blob: 98455060396a6105d0df5b1ff6a1319e3aee31a3 [file] [log] [blame]
/*
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
*
* Based on davinci_dvevm.h. Original Copyrights follow:
*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Board
*/
#define CONFIG_DRIVER_TI_EMAC
/* check if direct NOR boot config is used */
#ifndef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_USE_SPIFLASH
#endif
/*
* SoC Configuration
*/
#define CONFIG_MACH_DAVINCI_DA850_EVM
#define CONFIG_ARM926EJS /* arm926ejs CPU core */
#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */
#define CONFIG_SOC_DA850 /* TI DA850 SoC */
#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_DA850_PLL_INIT
#define CONFIG_SYS_DA850_DDR_INIT
#ifdef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_DA8XX_GPIO
#define CONFIG_SYS_TEXT_BASE 0x60000000
#define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11)
#define CONFIG_DA850_LOWLEVEL
#else
#define CONFIG_SYS_TEXT_BASE 0xc1080000
#endif
/*
* Memory Info
*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
/* memtest start addr */
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
/* memtest will be run on 16MB */
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
DAVINCI_SYSCFG_SUSPSRC_UART2 | \
DAVINCI_SYSCFG_SUSPSRC_EMAC | \
DAVINCI_SYSCFG_SUSPSRC_I2C)
/*
* PLL configuration
*/
#define CONFIG_SYS_DV_CLKMODE 0
#define CONFIG_SYS_DA850_PLL0_POSTDIV 1
#define CONFIG_SYS_DA850_PLL0_PLLDIV1 0x8000
#define CONFIG_SYS_DA850_PLL0_PLLDIV2 0x8001
#define CONFIG_SYS_DA850_PLL0_PLLDIV3 0x8002
#define CONFIG_SYS_DA850_PLL0_PLLDIV4 0x8003
#define CONFIG_SYS_DA850_PLL0_PLLDIV5 0x8002
#define CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV1
#define CONFIG_SYS_DA850_PLL0_PLLDIV7 0x8005
#define CONFIG_SYS_DA850_PLL1_POSTDIV 1
#define CONFIG_SYS_DA850_PLL1_PLLDIV1 0x8000
#define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001
#define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8002
#define CONFIG_SYS_DA850_PLL0_PLLM 24
#define CONFIG_SYS_DA850_PLL1_PLLM 21
/*
* DDR2 memory configuration
*/
#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
DV_DDR_PHY_EXT_STRBEN | \
(0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
(1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
(0x3 << DV_DDR_SDCR_CL_SHIFT) | \
(0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \
(0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
(14 << DV_DDR_SDTMR1_RFC_SHIFT) | \
(2 << DV_DDR_SDTMR1_RP_SHIFT) | \
(2 << DV_DDR_SDTMR1_RCD_SHIFT) | \
(1 << DV_DDR_SDTMR1_WR_SHIFT) | \
(5 << DV_DDR_SDTMR1_RAS_SHIFT) | \
(8 << DV_DDR_SDTMR1_RC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
(0 << DV_DDR_SDTMR1_WTR_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
(0 << DV_DDR_SDTMR2_XP_SHIFT) | \
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
(17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
(199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
(0 << DV_DDR_SDTMR2_RTP_SHIFT) | \
(0 << DV_DDR_SDTMR2_CKE_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494
#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
/*
* Serial Driver info
*/
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
#define CONFIG_SPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_WINBOND
#define CONFIG_CMD_SF
#define CONFIG_DAVINCI_SPI
#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#ifdef CONFIG_USE_SPIFLASH
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x30000
#endif
/*
* I2C Configuration
*/
#define CONFIG_HARD_I2C
#define CONFIG_DRIVER_DAVINCI_I2C
#define CONFIG_SYS_I2C_SPEED 25000
#define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20
/*
* Flash & Environment
*/
#ifdef CONFIG_USE_NAND
#undef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_NAND_DAVINCI
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
#define CONFIG_SYS_NAND_MASK_CLE 0x10
#define CONFIG_SYS_NAND_MASK_ALE 0x8
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x28000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000
#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
CONFIG_SYS_NAND_U_BOOT_SIZE - \
CONFIG_SYS_MALLOC_LEN - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { \
24, 25, 26, 27, 28, \
29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
59, 60, 61, 62, 63 }
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_NAND_LOAD
#endif
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
#define CONFIG_MII
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#endif
#ifdef CONFIG_USE_NOR
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3)
#define CONFIG_ENV_SIZE (10 << 10) /* 10KB */
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
#define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */
#define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
+ 3)
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
#endif
#ifdef CONFIG_USE_SPIFLASH
#undef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_ENV_OFFSET (256 << 10)
#define CONFIG_ENV_SECT_SIZE (64 << 10)
#define CONFIG_SYS_NO_FLASH
#endif
/*
* U-Boot general configuration
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_PROMPT "U-Boot > " /* Command Prompt */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
#define CONFIG_VERSION_VARIABLE
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_LONGHELP
#define CONFIG_CRC32_VERIFY
#define CONFIG_MX_CYCLIC
/*
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_HWCONFIG /* enable hwconfig */
#define CONFIG_CMDLINE_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTARGS \
"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp"
#define CONFIG_BOOTDELAY 3
#define CONFIG_EXTRA_ENV_SETTINGS "hwconfig=dsp:wake=yes"
/*
* U-Boot commands
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ENV
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_SAVES
#define CONFIG_CMD_MEMORY
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifndef CONFIG_DRIVER_TI_EMAC
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_DHCP
#undef CONFIG_CMD_MII
#undef CONFIG_CMD_PING
#endif
#ifdef CONFIG_USE_NAND
#undef CONFIG_CMD_FLASH
#undef CONFIG_CMD_IMLS
#define CONFIG_CMD_NAND
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_LZO
#define CONFIG_RBTREE
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#endif
#ifdef CONFIG_USE_SPIFLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_FLASH
#define CONFIG_CMD_SPI
#define CONFIG_CMD_SAVEENV
#endif
#if !defined(CONFIG_USE_NAND) && \
!defined(CONFIG_USE_NOR) && \
!defined(CONFIG_USE_SPIFLASH)
#define CONFIG_ENV_IS_NOWHERE
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ENV_SIZE (16 << 10)
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_ENV
#endif
/* SD/MMC configuration */
#ifndef CONFIG_USE_NOR
#define CONFIG_MMC
#define CONFIG_DAVINCI_MMC_SD1
#define CONFIG_GENERIC_MMC
#define CONFIG_DAVINCI_MMC
#endif
/*
* Enable MMC commands only when
* MMC support is present
*/
#ifdef CONFIG_MMC
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_MMC
#endif
#ifndef CONFIG_DIRECT_NOR_BOOT
/* defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SPL_SPI_BUS 0
#define CONFIG_SPL_SPI_CS 0
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-da850evm.lds"
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_TEXT_BASE 0x80000000
#define CONFIG_SPL_MAX_FOOTPRINT 32768
#endif
/* Load U-Boot Image From MMC */
#ifdef CONFIG_SPL_MMC_LOAD
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x75
#undef CONFIG_SPL_SPI_SUPPORT
#undef CONFIG_SPL_SPI_LOAD
#endif
/* additions for new relocation code, must added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0xc0000000
#ifdef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00
#else
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
GENERATED_GBL_DATA_SIZE)
#endif /* CONFIG_DIRECT_NOR_BOOT */
#endif /* __CONFIG_H */