE PHYS_FLASH_SECT_SIZE /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE (PHYS_FLASH_SECT_SIZE / 16)
#endif /* __CONFIG_H */