| /* |
| * config-pre.h - common defines for Blackfin boards in config.h |
| * |
| * Copyright (c) 2007-2009 Analog Devices Inc. |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #ifndef __ASM_BLACKFIN_CONFIG_PRE_H__ |
| #define __ASM_BLACKFIN_CONFIG_PRE_H__ |
| |
| /* Misc helper functions */ |
| #define XMK_STR(x) #x |
| #define MK_STR(x) XMK_STR(x) |
| #define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0])) |
| |
| /* Bootmode defines -- your config needs to select this via CONFIG_BFIN_BOOT_MODE. |
| * Depending on your cpu, some of these may not be valid, check your HRM. |
| * The actual values here are meaningless as long as they're unique. |
| */ |
| #define BFIN_BOOT_BYPASS 1 /* bypass bootrom */ |
| #define BFIN_BOOT_PARA 2 /* boot ldr out of parallel flash */ |
| #define BFIN_BOOT_SPI_MASTER 3 /* boot ldr out of serial flash */ |
| #define BFIN_BOOT_SPI_SLAVE 4 /* boot ldr as spi slave */ |
| #define BFIN_BOOT_TWI_MASTER 5 /* boot ldr over twi device */ |
| #define BFIN_BOOT_TWI_SLAVE 6 /* boot ldr over twi slave */ |
| #define BFIN_BOOT_UART 7 /* boot ldr over uart */ |
| #define BFIN_BOOT_IDLE 8 /* do nothing, just idle */ |
| #define BFIN_BOOT_FIFO 9 /* boot ldr out of FIFO */ |
| #define BFIN_BOOT_MEM 10 /* boot ldr out of memory (warmboot) */ |
| #define BFIN_BOOT_16HOST_DMA 11 /* boot ldr from 16-bit host dma */ |
| #define BFIN_BOOT_8HOST_DMA 12 /* boot ldr from 8-bit host dma */ |
| #define BFIN_BOOT_NAND 13 /* boot ldr from nand flash */ |
| |
| #ifndef __ASSEMBLY__ |
| static inline const char *get_bfin_boot_mode(int bfin_boot) |
| { |
| switch (bfin_boot) { |
| case BFIN_BOOT_BYPASS: return "bypass"; |
| case BFIN_BOOT_PARA: return "parallel flash"; |
| case BFIN_BOOT_SPI_MASTER: return "spi flash"; |
| case BFIN_BOOT_SPI_SLAVE: return "spi slave"; |
| case BFIN_BOOT_TWI_MASTER: return "i2c flash"; |
| case BFIN_BOOT_TWI_SLAVE: return "i2c slave"; |
| case BFIN_BOOT_UART: return "uart"; |
| case BFIN_BOOT_IDLE: return "idle"; |
| case BFIN_BOOT_FIFO: return "fifo"; |
| case BFIN_BOOT_MEM: return "memory"; |
| case BFIN_BOOT_16HOST_DMA: return "16bit dma"; |
| case BFIN_BOOT_8HOST_DMA: return "8bit dma"; |
| case BFIN_BOOT_NAND: return "nand flash"; |
| default: return "INVALID"; |
| } |
| } |
| #endif |
| |
| /* Most bootroms allow for EVT1 redirection */ |
| #if ((defined(__ADSPBF531__) || defined(__ADSPBF532__) || defined(__ADSPBF533__)) \ |
| && __SILICON_REVISION__ < 3) || defined(__ADSPBF561__) |
| # undef CONFIG_BFIN_BOOTROM_USES_EVT1 |
| #else |
| # define CONFIG_BFIN_BOOTROM_USES_EVT1 |
| #endif |
| |
| /* Define the default SPI CS used when booting out of SPI */ |
| #if defined(__ADSPBF531__) || defined(__ADSPBF532__) || defined(__ADSPBF533__) || \ |
| defined(__ADSPBF538__) || defined(__ADSPBF539__) || defined(__ADSPBF561__) || \ |
| defined(__ADSPBF51x__) |
| # define BFIN_BOOT_SPI_SSEL 2 |
| #else |
| # define BFIN_BOOT_SPI_SSEL 1 |
| #endif |
| |
| /* There is no Blackfin/NetBSD port */ |
| #undef CONFIG_BOOTM_NETBSD |
| |
| /* We rarely use interrupts, so favor throughput over latency */ |
| #define CONFIG_BFIN_INS_LOWOVERHEAD |
| |
| #endif |