| /* |
| * -- Version 1.1 -- |
| * |
| * (C) Copyright 2003-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2004-2005 |
| * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de |
| * |
| * (C) Copyright 2005 |
| * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de. |
| * |
| * History: |
| * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ |
| #define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */ |
| #define CONFIG_TQM5200 1 /* ... on a TQM5200 module */ |
| |
| #define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ |
| #define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ |
| #define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ |
| #define CONFIG_BC3450_USB 1 /* + USB support */ |
| # define CONFIG_FAT 1 /* + FAT support */ |
| # define CONFIG_EXT2 1 /* + EXT2 support */ |
| #undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */ |
| #undef CONFIG_BC3450_CAN /* + CAN transceiver */ |
| #undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */ |
| #undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ |
| #undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ |
| #define CONFIG_BC3450_FP 1 /* + enable FP O/P */ |
| #undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */ |
| |
| #define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ |
| |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ |
| #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * AT-PS/2 Multiplexer |
| */ |
| #ifdef CONFIG_BC3450_PS2 |
| # define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ |
| # define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ |
| # define CONFIG_PS2SERIAL 6 /* .. on PSC6 */ |
| # define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */ |
| # define CONFIG_BOARD_EARLY_INIT_R |
| #endif /* CONFIG_BC3450_PS2 */ |
| |
| /* |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| */ |
| # define CONFIG_PCI 1 |
| # define CONFIG_PCI_PNP 1 |
| /* #define CONFIG_PCI_SCAN_SHOW 1 */ |
| #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 |
| |
| #define CONFIG_PCI_MEM_BUS 0x40000000 |
| #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| #define CONFIG_PCI_MEM_SIZE 0x10000000 |
| |
| #define CONFIG_PCI_IO_BUS 0x50000000 |
| #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| #define CONFIG_PCI_IO_SIZE 0x01000000 |
| |
| #define CONFIG_NET_MULTI 1 |
| /*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */ |
| #define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ |
| #define CONFIG_NS8382X 1 |
| |
| /* |
| * Video console |
| */ |
| # define CONFIG_VIDEO |
| # define CONFIG_VIDEO_SM501 |
| # define CONFIG_VIDEO_SM501_32BPP |
| # define CONFIG_CFB_CONSOLE |
| # define CONFIG_VIDEO_LOGO |
| # define CONFIG_VGA_AS_SINGLE_DEVICE |
| # define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */ |
| # define CONFIG_VIDEO_SW_CURSOR |
| # define CONFIG_SPLASH_SCREEN |
| # define CFG_CONSOLE_IS_IN_ENV |
| |
| /* |
| * Partitions |
| */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| /* |
| * USB |
| */ |
| #ifdef CONFIG_BC3450_USB |
| # define CONFIG_USB_OHCI |
| # define CONFIG_USB_STORAGE |
| #endif /* CONFIG_BC3450_USB */ |
| |
| /* |
| * POST support |
| */ |
| #define CONFIG_POST (CFG_POST_MEMORY | \ |
| CFG_POST_CPU | \ |
| CFG_POST_I2C) |
| |
| #ifdef CONFIG_POST |
| /* preserve space for the post_word at end of on-chip SRAM */ |
| # define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 |
| #endif /* CONFIG_POST */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_SNTP |
| #define CONFIG_CMD_BSP |
| |
| #ifdef CONFIG_VIDEO |
| #define CONFIG_CMD_BMP |
| #endif |
| |
| #ifdef CONFIG_BC3450_IDE |
| #define CONFIG_CMD_IDE |
| #endif |
| |
| #if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB) |
| #ifdef CONFIG_FAT |
| #define CONFIG_CMD_FAT |
| #endif |
| |
| #ifdef CONFIG_EXT2 |
| #define CONFIG_CMD_EXT2 |
| #endif |
| #endif |
| |
| #ifdef CONFIG_BC3450_USB |
| #define CONFIG_CMD_USB |
| #endif |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #ifdef CONFIG_POST |
| #define CONFIG_CMD_DIAG |
| #endif |
| |
| |
| #define CONFIG_TIMESTAMP /* display image timestamps */ |
| |
| #if (TEXT_BASE == 0xFC000000) /* Boot low */ |
| # define CFG_LOWBOOT 1 |
| #endif |
| |
| /* |
| * Autobooting |
| */ |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ |
| "echo;" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "ipaddr=192.168.1.10\0" \ |
| "serverip=192.168.1.3\0" \ |
| "netmask=255.255.255.0\0" \ |
| "hostname=bc3450\0" \ |
| "rootpath=/opt/eldk/ppc_6xx\0" \ |
| "kernel_addr=fc0a0000\0" \ |
| "ramdisk_addr=fc1c0000\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$(serverip):$(rootpath)\0" \ |
| "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ |
| "addip=setenv bootargs $(bootargs) " \ |
| "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ |
| ":$(hostname):$(netdev):off panic=1\0" \ |
| "addcons=setenv bootargs $(bootargs) " \ |
| "console=ttyS0,$(baudrate) console=tty0\0" \ |
| "flash_self=run ramargs addip addcons;" \ |
| "bootm $(kernel_addr) $(ramdisk_addr)\0" \ |
| "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \ |
| "net_nfs=tftp 200000 $(bootfile); " \ |
| "run nfsargs addip addcons; bootm\0" \ |
| "ide_nfs=run nfsargs addip addcons; " \ |
| "disk 200000 0:1; bootm\0" \ |
| "ide_ide=run ideargs addip addcons; " \ |
| "disk 200000 0:1; bootm\0" \ |
| "usb_self=run usbload; run ramargs addip addcons; " \ |
| "bootm 200000 400000\0" \ |
| "usbload=usb reset; usb scan; usbboot 200000 0:1; " \ |
| "usbboot 400000 0:2\0" \ |
| "bootfile=uImage\0" \ |
| "load=tftp 200000 $(u-boot)\0" \ |
| "u-boot=u-boot.bin\0" \ |
| "update=protect off FC000000 FC05FFFF;" \ |
| "erase FC000000 FC05FFFF;" \ |
| "cp.b 200000 FC000000 $(filesize);" \ |
| "protect on FC000000 FC05FFFF\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run flash_self" |
| |
| /* |
| * IPB Bus clocking configuration. |
| */ |
| #define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| /* |
| * PCI Bus clocking configuration |
| * |
| * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if |
| * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock |
| * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. |
| */ |
| #if defined(CFG_IPBCLK_EQUALS_XLBCLK) |
| # define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ |
| #endif |
| |
| /* |
| * I2C configuration |
| */ |
| #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ |
| #define CFG_I2C_MODULE 2 /* Select I2C module #2 */ |
| |
| /* |
| * I2C clock frequency |
| * |
| * Please notice, that the resulting clock frequency could differ from the |
| * configured value. This is because the I2C clock is derived from system |
| * clock over a frequency divider with only a few divider values. U-boot |
| * calculates the best approximation for CFG_I2C_SPEED. However the calculated |
| * approximation allways lies below the configured value, never above. |
| */ |
| #define CFG_I2C_SPEED 100000 /* 100 kHz */ |
| #define CFG_I2C_SLAVE 0x7F |
| |
| /* |
| * EEPROM configuration for I²C EEPROM M24C32 |
| * M24C64 should work also. For other EEPROMs config should be verified. |
| * |
| * The TQM5200 module may hold an EEPROM at address 0x50. |
| */ |
| #define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */ |
| #define CFG_I2C_EEPROM_ADDR_LEN 2 |
| #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ |
| #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70 |
| |
| /* |
| * RTC configuration |
| */ |
| #if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231) |
| # define CONFIG_RTC_M41T11 1 |
| # define CFG_I2C_RTC_ADDR 0x68 |
| #else |
| # define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */ |
| # define CONFIG_BOARD_EARLY_INIT_R |
| #endif |
| |
| /* |
| * Flash configuration |
| */ |
| #define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ |
| |
| /* use CFI flash driver if no module variant is spezified */ |
| #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ |
| #define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } |
| #define CFG_FLASH_EMPTY_INFO |
| #define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ |
| #define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ |
| #undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ |
| |
| #if !defined(CFG_LOWBOOT) |
| #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) |
| #else /* CFG_LOWBOOT */ |
| #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) |
| #endif /* CFG_LOWBOOT */ |
| #define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks |
| (= chip selects) */ |
| #define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ |
| |
| /* Dynamic MTD partition support */ |
| #define CONFIG_JFFS2_CMDLINE |
| #define MTDIDS_DEFAULT "nor0=TQM5200-0" |
| #define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ |
| "1408k(kernel)," \ |
| "2m(initrd)," \ |
| "4m(small-fs)," \ |
| "16m(big-fs)," \ |
| "8m(misc)" |
| |
| /* |
| * Environment settings |
| */ |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_SIZE 0x10000 |
| #define CFG_ENV_SECT_SIZE 0x20000 |
| #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) |
| #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) |
| |
| /* |
| * Memory map |
| */ |
| #define CFG_MBAR 0xF0000000 |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_DEFAULT_MBAR 0x80000000 |
| |
| /* Use ON-Chip SRAM until RAM will be available */ |
| #define CFG_INIT_RAM_ADDR MPC5XXX_SRAM |
| #ifdef CONFIG_POST |
| /* preserve space for the post_word at end of on-chip SRAM */ |
| # define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE |
| #else |
| # define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE |
| #endif /*CONFIG_POST*/ |
| |
| #define CFG_GBL_DATA_SIZE 128 /* Bytes reserved for initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| #define CFG_MONITOR_BASE TEXT_BASE |
| #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) |
| # define CFG_RAMBOOT 1 |
| #endif |
| |
| #define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ |
| #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Ethernet configuration |
| * |
| * Define CONFIG_FEC10MBIT to force FEC at 10MBIT |
| */ |
| #define CONFIG_MPC5xxx_FEC 1 |
| #undef CONFIG_FEC_10MBIT |
| #define CONFIG_PHY_ADDR 0x00 |
| |
| /* |
| * GPIO configuration on BC3450 |
| * |
| * PSC1: UART1 (Service-UART) [0x xxxxxxx4] |
| * PSC2: UART2 [0x xxxxxx4x] |
| * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] |
| * PSC3: USB2 [0x xxxxx1xx] |
| * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] |
| * (this has to match |
| * CONFIG_USB_CONFIG which is |
| * used by usb_ohci.c to set |
| * the USB ports) |
| * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] |
| * (this is reset to '5' |
| * in FEC driver: fec.c) |
| * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] |
| * ATA/CS: ??? [0x x1xxxxxx] |
| * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] |
| * CS1: Use Pin gpio_wkup_6 as second |
| * SDRAM chip select (mem_cs1) |
| * Timer: CAN2 / SPI |
| * I2C: CAN1 / I²C2 [0x bxxxxxxx] |
| */ |
| #ifdef CONFIG_BC3450_AC97 |
| # define CFG_GPS_PORT_CONFIG 0xb1502124 |
| #else /* PSC2=UART2 */ |
| # define CFG_GPS_PORT_CONFIG 0xb1502144 |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max no of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Arg. Buffer Size */ |
| |
| #define CFG_ALT_MEMTEST /* Enable an alternative, */ |
| /* more extensive mem test */ |
| |
| #define CFG_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CFG_HZ 1000 /* dec freq: 1ms ticks */ |
| |
| #define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * Enable loopw command. |
| */ |
| #define CONFIG_LOOPW |
| |
| /* |
| * Various low-level settings |
| */ |
| #if defined(CONFIG_MPC5200) |
| # define CFG_HID0_INIT HID0_ICE | HID0_ICFI |
| # define CFG_HID0_FINAL HID0_ICE |
| #else |
| # define CFG_HID0_INIT 0 |
| # define CFG_HID0_FINAL 0 |
| #endif |
| |
| #define CFG_BOOTCS_START CFG_FLASH_BASE |
| #define CFG_BOOTCS_SIZE CFG_FLASH_SIZE |
| #ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 |
| # define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ |
| #else |
| # define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ |
| #endif |
| #define CFG_CS0_START CFG_FLASH_BASE |
| #define CFG_CS0_SIZE CFG_FLASH_SIZE |
| |
| /* automatic configuration of chip selects */ |
| #ifdef CONFIG_TQM5200 |
| # define CONFIG_LAST_STAGE_INIT |
| #endif /* CONFIG_TQM5200 */ |
| |
| /* |
| * SRAM - Do not map below 2 GB in address space, because this area is used |
| * for SDRAM autosizing. |
| */ |
| #ifdef CONFIG_TQM5200 |
| # define CFG_CS2_START 0xE5000000 |
| # define CFG_CS2_SIZE 0x100000 /* 1 MByte */ |
| # define CFG_CS2_CFG 0x0004D930 |
| #endif /* CONFIG_TQM5200 */ |
| |
| /* |
| * Grafic controller - Do not map below 2 GB in address space, because this |
| * area is used for SDRAM autosizing. |
| */ |
| #ifdef CONFIG_TQM5200 |
| # define SM501_FB_BASE 0xE0000000 |
| # define CFG_CS1_START (SM501_FB_BASE) |
| # define CFG_CS1_SIZE 0x4000000 /* 64 MByte */ |
| # define CFG_CS1_CFG 0x8F48FF70 |
| # define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000 |
| #endif /* CONFIG_TQM5200 */ |
| |
| #define CFG_CS_BURST 0x00000000 |
| #define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */ |
| /* flash and SM501 */ |
| |
| #define CFG_RESET_ADDRESS 0xff000000 |
| |
| /* |
| * USB stuff |
| */ |
| #define CONFIG_USB_CLOCK 0x0001BBBB |
| #define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ |
| |
| /* |
| * IDE/ATA stuff Supports IDE harddisk |
| */ |
| #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| |
| #define CONFIG_IDE_RESET /* reset for ide supported */ |
| #define CONFIG_IDE_PREINIT |
| |
| #define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ |
| |
| #define CFG_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CFG_ATA_BASE_ADDR MPC5XXX_ATA |
| |
| /* Offset for data I/O */ |
| #define CFG_ATA_DATA_OFFSET (0x0060) |
| |
| /* Offset for normal register accesses */ |
| #define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) |
| |
| /* Offset for alternate registers */ |
| #define CFG_ATA_ALT_OFFSET (0x005C) |
| |
| /* Interval between registers */ |
| #define CFG_ATA_STRIDE 4 |
| |
| #endif /* __CONFIG_H */ |