blob: 26c014cc4f73ec4168b56049f7d5f70ad7a8c66b [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Driver for IDT Versaclock 5/6
*
* Derived from code Copyright (C) 2017 Marek Vasut <marek.vasut@gmail.com>
*/
#include <common.h>
#include <clk.h>
#include <clk-uclass.h>
#include <dm.h>
#include <errno.h>
#include <i2c.h>
#include <dm/device_compat.h>
#include <log.h>
#include <linux/clk-provider.h>
#include <linux/kernel.h>
#include <linux/math64.h>
#include <dt-bindings/clk/versaclock.h>
/* VersaClock5 registers */
#define VC5_OTP_CONTROL 0x00
/* Factory-reserved register block */
#define VC5_RSVD_DEVICE_ID 0x01
#define VC5_RSVD_ADC_GAIN_7_0 0x02
#define VC5_RSVD_ADC_GAIN_15_8 0x03
#define VC5_RSVD_ADC_OFFSET_7_0 0x04
#define VC5_RSVD_ADC_OFFSET_15_8 0x05
#define VC5_RSVD_TEMPY 0x06
#define VC5_RSVD_OFFSET_TBIN 0x07
#define VC5_RSVD_GAIN 0x08
#define VC5_RSVD_TEST_NP 0x09
#define VC5_RSVD_UNUSED 0x0a
#define VC5_RSVD_BANDGAP_TRIM_UP 0x0b
#define VC5_RSVD_BANDGAP_TRIM_DN 0x0c
#define VC5_RSVD_CLK_R_12_CLK_AMP_4 0x0d
#define VC5_RSVD_CLK_R_34_CLK_AMP_4 0x0e
#define VC5_RSVD_CLK_AMP_123 0x0f
/* Configuration register block */
#define VC5_PRIM_SRC_SHDN 0x10
#define VC5_PRIM_SRC_SHDN_EN_XTAL BIT(7)
#define VC5_PRIM_SRC_SHDN_EN_CLKIN BIT(6)
#define VC5_PRIM_SRC_SHDN_EN_DOUBLE_XTAL_FREQ BIT(3)
#define VC5_PRIM_SRC_SHDN_SP BIT(1)
#define VC5_PRIM_SRC_SHDN_EN_GBL_SHDN BIT(0)
#define VC5_VCO_BAND 0x11
#define VC5_XTAL_X1_LOAD_CAP 0x12
#define VC5_XTAL_X2_LOAD_CAP 0x13
#define VC5_REF_DIVIDER 0x15
#define VC5_REF_DIVIDER_SEL_PREDIV2 BIT(7)
#define VC5_REF_DIVIDER_REF_DIV(n) ((n) & 0x3f)
#define VC5_VCO_CTRL_AND_PREDIV 0x16
#define VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV BIT(7)
#define VC5_FEEDBACK_INT_DIV 0x17
#define VC5_FEEDBACK_INT_DIV_BITS 0x18
#define VC5_FEEDBACK_FRAC_DIV(n) (0x19 + (n))
#define VC5_RC_CONTROL0 0x1e
#define VC5_RC_CONTROL1 0x1f
/* Register 0x20 is factory reserved */
/* Output divider control for divider 1,2,3,4 */
#define VC5_OUT_DIV_CONTROL(idx) (0x21 + ((idx) * 0x10))
#define VC5_OUT_DIV_CONTROL_RESET BIT(7)
#define VC5_OUT_DIV_CONTROL_SELB_NORM BIT(3)
#define VC5_OUT_DIV_CONTROL_SEL_EXT BIT(2)
#define VC5_OUT_DIV_CONTROL_INT_MODE BIT(1)
#define VC5_OUT_DIV_CONTROL_EN_FOD BIT(0)
#define VC5_OUT_DIV_FRAC(idx, n) (0x22 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_FRAC4_OD_SCEE BIT(1)
#define VC5_OUT_DIV_STEP_SPREAD(idx, n) (0x26 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SPREAD_MOD(idx, n) (0x29 + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SKEW_INT(idx, n) (0x2b + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_INT(idx, n) (0x2d + ((idx) * 0x10) + (n))
#define VC5_OUT_DIV_SKEW_FRAC(idx) (0x2f + ((idx) * 0x10))
/* Registers 0x30, 0x40, 0x50 are factory reserved */
/* Clock control register for clock 1,2 */
#define VC5_CLK_OUTPUT_CFG(idx, n) (0x60 + ((idx) * 0x2) + (n))
#define VC5_CLK_OUTPUT_CFG0_CFG_SHIFT 5
#define VC5_CLK_OUTPUT_CFG0_CFG_MASK GENMASK(7, VC5_CLK_OUTPUT_CFG0_CFG_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_CFG_LVPECL (VC5_LVPECL)
#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS (VC5_CMOS)
#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL33 (VC5_HCSL33)
#define VC5_CLK_OUTPUT_CFG0_CFG_LVDS (VC5_LVDS)
#define VC5_CLK_OUTPUT_CFG0_CFG_CMOS2 (VC5_CMOS2)
#define VC5_CLK_OUTPUT_CFG0_CFG_CMOSD (VC5_CMOSD)
#define VC5_CLK_OUTPUT_CFG0_CFG_HCSL25 (VC5_HCSL25)
#define VC5_CLK_OUTPUT_CFG0_PWR_SHIFT 3
#define VC5_CLK_OUTPUT_CFG0_PWR_MASK GENMASK(4, VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_PWR_18 (0 << VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_PWR_25 (2 << VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_PWR_33 (3 << VC5_CLK_OUTPUT_CFG0_PWR_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT 0
#define VC5_CLK_OUTPUT_CFG0_SLEW_MASK GENMASK(1, VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_SLEW_80 (0 << VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_SLEW_85 (1 << VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_SLEW_90 (2 << VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
#define VC5_CLK_OUTPUT_CFG0_SLEW_100 (3 << VC5_CLK_OUTPUT_CFG0_SLEW_SHIFT)
#define VC5_CLK_OUTPUT_CFG1_EN_CLKBUF BIT(0)
#define VC5_CLK_OE_SHDN 0x68
#define VC5_CLK_OS_SHDN 0x69
#define VC5_GLOBAL_REGISTER 0x76
#define VC5_GLOBAL_REGISTER_GLOBAL_RESET BIT(5)
/* PLL/VCO runs between 2.5 GHz and 3.0 GHz */
#define VC5_PLL_VCO_MIN 2500000000UL
#define VC5_PLL_VCO_MAX 3000000000UL
/* VC5 Input mux settings */
#define VC5_MUX_IN_XIN BIT(0)
#define VC5_MUX_IN_CLKIN BIT(1)
/* Maximum number of clk_out supported by this driver */
#define VC5_MAX_CLK_OUT_NUM 5
/* Maximum number of FODs supported by this driver */
#define VC5_MAX_FOD_NUM 4
/* flags to describe chip features */
/* chip has built-in oscilator */
#define VC5_HAS_INTERNAL_XTAL BIT(0)
/* chip has PFD requency doubler */
#define VC5_HAS_PFD_FREQ_DBL BIT(1)
/* Supported IDT VC5 models. */
enum vc5_model {
IDT_VC5_5P49V5923,
IDT_VC5_5P49V5925,
IDT_VC5_5P49V5933,
IDT_VC5_5P49V5935,
IDT_VC6_5P49V6901,
IDT_VC6_5P49V6965,
};
/* Structure to describe features of a particular VC5 model */
struct vc5_chip_info {
const enum vc5_model model;
const unsigned int clk_fod_cnt;
const unsigned int clk_out_cnt;
const u32 flags;
};
struct vc5_driver_data;
struct vc5_hw_data {
struct clk hw;
struct vc5_driver_data *vc5;
u32 div_int;
u32 div_frc;
unsigned int num;
};
struct vc5_out_data {
struct clk hw;
struct vc5_driver_data *vc5;
unsigned int num;
unsigned int clk_output_cfg0;
unsigned int clk_output_cfg0_mask;
};
struct vc5_driver_data {
struct udevice *i2c;
const struct vc5_chip_info *chip_info;
struct clk *pin_xin;
struct clk *pin_clkin;
unsigned char clk_mux_ins;
struct clk clk_mux;
struct clk clk_mul;
struct clk clk_pfd;
struct vc5_hw_data clk_pll;
struct vc5_hw_data clk_fod[VC5_MAX_FOD_NUM];
struct vc5_out_data clk_out[VC5_MAX_CLK_OUT_NUM];
};
static const struct vc5_chip_info idt_5p49v5923_info = {
.model = IDT_VC5_5P49V5923,
.clk_fod_cnt = 2,
.clk_out_cnt = 3,
.flags = 0,
};
static const struct vc5_chip_info idt_5p49v5925_info = {
.model = IDT_VC5_5P49V5925,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = 0,
};
static const struct vc5_chip_info idt_5p49v5933_info = {
.model = IDT_VC5_5P49V5933,
.clk_fod_cnt = 2,
.clk_out_cnt = 3,
.flags = VC5_HAS_INTERNAL_XTAL,
};
static const struct vc5_chip_info idt_5p49v5935_info = {
.model = IDT_VC5_5P49V5935,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = VC5_HAS_INTERNAL_XTAL,
};
static const struct vc5_chip_info idt_5p49v6901_info = {
.model = IDT_VC6_5P49V6901,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = VC5_HAS_PFD_FREQ_DBL,
};
static const struct vc5_chip_info idt_5p49v6965_info = {
.model = IDT_VC6_5P49V6965,
.clk_fod_cnt = 4,
.clk_out_cnt = 5,
.flags = 0,
};
static int vc5_update_bits(struct udevice *dev, unsigned int reg, unsigned int mask,
unsigned int src)
{
int ret;
unsigned char cache;
ret = dm_i2c_read(dev, reg, &cache, 1);
if (ret < 0)
return ret;
cache &= ~mask;
cache |= mask & src;
ret = dm_i2c_write(dev, reg, (uchar *)&cache, 1);
return ret;
}
static unsigned long vc5_mux_get_rate(struct clk *hw)
{
return clk_get_rate(clk_get_parent(hw));
}
static int vc5_mux_set_parent(struct clk *hw, unsigned char index)
{
struct vc5_driver_data *vc5 = container_of(hw, struct vc5_driver_data, clk_mux);
const u8 mask = VC5_PRIM_SRC_SHDN_EN_XTAL | VC5_PRIM_SRC_SHDN_EN_CLKIN;
u8 src;
if (index > 1 || !vc5->clk_mux_ins)
return -EINVAL;
if (vc5->clk_mux_ins == (VC5_MUX_IN_CLKIN | VC5_MUX_IN_XIN)) {
if (index == 0)
src = VC5_PRIM_SRC_SHDN_EN_XTAL;
if (index == 1)
src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
} else {
if (index != 0)
return -EINVAL;
if (vc5->clk_mux_ins == VC5_MUX_IN_XIN)
src = VC5_PRIM_SRC_SHDN_EN_XTAL;
else if (vc5->clk_mux_ins == VC5_MUX_IN_CLKIN)
src = VC5_PRIM_SRC_SHDN_EN_CLKIN;
else /* Invalid; should have been caught by vc5_probe() */
return -EINVAL;
}
return vc5_update_bits(vc5->i2c, VC5_PRIM_SRC_SHDN, mask, src);
}
static const struct clk_ops vc5_mux_ops = {
.get_rate = vc5_mux_get_rate,
};
static unsigned long vc5_pfd_round_rate(struct clk *hw, unsigned long rate)
{
struct clk *clk_parent = clk_get_parent(hw);
unsigned long parent_rate = clk_get_rate(clk_parent);
unsigned long idiv;
/* PLL cannot operate with input clock above 50 MHz. */
if (rate > 50000000)
return -EINVAL;
/* CLKIN within range of PLL input, feed directly to PLL. */
if (parent_rate <= 50000000)
return parent_rate;
idiv = DIV_ROUND_UP(parent_rate, rate);
if (idiv > 127)
return -EINVAL;
return parent_rate / idiv;
}
static unsigned long vc5_pfd_recalc_rate(struct clk *hw)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_pfd);
unsigned int prediv, div;
struct clk *clk_parent = clk_get_parent(hw);
unsigned long parent_rate = clk_get_rate(clk_parent);
dm_i2c_read(vc5->i2c, VC5_VCO_CTRL_AND_PREDIV, (uchar *)&prediv, 1);
/* The bypass_prediv is set, PLL fed from Ref_in directly. */
if (prediv & VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV)
return parent_rate;
dm_i2c_read(vc5->i2c, VC5_REF_DIVIDER, (uchar *)&div, 1);
/* The Sel_prediv2 is set, PLL fed from prediv2 (Ref_in / 2) */
if (div & VC5_REF_DIVIDER_SEL_PREDIV2)
return parent_rate / 2;
else
return parent_rate / VC5_REF_DIVIDER_REF_DIV(div);
}
static unsigned long vc5_pfd_set_rate(struct clk *hw, unsigned long rate)
{
struct vc5_driver_data *vc5 =
container_of(hw, struct vc5_driver_data, clk_pfd);
unsigned long idiv;
u8 div;
struct clk *clk_parent = clk_get_parent(hw);
unsigned long parent_rate = clk_get_rate(clk_parent);
/* CLKIN within range of PLL input, feed directly to PLL. */
if (parent_rate <= 50000000) {
vc5_update_bits(vc5->i2c, VC5_VCO_CTRL_AND_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV);
vc5_update_bits(vc5->i2c, VC5_REF_DIVIDER, 0xff, 0x00);
return 0;
}
idiv = DIV_ROUND_UP(parent_rate, rate);
/* We have dedicated div-2 predivider. */
if (idiv == 2)
div = VC5_REF_DIVIDER_SEL_PREDIV2;
else
div = VC5_REF_DIVIDER_REF_DIV(idiv);
vc5_update_bits(vc5->i2c, VC5_REF_DIVIDER, 0xff, div);
vc5_update_bits(vc5->i2c, VC5_VCO_CTRL_AND_PREDIV,
VC5_VCO_CTRL_AND_PREDIV_BYPASS_PREDIV, 0);
return 0;
}
static const struct clk_ops vc5_pfd_ops = {
.round_rate = vc5_pfd_round_rate,
.get_rate = vc5_pfd_recalc_rate,
.set_rate = vc5_pfd_set_rate,
};
/*
* VersaClock5 PLL/VCO
*/
static unsigned long vc5_pll_recalc_rate(struct clk *hw)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc = hwdata->vc5;
struct clk *clk_parent = clk_get_parent(hw);
unsigned long parent_rate = clk_get_rate(clk_parent);
u32 div_int, div_frc;
u8 fb[5];
dm_i2c_read(vc->i2c, VC5_FEEDBACK_INT_DIV, fb, 5);
div_int = (fb[0] << 4) | (fb[1] >> 4);
div_frc = (fb[2] << 16) | (fb[3] << 8) | fb[4];
/* The PLL divider has 12 integer bits and 24 fractional bits */
return (parent_rate * div_int) + ((parent_rate * div_frc) >> 24);
}
static unsigned long vc5_pll_round_rate(struct clk *hw, unsigned long rate)
{
struct clk *clk_parent = clk_get_parent(hw);
unsigned long parent_rate = clk_get_rate(clk_parent);
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
u32 div_int;
u64 div_frc;
if (rate < VC5_PLL_VCO_MIN)
rate = VC5_PLL_VCO_MIN;
if (rate > VC5_PLL_VCO_MAX)
rate = VC5_PLL_VCO_MAX;
/* Determine integer part, which is 12 bit wide */
div_int = rate / parent_rate;
if (div_int > 0xfff)
rate = parent_rate * 0xfff;
/* Determine best fractional part, which is 24 bit wide */
div_frc = rate % parent_rate;
div_frc *= BIT(24) - 1;
do_div(div_frc, parent_rate);
hwdata->div_int = div_int;
hwdata->div_frc = (u32)div_frc;
return (parent_rate * div_int) + ((parent_rate * div_frc) >> 24);
}
static unsigned long vc5_pll_set_rate(struct clk *hw, unsigned long rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
u8 fb[5];
fb[0] = hwdata->div_int >> 4;
fb[1] = hwdata->div_int << 4;
fb[2] = hwdata->div_frc >> 16;
fb[3] = hwdata->div_frc >> 8;
fb[4] = hwdata->div_frc;
return dm_i2c_write(vc5->i2c, VC5_FEEDBACK_INT_DIV, fb, 5);
}
static const struct clk_ops vc5_pll_ops = {
.round_rate = vc5_pll_round_rate,
.get_rate = vc5_pll_recalc_rate,
.set_rate = vc5_pll_set_rate,
};
static unsigned long vc5_fod_recalc_rate(struct clk *hw)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc = hwdata->vc5;
struct clk *parent = &vc->clk_pll.hw;
unsigned long parent_rate = vc5_pll_recalc_rate(parent);
/* VCO frequency is divided by two before entering FOD */
u32 f_in = parent_rate / 2;
u32 div_int, div_frc;
u8 od_int[2];
u8 od_frc[4];
dm_i2c_read(vc->i2c, VC5_OUT_DIV_INT(hwdata->num, 0), od_int, 2);
dm_i2c_read(vc->i2c, VC5_OUT_DIV_FRAC(hwdata->num, 0), od_frc, 4);
div_int = (od_int[0] << 4) | (od_int[1] >> 4);
div_frc = (od_frc[0] << 22) | (od_frc[1] << 14) |
(od_frc[2] << 6) | (od_frc[3] >> 2);
/* Avoid division by zero if the output is not configured. */
if (div_int == 0 && div_frc == 0)
return 0;
/* The PLL divider has 12 integer bits and 30 fractional bits */
return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
}
static unsigned long vc5_fod_round_rate(struct clk *hw, unsigned long rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc = hwdata->vc5;
struct clk *parent = &vc->clk_pll.hw;
unsigned long parent_rate = vc5_pll_recalc_rate(parent);
/* VCO frequency is divided by two before entering FOD */
u32 f_in = parent_rate / 2;
u32 div_int;
u64 div_frc;
/* Determine integer part, which is 12 bit wide */
div_int = f_in / rate;
/*
* WARNING: The clock chip does not output signal if the integer part
* of the divider is 0xfff and fractional part is non-zero.
* Clamp the divider at 0xffe to keep the code simple.
*/
if (div_int > 0xffe) {
div_int = 0xffe;
rate = f_in / div_int;
}
/* Determine best fractional part, which is 30 bit wide */
div_frc = f_in % rate;
div_frc <<= 24;
do_div(div_frc, rate);
hwdata->div_int = div_int;
hwdata->div_frc = (u32)div_frc;
return div64_u64((u64)f_in << 24ULL, ((u64)div_int << 24ULL) + div_frc);
}
static unsigned long vc5_fod_set_rate(struct clk *hw, unsigned long rate)
{
struct vc5_hw_data *hwdata = container_of(hw, struct vc5_hw_data, hw);
struct vc5_driver_data *vc5 = hwdata->vc5;
u8 data[14] = {
hwdata->div_frc >> 22, hwdata->div_frc >> 14,
hwdata->div_frc >> 6, hwdata->div_frc << 2,
0, 0, 0, 0, 0,
0, 0,
hwdata->div_int >> 4, hwdata->div_int << 4,
0
};
dm_i2c_write(vc5->i2c, VC5_OUT_DIV_FRAC(hwdata->num, 0), data, 14);
/*
* Toggle magic bit in undocumented register for unknown reason.
* This is what the IDT timing commander tool does and the chip
* datasheet somewhat implies this is needed, but the register
* and the bit is not documented.
*/
vc5_update_bits(vc5->i2c, VC5_GLOBAL_REGISTER,
VC5_GLOBAL_REGISTER_GLOBAL_RESET, 0);
vc5_update_bits(vc5->i2c, VC5_GLOBAL_REGISTER,
VC5_GLOBAL_REGISTER_GLOBAL_RESET,
VC5_GLOBAL_REGISTER_GLOBAL_RESET);
return 0;
}
static const struct clk_ops vc5_fod_ops = {
.round_rate = vc5_fod_round_rate,
.get_rate = vc5_fod_recalc_rate,
.set_rate = vc5_fod_set_rate,
};
static int vc5_clk_out_prepare(struct clk *hw)
{
struct udevice *dev;
struct vc5_driver_data *vc5;
struct vc5_out_data *hwdata;
const u8 mask = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT |
VC5_OUT_DIV_CONTROL_EN_FOD;
unsigned int src;
int ret;
uclass_get_device_by_name(UCLASS_CLK, clk_hw_get_name(hw), &dev);
vc5 = dev_get_priv(dev);
hwdata = &vc5->clk_out[hw->id];
/*
* If the input mux is disabled, enable it first and
* select source from matching FOD.
*/
dm_i2c_read(vc5->i2c, VC5_OUT_DIV_CONTROL(hwdata->num), (uchar *)&src, 1);
if ((src & mask) == 0) {
src = VC5_OUT_DIV_CONTROL_RESET | VC5_OUT_DIV_CONTROL_EN_FOD;
ret = vc5_update_bits(vc5->i2c,
VC5_OUT_DIV_CONTROL(hwdata->num),
mask | VC5_OUT_DIV_CONTROL_RESET, src);
if (ret)
return ret;
}
/* Enable the clock buffer */
vc5_update_bits(vc5->i2c, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF,
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF);
if (hwdata->clk_output_cfg0_mask) {
vc5_update_bits(vc5->i2c, VC5_CLK_OUTPUT_CFG(hwdata->num, 0),
hwdata->clk_output_cfg0_mask,
hwdata->clk_output_cfg0);
}
return 0;
}
static int vc5_clk_out_unprepare(struct clk *hw)
{
struct udevice *dev;
struct vc5_driver_data *vc5;
struct vc5_out_data *hwdata;
int ret;
uclass_get_device_by_name(UCLASS_CLK, clk_hw_get_name(hw), &dev);
vc5 = dev_get_priv(dev);
hwdata = &vc5->clk_out[hw->id];
/* Disable the clock buffer */
ret = vc5_update_bits(vc5->i2c, VC5_CLK_OUTPUT_CFG(hwdata->num, 1),
VC5_CLK_OUTPUT_CFG1_EN_CLKBUF, 0);
return ret;
}
static int vc5_clk_out_set_parent(struct vc5_driver_data *vc, u8 num, u8 index)
{
const u8 mask = VC5_OUT_DIV_CONTROL_RESET |
VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT |
VC5_OUT_DIV_CONTROL_EN_FOD;
const u8 extclk = VC5_OUT_DIV_CONTROL_SELB_NORM |
VC5_OUT_DIV_CONTROL_SEL_EXT;
u8 src = VC5_OUT_DIV_CONTROL_RESET;
if (index == 0)
src |= VC5_OUT_DIV_CONTROL_EN_FOD;
else
src |= extclk;
return vc5_update_bits(vc->i2c, VC5_OUT_DIV_CONTROL(num), mask, src);
}
static unsigned long vc5_clk_out_set_rate(struct clk *hw, unsigned long rate)
{
struct udevice *dev;
struct vc5_driver_data *vc;
struct clk *parent;
uclass_get_device_by_name(UCLASS_CLK, clk_hw_get_name(hw), &dev);
vc = dev_get_priv(dev);
parent = clk_get_parent(&vc->clk_out[hw->id].hw);
/* setting the output rate really means setting the parent FOD rate */
return clk_set_rate(parent, clk_round_rate(parent, rate));
}
static unsigned long vc5_clk_out_get_rate(struct clk *hw)
{
return clk_get_parent_rate(hw);
}
static const struct clk_ops vc5_clk_out_ops = {
.enable = vc5_clk_out_prepare,
.disable = vc5_clk_out_unprepare,
.set_rate = vc5_clk_out_set_rate,
.get_rate = vc5_clk_out_get_rate,
};
static const struct clk_ops vc5_clk_out_sel_ops = {
.enable = vc5_clk_out_prepare,
.disable = vc5_clk_out_unprepare,
.get_rate = vc5_clk_out_get_rate,
};
static const struct clk_ops vc5_clk_ops = {
.enable = vc5_clk_out_prepare,
.disable = vc5_clk_out_unprepare,
.set_rate = vc5_clk_out_set_rate,
.get_rate = vc5_clk_out_get_rate,
};
static int vc5_map_index_to_output(const enum vc5_model model,
const unsigned int n)
{
switch (model) {
case IDT_VC5_5P49V5933:
return (n == 0) ? 0 : 3;
case IDT_VC5_5P49V5923:
case IDT_VC5_5P49V5925:
case IDT_VC5_5P49V5935:
case IDT_VC6_5P49V6901:
case IDT_VC6_5P49V6965:
default:
return n;
}
}
static int vc5_update_mode(ofnode np_output,
struct vc5_out_data *clk_out)
{
u32 value;
if (!ofnode_read_u32(np_output, "idt,mode", &value)) {
clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_CFG_MASK;
switch (value) {
case VC5_CLK_OUTPUT_CFG0_CFG_LVPECL:
case VC5_CLK_OUTPUT_CFG0_CFG_CMOS:
case VC5_CLK_OUTPUT_CFG0_CFG_HCSL33:
case VC5_CLK_OUTPUT_CFG0_CFG_LVDS:
case VC5_CLK_OUTPUT_CFG0_CFG_CMOS2:
case VC5_CLK_OUTPUT_CFG0_CFG_CMOSD:
case VC5_CLK_OUTPUT_CFG0_CFG_HCSL25:
clk_out->clk_output_cfg0 |=
value << VC5_CLK_OUTPUT_CFG0_CFG_SHIFT;
break;
default:
return -EINVAL;
}
}
return 0;
}
static int vc5_update_power(ofnode np_output, struct vc5_out_data *clk_out)
{
u32 value;
if (!ofnode_read_u32(np_output, "idt,voltage-microvolt", &value)) {
clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_PWR_MASK;
switch (value) {
case 1800000:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_18;
break;
case 2500000:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_25;
break;
case 3300000:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_PWR_33;
break;
default:
return -EINVAL;
}
}
return 0;
}
static int vc5_map_cap_value(u32 femtofarads)
{
int mapped_value;
/*
* The datasheet explicitly states 9000 - 25000 with 0.5pF
* steps, but the Programmer's guide shows the steps are 0.430pF.
* After getting feedback from Renesas, the .5pF steps were the
* goal, but 430nF was the actual values.
* Because of this, the actual range goes to 22760 instead of 25000
*/
if (femtofarads < 9000 || femtofarads > 22760)
return -EINVAL;
/*
* The Programmer's guide shows XTAL[5:0] but in reality,
* XTAL[0] and XTAL[1] are both LSB which makes the math
* strange. With clarfication from Renesas, setting the
* values should be simpler by ignoring XTAL[0]
*/
mapped_value = DIV_ROUND_CLOSEST(femtofarads - 9000, 430);
/*
* Since the calculation ignores XTAL[0], there is one
* special case where mapped_value = 32. In reality, this means
* the real mapped value should be 111111b. In other cases,
* the mapped_value needs to be shifted 1 to the left.
*/
if (mapped_value > 31)
mapped_value = 0x3f;
else
mapped_value <<= 1;
return mapped_value;
}
static int vc5_update_cap_load(ofnode node, struct vc5_driver_data *vc5)
{
u32 value;
int mapped_value;
if (!ofnode_read_u32(node, "idt,xtal-load-femtofarads", &value)) {
mapped_value = vc5_map_cap_value(value);
if (mapped_value < 0)
return mapped_value;
/*
* The mapped_value is really the high 6 bits of
* VC5_XTAL_X1_LOAD_CAP and VC5_XTAL_X2_LOAD_CAP, so
* shift the value 2 places.
*/
vc5_update_bits(vc5->i2c, VC5_XTAL_X1_LOAD_CAP, ~0x03, mapped_value << 2);
vc5_update_bits(vc5->i2c, VC5_XTAL_X2_LOAD_CAP, ~0x03, mapped_value << 2);
}
return 0;
}
static int vc5_update_slew(ofnode np_output, struct vc5_out_data *clk_out)
{
u32 value;
if (!ofnode_read_u32(np_output, "idt,slew-percent", &value)) {
clk_out->clk_output_cfg0_mask |= VC5_CLK_OUTPUT_CFG0_SLEW_MASK;
switch (value) {
case 80:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_80;
break;
case 85:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_85;
break;
case 90:
clk_out->clk_output_cfg0 |= VC5_CLK_OUTPUT_CFG0_SLEW_90;
break;
case 100:
clk_out->clk_output_cfg0 |=
VC5_CLK_OUTPUT_CFG0_SLEW_100;
break;
default:
return -EINVAL;
}
}
return 0;
}
static int vc5_get_output_config(struct udevice *dev,
struct vc5_out_data *clk_out)
{
ofnode np_output;
char child_name[5];
int ret = 0;
sprintf(child_name, "OUT%d", clk_out->num + 1);
np_output = dev_read_subnode(dev, child_name);
if (!ofnode_valid(np_output)) {
dev_dbg(dev, "Invalid clock output configuration OUT%d\n",
clk_out->num + 1);
return 0;
}
ret = vc5_update_mode(np_output, clk_out);
if (ret)
return ret;
ret = vc5_update_power(np_output, clk_out);
if (ret)
return ret;
ret = vc5_update_slew(np_output, clk_out);
return ret;
}
static char *versaclock_get_name(const char *dev_name, const char *clk_name, int index)
{
int length;
char *buf;
if (index < 0)
length = snprintf(NULL, 0, "%s.%s", dev_name, clk_name) + 1;
else
length = snprintf(NULL, 0, "%s.%s%d", dev_name, clk_name, index) + 1;
buf = malloc(length);
if (!buf)
ERR_PTR(-ENOMEM);
if (index < 0)
snprintf(buf, length, "%s.%s", dev_name, clk_name);
else
snprintf(buf, length, "%s.%s%d", dev_name, clk_name, index);
return buf;
}
int versaclock_probe(struct udevice *dev)
{
struct vc5_driver_data *vc5 = dev_get_priv(dev);
struct vc5_chip_info *chip = (void *)dev_get_driver_data(dev);
unsigned int n, idx = 0;
char *mux_name, *pfd_name, *pll_name, *outsel_name;
char *out_name[VC5_MAX_CLK_OUT_NUM];
char *fod_name[VC5_MAX_FOD_NUM];
int ret;
u64 val;
val = (u64)dev_read_addr_ptr(dev);
ret = i2c_get_chip(dev->parent, val, 1, &vc5->i2c);
if (ret) {
dev_dbg(dev, "I2C probe failed.\n");
return ret;
}
vc5->chip_info = chip;
vc5->pin_xin = devm_clk_get(dev, "xin");
if (IS_ERR(vc5->pin_xin))
dev_dbg(dev, "failed to get xin clock\n");
ret = clk_enable(vc5->pin_xin);
if (ret)
dev_dbg(dev, "failed to enable XIN clock\n");
vc5->pin_clkin = devm_clk_get(dev, "clkin");
/* Register clock input mux */
if (!IS_ERR(vc5->pin_xin)) {
vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
} else if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL) {
if (IS_ERR(vc5->pin_xin))
return PTR_ERR(vc5->pin_xin);
vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
}
mux_name = versaclock_get_name(dev->name, "mux", -1);
if (IS_ERR(mux_name))
return PTR_ERR(mux_name);
clk_register(&vc5->clk_mux, "versaclock-mux", mux_name, vc5->pin_xin->dev->name);
if (!IS_ERR(vc5->pin_xin))
vc5_mux_set_parent(&vc5->clk_mux, 1);
else
vc5_mux_set_parent(&vc5->clk_mux, 0);
/* Configure Optional Loading Capacitance for external XTAL */
if (!(vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL)) {
ret = vc5_update_cap_load(dev_ofnode(dev), vc5);
if (ret)
dev_dbg(dev, "failed to vc5_update_cap_load\n");
}
/* Register PFD */
pfd_name = versaclock_get_name(dev->name, "pfd", -1);
if (IS_ERR(pfd_name)) {
ret = PTR_ERR(pfd_name);
goto free_mux;
}
ret = clk_register(&vc5->clk_pfd, "versaclock-pfd", pfd_name, vc5->clk_mux.dev->name);
if (ret)
goto free_pfd;
/* Register PLL */
vc5->clk_pll.num = 0;
vc5->clk_pll.vc5 = vc5;
pll_name = versaclock_get_name(dev->name, "pll", -1);
if (IS_ERR(pll_name)) {
ret = PTR_ERR(pll_name);
goto free_pfd;
}
ret = clk_register(&vc5->clk_pll.hw, "versaclock-pll", pll_name, vc5->clk_pfd.dev->name);
if (ret)
goto free_pll;
/* Register FODs */
for (n = 0; n < vc5->chip_info->clk_fod_cnt; n++) {
fod_name[n] = versaclock_get_name(dev->name, "fod", n);
if (IS_ERR(pll_name)) {
ret = PTR_ERR(fod_name[n]);
goto free_fod;
}
idx = vc5_map_index_to_output(vc5->chip_info->model, n);
vc5->clk_fod[n].num = idx;
vc5->clk_fod[n].vc5 = vc5;
ret = clk_register(&vc5->clk_fod[n].hw, "versaclock-fod", fod_name[n],
vc5->clk_pll.hw.dev->name);
if (ret)
goto free_fod;
}
/* Register MUX-connected OUT0_I2C_SELB output */
vc5->clk_out[0].num = idx;
vc5->clk_out[0].vc5 = vc5;
outsel_name = versaclock_get_name(dev->name, "out0_sel_i2cb", -1);
if (IS_ERR(outsel_name)) {
ret = PTR_ERR(outsel_name);
goto free_fod;
};
ret = clk_register(&vc5->clk_out[0].hw, "versaclock-outsel", outsel_name,
vc5->clk_mux.dev->name);
if (ret)
goto free_selb;
/* Register FOD-connected OUTx outputs */
for (n = 1; n < vc5->chip_info->clk_out_cnt; n++) {
idx = vc5_map_index_to_output(vc5->chip_info->model, n - 1);
out_name[n] = versaclock_get_name(dev->name, "out", n);
if (IS_ERR(out_name[n])) {
ret = PTR_ERR(out_name[n]);
goto free_selb;
}
vc5->clk_out[n].num = idx;
vc5->clk_out[n].vc5 = vc5;
ret = clk_register(&vc5->clk_out[n].hw, "versaclock-out", out_name[n],
vc5->clk_fod[idx].hw.dev->name);
if (ret)
goto free_out;
vc5_clk_out_set_parent(vc5, idx, 0);
/* Fetch Clock Output configuration from DT (if specified) */
ret = vc5_get_output_config(dev, &vc5->clk_out[n]);
if (ret) {
dev_dbg(dev, "failed to vc5_get_output_config()\n");
goto free_out;
}
}
return 0;
free_out:
for (n = 1; n < vc5->chip_info->clk_out_cnt; n++) {
clk_free(&vc5->clk_out[n].hw);
free(out_name[n]);
}
free_selb:
clk_free(&vc5->clk_out[0].hw);
free(outsel_name);
free_fod:
for (n = 0; n < vc5->chip_info->clk_fod_cnt; n++) {
clk_free(&vc5->clk_fod[n].hw);
free(fod_name[n]);
}
free_pll:
clk_free(&vc5->clk_pll.hw);
free(pll_name);
free_pfd:
clk_free(&vc5->clk_pfd);
free(pfd_name);
free_mux:
clk_free(&vc5->clk_mux);
free(mux_name);
return ret;
}
static const struct udevice_id versaclock_ids[] = {
{ .compatible = "idt,5p49v5923", .data = (ulong)&idt_5p49v5923_info },
{ .compatible = "idt,5p49v5925", .data = (ulong)&idt_5p49v5925_info },
{ .compatible = "idt,5p49v5933", .data = (ulong)&idt_5p49v5933_info },
{ .compatible = "idt,5p49v5935", .data = (ulong)&idt_5p49v5935_info },
{ .compatible = "idt,5p49v6901", .data = (ulong)&idt_5p49v6901_info },
{ .compatible = "idt,5p49v6965", .data = (ulong)&idt_5p49v6965_info },
{},
};
U_BOOT_DRIVER(versaclock) = {
.name = "versaclock",
.id = UCLASS_CLK,
.ops = &vc5_clk_ops,
.of_match = versaclock_ids,
.probe = versaclock_probe,
.priv_auto = sizeof(struct vc5_driver_data),
};
U_BOOT_DRIVER(versaclock_mux) = {
.name = "versaclock-mux",
.id = UCLASS_CLK,
.ops = &vc5_mux_ops,
};
U_BOOT_DRIVER(versaclock_pfd) = {
.name = "versaclock-pfd",
.id = UCLASS_CLK,
.ops = &vc5_pfd_ops,
};
U_BOOT_DRIVER(versaclock_pll) = {
.name = "versaclock-pll",
.id = UCLASS_CLK,
.ops = &vc5_pll_ops,
};
U_BOOT_DRIVER(versaclock_fod) = {
.name = "versaclock-fod",
.id = UCLASS_CLK,
.ops = &vc5_fod_ops,
};
U_BOOT_DRIVER(versaclock_out) = {
.name = "versaclock-out",
.id = UCLASS_CLK,
.ops = &vc5_clk_out_ops,
};
U_BOOT_DRIVER(versaclock_outsel) = {
.name = "versaclock-outsel",
.id = UCLASS_CLK,
.ops = &vc5_clk_out_sel_ops,
};