blob: acbd43419f2e4a917b0caaf35ad82a2324765ac6 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
* Copyright 2020-2021 NXP
*/
/*
* P2041 RDB board configuration file
* Also supports P2040 RDB
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_TEXT_BASE
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000)
#define CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif
/* High Level Configuration Options */
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
#ifndef __ASSEMBLY__
#include <linux/stringify.h>
#endif
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CFG_SYS_INIT_L2CSR0 L2CSR0_L2E
#define CONFIG_POST CFG_SYS_POST_MEMORY /* test POST memory test */
/*
* Config the L3 Cache as L3 SRAM
*/
#define CFG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
CONFIG_RAMBOOT_TEXT_BASE)
#else
#define CFG_SYS_INIT_L3_ADDR_PHYS CFG_SYS_INIT_L3_ADDR
#endif
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_DCSRBAR 0xf0000000
#define CFG_SYS_DCSRBAR_PHYS 0xf00000000ull
#endif
/*
* DDR Setup
*/
#define CONFIG_VERY_BIG_RAM
#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
#define SPD_EEPROM_ADDRESS 0x52
#define CFG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
/*
* Local Bus Definitions
*/
/* Set the local bus clock 1/8 of platform clock */
#define CFG_SYS_LBC_LCRR LCRR_CLKDIV_8
/*
* This board doesn't have a promjet connector.
* However, it uses commone corenet board LAW and TLB.
* It is necessary to use the same start address with proper offset.
*/
#define CFG_SYS_FLASH_BASE 0xe0000000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_FLASH_BASE_PHYS 0xfe0000000ull
#else
#define CFG_SYS_FLASH_BASE_PHYS CFG_SYS_FLASH_BASE
#endif
#define CONFIG_FSL_CPLD
#define CPLD_BASE 0xffdf0000 /* CPLD registers */
#ifdef CONFIG_PHYS_64BIT
#define CPLD_BASE_PHYS 0xfffdf0000ull
#else
#define CPLD_BASE_PHYS CPLD_BASE
#endif
#define PIXIS_LBMAP_SWITCH 7
#define PIXIS_LBMAP_MASK 0xf0
#define PIXIS_LBMAP_SHIFT 4
#define PIXIS_LBMAP_ALTBANK 0x40
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
/* Nand Flash */
#ifdef CONFIG_NAND_FSL_ELBC
#define CFG_SYS_NAND_BASE 0xffa00000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_NAND_BASE_PHYS 0xfffa00000ull
#else
#define CFG_SYS_NAND_BASE_PHYS CFG_SYS_NAND_BASE
#endif
#define CFG_SYS_NAND_BASE_LIST {CFG_SYS_NAND_BASE}
/* NAND flash config */
#define CFG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
| BR_PS_8 /* Port Size = 8 bit */ \
| BR_MS_FCM /* MSEL = FCM */ \
| BR_V) /* valid */
#define CFG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \
| OR_FCM_PGS /* Large Page*/ \
| OR_FCM_CSCT \
| OR_FCM_CST \
| OR_FCM_CHT \
| OR_FCM_SCY_1 \
| OR_FCM_TRLX \
| OR_FCM_EHTR)
#endif /* CONFIG_NAND_FSL_ELBC */
#define CFG_SYS_FLASH_BANKS_LIST {CFG_SYS_FLASH_BASE_PHYS + 0x8000000}
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CFG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR
/* The assembler doesn't like typecast */
#define CFG_SYS_INIT_RAM_ADDR_PHYS \
((CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
CFG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#else
#define CFG_SYS_INIT_RAM_ADDR_PHYS CFG_SYS_INIT_RAM_ADDR
#define CFG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CFG_SYS_INIT_RAM_ADDR_PHYS_LOW CFG_SYS_INIT_RAM_ADDR_PHYS
#endif
#define CFG_SYS_INIT_RAM_SIZE 0x00004000
#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2)
#define CFG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CFG_SYS_NS16550_COM1 (CFG_SYS_CCSRBAR+0x11C500)
#define CFG_SYS_NS16550_COM2 (CFG_SYS_CCSRBAR+0x11C600)
#define CFG_SYS_NS16550_COM3 (CFG_SYS_CCSRBAR+0x11D500)
#define CFG_SYS_NS16550_COM4 (CFG_SYS_CCSRBAR+0x11D600)
/* I2C */
/*
* RapidIO
*/
#define CFG_SYS_SRIO1_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#else
#define CFG_SYS_SRIO1_MEM_PHYS 0xa0000000
#endif
#define CFG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_SYS_SRIO2_MEM_VIRT 0xb0000000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
#else
#define CFG_SYS_SRIO2_MEM_PHYS 0xb0000000
#endif
#define CFG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */
/*
* for slave u-boot IMAGE instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CFG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
#define CFG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
* for slave UCODE and ENV instored in master memory space,
* PHYS must be aligned based on the SIZE
*/
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CFG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
/* slave core release by master*/
#define CFG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CFG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
/*
* SRIO_PCIE_BOOT - SLAVE
*/
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
(0x300000000ull | CFG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif
/*
* eSPI - Enhanced SPI
*/
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CFG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#define CFG_SYS_PCIE1_IO_VIRT 0xf8000000
#define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000
#define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#define CFG_SYS_PCIE2_IO_VIRT 0xf8010000
#define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CFG_SYS_PCIE3_MEM_VIRT 0xc0000000
#define CFG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
/* Qman/Bman */
#define CFG_SYS_BMAN_NUM_PORTALS 10
#define CFG_SYS_BMAN_MEM_BASE 0xf4000000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_BMAN_MEM_PHYS 0xff4000000ull
#else
#define CFG_SYS_BMAN_MEM_PHYS CFG_SYS_BMAN_MEM_BASE
#endif
#define CFG_SYS_BMAN_MEM_SIZE 0x00200000
#define CFG_SYS_BMAN_SP_CENA_SIZE 0x4000
#define CFG_SYS_BMAN_SP_CINH_SIZE 0x1000
#define CFG_SYS_BMAN_CENA_BASE CFG_SYS_BMAN_MEM_BASE
#define CFG_SYS_BMAN_CENA_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
#define CFG_SYS_BMAN_CINH_BASE (CFG_SYS_BMAN_MEM_BASE + \
CFG_SYS_BMAN_CENA_SIZE)
#define CFG_SYS_BMAN_CINH_SIZE (CFG_SYS_BMAN_MEM_SIZE >> 1)
#define CFG_SYS_BMAN_SWP_ISDR_REG 0xE08
#define CFG_SYS_QMAN_NUM_PORTALS 10
#define CFG_SYS_QMAN_MEM_BASE 0xf4200000
#ifdef CONFIG_PHYS_64BIT
#define CFG_SYS_QMAN_MEM_PHYS 0xff4200000ull
#else
#define CFG_SYS_QMAN_MEM_PHYS CFG_SYS_QMAN_MEM_BASE
#endif
#define CFG_SYS_QMAN_MEM_SIZE 0x00200000
#define CFG_SYS_QMAN_SP_CINH_SIZE 0x1000
#define CFG_SYS_QMAN_CENA_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
#define CFG_SYS_QMAN_CINH_BASE (CFG_SYS_QMAN_MEM_BASE + \
CFG_SYS_QMAN_CENA_SIZE)
#define CFG_SYS_QMAN_CINH_SIZE (CFG_SYS_QMAN_MEM_SIZE >> 1)
#define CFG_SYS_QMAN_SWP_ISDR_REG 0xE08
#ifdef CONFIG_FMAN_ENET
#define CFG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
#define CFG_SYS_FM1_DTSEC2_PHY_ADDR 0x3
#define CFG_SYS_FM1_DTSEC3_PHY_ADDR 0x4
#define CFG_SYS_FM1_DTSEC4_PHY_ADDR 0x1
#define CFG_SYS_FM1_DTSEC5_PHY_ADDR 0x0
#define CFG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c
#define CFG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d
#define CFG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e
#define CFG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f
#define CFG_SYS_FM1_10GEC1_PHY_ADDR 0
#define CFG_SYS_TBIPA_VALUE 8
#endif
#ifdef CONFIG_MMC
#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
#endif
/*
* Miscellaneous configurable options
*/
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
/*
* Environment Configuration
*/
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_UBOOTPATH u-boot.bin
#define __USB_PHY_TYPE utmi
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
"bank_intlv=cs0_cs1\0" \
"netdev=eth0\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \
"tftpflash=tftpboot $loadaddr $uboot && " \
"protect off $ubootaddr +$filesize && " \
"erase $ubootaddr +$filesize && " \
"cp.b $loadaddr $ubootaddr $filesize && " \
"protect on $ubootaddr +$filesize && " \
"cmp.b $loadaddr $ubootaddr $filesize\0" \
"consoledev=ttyS0\0" \
"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
"usb_dr_mode=host\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=p2041rdb/ramdisk.uboot\0" \
"fdtaddr=1e00000\0" \
"fdtfile=p2041rdb/p2041rdb.dtb\0" \
"bdev=sda3\0"
#include <asm/fsl_secure_boot.h>
#endif /* __CONFIG_H */