blob: 98fe7bc3bcb169d04a1d0770bbdb7dc8e1153b19 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Qualcomm EHCI driver
*
* (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
*
* Based on Linux driver
*/
#include <common.h>
#include <dm.h>
#include <dm/lists.h>
#include <errno.h>
#include <usb.h>
#include <usb/ehci-ci.h>
#include <usb/ulpi.h>
#include <wait_bit.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <linux/compat.h>
#include "ehci.h"
struct msm_ehci_priv {
struct ehci_ctrl ctrl; /* Needed by EHCI */
struct usb_ehci *ehci; /* Start of IP core*/
struct ulpi_viewport ulpi_vp; /* ULPI Viewport */
struct phy phy;
};
static int msm_init_after_reset(struct ehci_ctrl *dev)
{
struct msm_ehci_priv *p = container_of(dev, struct msm_ehci_priv, ctrl);
struct usb_ehci *ehci = p->ehci;
generic_phy_reset(&p->phy);
/* set mode to host controller */
writel(CM_HOST, &ehci->usbmode);
return 0;
}
static const struct ehci_ops msm_ehci_ops = {
.init_after_reset = msm_init_after_reset
};
static int ehci_usb_probe(struct udevice *dev)
{
struct msm_ehci_priv *p = dev_get_priv(dev);
struct usb_ehci *ehci = p->ehci;
struct usb_plat *plat = dev_get_plat(dev);
struct ehci_hccr *hccr;
struct ehci_hcor *hcor;
int ret;
hccr = (struct ehci_hccr *)((phys_addr_t)&ehci->caplength);
hcor = (struct ehci_hcor *)((phys_addr_t)hccr +
HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
ret = generic_setup_phy(dev, &p->phy, 0);
if (ret)
return ret;
ret = board_usb_init(0, plat->init_type);
if (ret < 0)
return ret;
return ehci_register(dev, hccr, hcor, &msm_ehci_ops, 0,
plat->init_type);
}
static int ehci_usb_remove(struct udevice *dev)
{
struct msm_ehci_priv *p = dev_get_priv(dev);
struct usb_ehci *ehci = p->ehci;
int ret;
ret = ehci_deregister(dev);
if (ret)
return ret;
/* Stop controller. */
clrbits_le32(&ehci->usbcmd, CMD_RUN);
ret = generic_shutdown_phy(&p->phy);
if (ret)
return ret;
ret = board_usb_init(0, USB_INIT_DEVICE); /* Board specific hook */
if (ret < 0)
return ret;
/* Reset controller */
setbits_le32(&ehci->usbcmd, CMD_RESET);
/* Wait for reset */
if (wait_for_bit_le32(&ehci->usbcmd, CMD_RESET, false, 30, false)) {
printf("Stuck on USB reset.\n");
return -ETIMEDOUT;
}
return 0;
}
static int ehci_usb_of_to_plat(struct udevice *dev)
{
struct msm_ehci_priv *priv = dev_get_priv(dev);
priv->ulpi_vp.port_num = 0;
priv->ehci = dev_read_addr_ptr(dev);
if (priv->ehci == (void *)FDT_ADDR_T_NONE)
return -EINVAL;
/* Warning: this will not work if viewport address is > 64 bit due to
* ULPI design.
*/
priv->ulpi_vp.viewport_addr = (phys_addr_t)&priv->ehci->ulpi_viewpoint;
return 0;
}
static int ehci_usb_of_bind(struct udevice *dev)
{
ofnode ulpi_node = ofnode_first_subnode(dev_ofnode(dev));
ofnode phy_node;
if (!ofnode_valid(ulpi_node))
return 0;
phy_node = ofnode_first_subnode(ulpi_node);
if (!ofnode_valid(phy_node)) {
printf("%s: ulpi subnode with no phy\n", __func__);
return -ENOENT;
}
return device_bind_driver_to_node(dev, "msm8916_usbphy", "msm8916_usbphy",
phy_node, NULL);
}
#if defined(CONFIG_CI_UDC)
/* Little quirk that MSM needs with Chipidea controller
* Must reinit phy after reset
*/
void ci_init_after_reset(struct ehci_ctrl *ctrl)
{
struct msm_ehci_priv *p = ctrl->priv;
generic_phy_reset(&p->phy);
}
#endif
static const struct udevice_id ehci_usb_ids[] = {
{ .compatible = "qcom,ci-hdrc", },
{ }
};
U_BOOT_DRIVER(usb_ehci) = {
.name = "ehci_msm",
.id = UCLASS_USB,
.of_match = ehci_usb_ids,
.of_to_plat = ehci_usb_of_to_plat,
.bind = ehci_usb_of_bind,
.probe = ehci_usb_probe,
.remove = ehci_usb_remove,
.ops = &ehci_usb_ops,
.priv_auto = sizeof(struct msm_ehci_priv),
.plat_auto = sizeof(struct usb_plat),
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};