| /* |
| * Copyright 2013-2015 Arcturus Networks, Inc. |
| * http://www.arcturusnetworks.com/products/ucp1020/ |
| * based on include/configs/p1_p2_rdb_pc.h |
| * original copyright follows: |
| * Copyright 2009-2011 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * QorIQ uCP1020-xx boards configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_FSL_ELBC |
| #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ |
| #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ |
| #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ |
| #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ |
| |
| #if defined(CONFIG_TARTGET_UCP1020T1) |
| |
| #define CONFIG_UCP1020_REV_1_3 |
| |
| #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" |
| #define CONFIG_P1020 |
| |
| #define CONFIG_TSEC_ENET |
| #define CONFIG_TSEC1 |
| #define CONFIG_TSEC3 |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF |
| #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE |
| #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD |
| #define CONFIG_IPADDR 10.80.41.229 |
| #define CONFIG_SERVERIP 10.80.41.227 |
| #define CONFIG_NETMASK 255.255.252.0 |
| #define CONFIG_ETHPRIME "eTSEC3" |
| |
| #ifndef CONFIG_SPI_FLASH |
| #endif |
| #define CONFIG_SYS_REDUNDAND_ENVIRONMENT |
| |
| #define CONFIG_MMC |
| #define CONFIG_SYS_L2_SIZE (256 << 10) |
| |
| #define CONFIG_LAST_STAGE_INIT |
| |
| #endif |
| |
| #if defined(CONFIG_TARGET_UCP1020) |
| |
| #define CONFIG_UCP1020 |
| #define CONFIG_UCP1020_REV_1_3 |
| |
| #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" |
| #define CONFIG_P1020 |
| |
| #define CONFIG_TSEC_ENET |
| #define CONFIG_TSEC1 |
| #define CONFIG_TSEC2 |
| #define CONFIG_TSEC3 |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_HAS_ETH2 |
| #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF |
| #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE |
| #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD |
| #define CONFIG_IPADDR 192.168.1.81 |
| #define CONFIG_IPADDR1 192.168.1.82 |
| #define CONFIG_IPADDR2 192.168.1.83 |
| #define CONFIG_SERVERIP 192.168.1.80 |
| #define CONFIG_GATEWAYIP 102.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| #ifndef CONFIG_SPI_FLASH |
| #endif |
| #define CONFIG_SYS_REDUNDAND_ENVIRONMENT |
| |
| #define CONFIG_MMC |
| #define CONFIG_SYS_L2_SIZE (256 << 10) |
| |
| #define CONFIG_LAST_STAGE_INIT |
| |
| #endif |
| |
| #ifdef CONFIG_SDCARD |
| #define CONFIG_RAMBOOT_SDCARD |
| #define CONFIG_SYS_RAMBOOT |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_SYS_TEXT_BASE 0x11000000 |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc |
| #endif |
| |
| #ifdef CONFIG_SPIFLASH |
| #define CONFIG_RAMBOOT_SPIFLASH |
| #define CONFIG_SYS_RAMBOOT |
| #define CONFIG_SYS_EXTRA_ENV_RELOC |
| #define CONFIG_SYS_TEXT_BASE 0x11000000 |
| #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc |
| #endif |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xeff80000 |
| #endif |
| #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 |
| |
| #ifndef CONFIG_RESET_VECTOR_ADDRESS |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc |
| #endif |
| |
| #ifndef CONFIG_SYS_MONITOR_BASE |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #endif |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE |
| #define CONFIG_E500 |
| /* #define CONFIG_MPC85xx */ |
| |
| #define CONFIG_MP |
| |
| #define CONFIG_FSL_LAW |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_CMD_SATA |
| #define CONFIG_SATA_SIL |
| #define CONFIG_SYS_SATA_MAX_DEVICE 2 |
| #define CONFIG_LIBATA |
| #define CONFIG_LBA48 |
| |
| #define CONFIG_SYS_CLK_FREQ 66666666 |
| #define CONFIG_DDR_CLK_FREQ 66666666 |
| |
| #define CONFIG_HWCONFIG |
| |
| #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ |
| #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ |
| #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ |
| /* |
| * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). |
| * there will be one entry in this array for each two (dummy) sensors in |
| * CONFIG_DTT_SENSORS. |
| * |
| * For uCP1020 module: |
| * - only one ADM1021/NCT72 |
| * - i2c addr 0x41 |
| * - conversion rate 0x02 = 0.25 conversions/second |
| * - ALERT output disabled |
| * - local temp sensor enabled, min set to 0 deg, max set to 85 deg |
| * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg |
| */ |
| #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ |
| 0x02, 0, 1, 0, 85, 1, 0, 85} } |
| |
| #define CONFIG_CMD_DTT |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE |
| #define CONFIG_BTB |
| |
| #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ |
| |
| #define CONFIG_ENABLE_36BIT_PHYS |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x1fffffff |
| #define CONFIG_PANIC_HANG /* do not reset board on panic */ |
| |
| #define CONFIG_SYS_CCSRBAR 0xffe00000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k |
| SPL code*/ |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE |
| #endif |
| |
| /* DDR Setup */ |
| #define CONFIG_DDR_ECC_ENABLE |
| #define CONFIG_SYS_FSL_DDR3 |
| #ifndef CONFIG_DDR_ECC_ENABLE |
| #define CONFIG_SYS_DDR_RAW_TIMING |
| #define CONFIG_DDR_SPD |
| #endif |
| #define CONFIG_SYS_SPD_BUS_NUM 1 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| |
| #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 1 |
| #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| |
| /* Default settings for DDR3 */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 |
| #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 |
| #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f |
| #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 |
| #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 |
| |
| #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 |
| #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 |
| #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 |
| |
| #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 |
| #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 |
| #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 |
| #define CONFIG_SYS_DDR_RCW_1 0x00000000 |
| #define CONFIG_SYS_DDR_RCW_2 0x00000000 |
| #ifdef CONFIG_DDR_ECC_ENABLE |
| #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ |
| #else |
| #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ |
| #endif |
| #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 |
| #define CONFIG_SYS_DDR_TIMING_4 0x00220001 |
| #define CONFIG_SYS_DDR_TIMING_5 0x03402400 |
| |
| #define CONFIG_SYS_DDR_TIMING_3 0x00020000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00330004 |
| #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 |
| #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF |
| #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 |
| #define CONFIG_SYS_DDR_MODE_1 0x40461520 |
| #define CONFIG_SYS_DDR_MODE_2 0x8000c000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* |
| * Memory map |
| * |
| * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable |
| * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) |
| * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 |
| * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable |
| * (early boot only) |
| * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable |
| * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable |
| * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable |
| */ |
| |
| /* |
| * Local Bus Definitions |
| */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ |
| #define CONFIG_SYS_FLASH_BASE 0xec000000 |
| |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| |
| #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ |
| | BR_PS_16 | BR_V) |
| |
| #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| |
| #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ |
| /* Initial L1 address */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS |
| /* Size of used area in RAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ |
| |
| #define CONFIG_SYS_PMC_BASE 0xff980000 |
| #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE |
| #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ |
| BR_PS_8 | BR_V) |
| #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ |
| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ |
| OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ |
| #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ |
| #ifdef CONFIG_NAND_FSL_ELBC |
| #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ |
| #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ |
| #endif |
| |
| /* Serial Port - controlled on board with jumper J8 |
| * open - index 2 |
| * shorted - index 1 |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) |
| #define CONFIG_NS16550_MIN_FUNCTIONS |
| #endif |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } |
| #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ |
| |
| #define CONFIG_RTC_DS1337 |
| #define CONFIG_SYS_RTC_DS1337_NOOSC |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 |
| #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C |
| #define CONFIG_SYS_I2C_IDT6V49205B 0x69 |
| |
| /* |
| * eSPI - Enhanced SPI |
| */ |
| #define CONFIG_HARD_SPI |
| |
| #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 |
| |
| #if defined(CONFIG_PCI) |
| /* |
| * General PCI |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| |
| /* controller 2, direct to uli, tgtid 2, Base address 9000 */ |
| #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* controller 1, Slot 2, tgtid 1, Base address a000 */ |
| #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| |
| #define CONFIG_CMD_PCI |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_DOS_PARTITION |
| #endif /* CONFIG_PCI */ |
| |
| /* |
| * Environment |
| */ |
| #ifdef CONFIG_ENV_FIT_UCBOOT |
| |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) |
| #define CONFIG_ENV_SIZE 0x20000 |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| |
| #else |
| |
| #define CONFIG_ENV_SPI_BUS 0 |
| #define CONFIG_ENV_SPI_CS 0 |
| #define CONFIG_ENV_SPI_MAX_HZ 10000000 |
| #define CONFIG_ENV_SPI_MODE 0 |
| |
| #ifdef CONFIG_RAMBOOT_SPIFLASH |
| |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ |
| #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ |
| #define CONFIG_ENV_SECT_SIZE 0x1000 |
| |
| #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE |
| #endif |
| |
| #elif defined(CONFIG_RAMBOOT_SDCARD) |
| #define CONFIG_ENV_IS_IN_MMC |
| #define CONFIG_FSL_FIXED_MMC_LOCATION |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| |
| #elif defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| |
| #else |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ |
| #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE |
| #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) |
| #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE |
| #endif |
| |
| #endif |
| |
| #endif /* CONFIG_ENV_FIT_UCBOOT */ |
| |
| #define CONFIG_LOADS_ECHO /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_ERRATA |
| #define CONFIG_CMD_CRAMFS |
| |
| /* |
| * USB |
| */ |
| #define CONFIG_HAS_FSL_DR_USB |
| |
| #if defined(CONFIG_HAS_FSL_DR_USB) |
| #define CONFIG_USB_EHCI |
| |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 |
| |
| #ifdef CONFIG_USB_EHCI |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_USB_EHCI_FSL |
| #endif |
| #endif |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #ifdef CONFIG_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR |
| #define CONFIG_MMC_SPI |
| #define CONFIG_CMD_MMC_SPI |
| #define CONFIG_GENERIC_MMC |
| #endif |
| |
| #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA) |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* Misc Extra Settings */ |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #if defined(CONFIG_UCP1020_REV_1_2) |
| #define CONFIG_PHY_MICREL_KSZ9021 |
| #elif defined(CONFIG_UCP1020_REV_1_3) |
| #define CONFIG_PHY_MICREL_KSZ9031 |
| #else |
| #error "UCP1020 module revision is not defined !!!" |
| #endif |
| |
| #define CONFIG_BOOTP_SERVERIP |
| |
| #define CONFIG_MII /* MII PHY management */ |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| |
| #define TSEC1_PHY_ADDR 4 |
| #define TSEC2_PHY_ADDR 0 |
| #define TSEC2_PHY_ADDR_SGMII 0x00 |
| #define TSEC3_PHY_ADDR 6 |
| |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| #endif |
| |
| #define CONFIG_HOSTNAME UCP1020 |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| #define CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #if defined(CONFIG_DONGLE) |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootcmd=run prog_spi_mbrbootcramfs\0" \ |
| "bootfile=uImage\0" \ |
| "consoledev=ttyS0\0" \ |
| "cramfsfile=image.cramfs\0" \ |
| "dtbaddr=0x00c00000\0" \ |
| "dtbfile=image.dtb\0" \ |
| "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| "fileaddr=0x01000000\0" \ |
| "filesize=0x00080000\0" \ |
| "flashmbr=sf probe 0; " \ |
| "tftp $loadaddr $mbr; " \ |
| "sf erase $mbr_offset +$filesize; " \ |
| "sf write $loadaddr $mbr_offset $filesize\0" \ |
| "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ |
| "protect off $nor_recoveryaddr +$filesize; " \ |
| "erase $nor_recoveryaddr +$filesize; " \ |
| "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ |
| "protect on $nor_recoveryaddr +$filesize\0 " \ |
| "flashuboot=tftp $ubootaddr $ubootfile; " \ |
| "protect off $nor_ubootaddr +$filesize; " \ |
| "erase $nor_ubootaddr +$filesize; " \ |
| "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ |
| "protect on $nor_ubootaddr +$filesize\0 " \ |
| "flashworking=tftp $workingaddr $cramfsfile; " \ |
| "protect off $nor_workingaddr +$filesize; " \ |
| "erase $nor_workingaddr +$filesize; " \ |
| "cp.b $workingaddr $nor_workingaddr $filesize; " \ |
| "protect on $nor_workingaddr +$filesize\0 " \ |
| "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| "kerneladdr=0x01100000\0" \ |
| "kernelfile=uImage\0" \ |
| "loadaddr=0x01000000\0" \ |
| "mbr=uCP1020d.mbr\0" \ |
| "mbr_offset=0x00000000\0" \ |
| "mmbr=uCP1020Quiet.mbr\0" \ |
| "mmcpart=0:2\0" \ |
| "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ |
| "mmc erase 1 1; " \ |
| "mmc write $loadaddr 1 1\0" \ |
| "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ |
| "mmc erase 0x40 0x400; " \ |
| "mmc write $loadaddr 0x40 0x400\0" \ |
| "netdev=eth0\0" \ |
| "nor_recoveryaddr=0xEC0A0000\0" \ |
| "nor_ubootaddr=0xEFF80000\0" \ |
| "nor_workingaddr=0xECFA0000\0" \ |
| "norbootrecovery=setenv bootargs $recoverybootargs" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "run norloadrecovery; " \ |
| "bootm $kerneladdr - $dtbaddr\0" \ |
| "norbootworking=setenv bootargs $workingbootargs" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "run norloadworking; " \ |
| "bootm $kerneladdr - $dtbaddr\0" \ |
| "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| "setenv cramfsaddr $nor_recoveryaddr; " \ |
| "cramfsload $dtbaddr $dtbfile; " \ |
| "cramfsload $kerneladdr $kernelfile\0" \ |
| "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| "setenv cramfsaddr $nor_workingaddr; " \ |
| "cramfsload $dtbaddr $dtbfile; " \ |
| "cramfsload $kerneladdr $kernelfile\0" \ |
| "prog_spi_mbr=run spi__mbr\0" \ |
| "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ |
| "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ |
| "run spi__cramfs\0" \ |
| "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "tftp $rootfsaddr $rootfsfile; " \ |
| "tftp $loadaddr $kernelfile; " \ |
| "tftp $dtbaddr $dtbfile; " \ |
| "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| "ramdisk_size=120000\0" \ |
| "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| "recoveryaddr=0x02F00000\0" \ |
| "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ |
| "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| "mw.l 0xffe0f008 0x00400000\0" \ |
| "rootfsaddr=0x02F00000\0" \ |
| "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| "rootpath=/opt/nfsroot\0" \ |
| "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| "protect off 0xeC000000 +$filesize; " \ |
| "erase 0xEC000000 +$filesize; " \ |
| "cp.b $loadaddr 0xEC000000 $filesize; " \ |
| "cmp.b $loadaddr 0xEC000000 $filesize; " \ |
| "protect on 0xeC000000 +$filesize\0" \ |
| "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| "protect off 0xeFF80000 +$filesize; " \ |
| "erase 0xEFF80000 +$filesize; " \ |
| "cp.b $loadaddr 0xEFF80000 $filesize; " \ |
| "cmp.b $loadaddr 0xEFF80000 $filesize; " \ |
| "protect on 0xeFF80000 +$filesize\0" \ |
| "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ |
| "sf probe 0; sf erase 0x8000 +$filesize; " \ |
| "sf write $loadaddr 0x8000 $filesize\0" \ |
| "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ |
| "protect off 0xec0a0000 +$filesize; " \ |
| "erase 0xeC0A0000 +$filesize; " \ |
| "cp.b $loadaddr 0xeC0A0000 $filesize; " \ |
| "protect on 0xec0a0000 +$filesize\0" \ |
| "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ |
| "sf probe 1; sf erase 0 +$filesize; " \ |
| "sf write $loadaddr 0 $filesize\0" \ |
| "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ |
| "sf probe 0; sf erase 0 +$filesize; " \ |
| "sf write $loadaddr 0 $filesize\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=0x01000000\0" \ |
| "ubootfile=u-boot.bin\0" \ |
| "ubootd=u-boot4dongle.bin\0" \ |
| "upgrade=run flashworking\0" \ |
| "usb_phy_type=ulpi\0 " \ |
| "workingaddr=0x02F00000\0" \ |
| "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" |
| |
| #else |
| |
| #if defined(CONFIG_UCP1020T1) |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ |
| "bootfile=uImage\0" \ |
| "consoledev=ttyS0\0" \ |
| "cramfsfile=image.cramfs\0" \ |
| "dtbaddr=0x00c00000\0" \ |
| "dtbfile=image.dtb\0" \ |
| "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| "fileaddr=0x01000000\0" \ |
| "filesize=0x00080000\0" \ |
| "flashmbr=sf probe 0; " \ |
| "tftp $loadaddr $mbr; " \ |
| "sf erase $mbr_offset +$filesize; " \ |
| "sf write $loadaddr $mbr_offset $filesize\0" \ |
| "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ |
| "protect off $nor_recoveryaddr +$filesize; " \ |
| "erase $nor_recoveryaddr +$filesize; " \ |
| "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ |
| "protect on $nor_recoveryaddr +$filesize\0 " \ |
| "flashuboot=tftp $ubootaddr $ubootfile; " \ |
| "protect off $nor_ubootaddr +$filesize; " \ |
| "erase $nor_ubootaddr +$filesize; " \ |
| "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ |
| "protect on $nor_ubootaddr +$filesize\0 " \ |
| "flashworking=tftp $workingaddr $cramfsfile; " \ |
| "protect off $nor_workingaddr +$filesize; " \ |
| "erase $nor_workingaddr +$filesize; " \ |
| "cp.b $workingaddr $nor_workingaddr $filesize; " \ |
| "protect on $nor_workingaddr +$filesize\0 " \ |
| "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| "kerneladdr=0x01100000\0" \ |
| "kernelfile=uImage\0" \ |
| "loadaddr=0x01000000\0" \ |
| "mbr=uCP1020.mbr\0" \ |
| "mbr_offset=0x00000000\0" \ |
| "netdev=eth0\0" \ |
| "nor_recoveryaddr=0xEC0A0000\0" \ |
| "nor_ubootaddr=0xEFF80000\0" \ |
| "nor_workingaddr=0xECFA0000\0" \ |
| "norbootrecovery=setenv bootargs $recoverybootargs" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "run norloadrecovery; " \ |
| "bootm $kerneladdr - $dtbaddr\0" \ |
| "norbootworking=setenv bootargs $workingbootargs" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "run norloadworking; " \ |
| "bootm $kerneladdr - $dtbaddr\0" \ |
| "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| "setenv cramfsaddr $nor_recoveryaddr; " \ |
| "cramfsload $dtbaddr $dtbfile; " \ |
| "cramfsload $kerneladdr $kernelfile\0" \ |
| "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| "setenv cramfsaddr $nor_workingaddr; " \ |
| "cramfsload $dtbaddr $dtbfile; " \ |
| "cramfsload $kerneladdr $kernelfile\0" \ |
| "othbootargs=quiet\0" \ |
| "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "tftp $rootfsaddr $rootfsfile; " \ |
| "tftp $loadaddr $kernelfile; " \ |
| "tftp $dtbaddr $dtbfile; " \ |
| "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| "ramdisk_size=120000\0" \ |
| "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| "recoveryaddr=0x02F00000\0" \ |
| "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ |
| "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| "mw.l 0xffe0f008 0x00400000\0" \ |
| "rootfsaddr=0x02F00000\0" \ |
| "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| "rootpath=/opt/nfsroot\0" \ |
| "silent=1\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootaddr=0x01000000\0" \ |
| "ubootfile=u-boot.bin\0" \ |
| "upgrade=run flashworking\0" \ |
| "workingaddr=0x02F00000\0" \ |
| "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" |
| |
| #else /* For Arcturus Modules */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "bootcmd=run norkernel\0" \ |
| "bootfile=uImage\0" \ |
| "consoledev=ttyS0\0" \ |
| "dtbaddr=0x00c00000\0" \ |
| "dtbfile=image.dtb\0" \ |
| "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ |
| "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ |
| "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ |
| "fileaddr=0x01000000\0" \ |
| "filesize=0x00080000\0" \ |
| "flashmbr=sf probe 0; " \ |
| "tftp $loadaddr $mbr; " \ |
| "sf erase $mbr_offset +$filesize; " \ |
| "sf write $loadaddr $mbr_offset $filesize\0" \ |
| "flashuboot=tftp $loadaddr $ubootfile; " \ |
| "protect off $nor_ubootaddr0 +$filesize; " \ |
| "erase $nor_ubootaddr0 +$filesize; " \ |
| "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ |
| "protect on $nor_ubootaddr0 +$filesize; " \ |
| "protect off $nor_ubootaddr1 +$filesize; " \ |
| "erase $nor_ubootaddr1 +$filesize; " \ |
| "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ |
| "protect on $nor_ubootaddr1 +$filesize\0 " \ |
| "format0=protect off $part0base +$part0size; " \ |
| "erase $part0base +$part0size\0" \ |
| "format1=protect off $part1base +$part1size; " \ |
| "erase $part1base +$part1size\0" \ |
| "format2=protect off $part2base +$part2size; " \ |
| "erase $part2base +$part2size\0" \ |
| "format3=protect off $part3base +$part3size; " \ |
| "erase $part3base +$part3size\0" \ |
| "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ |
| "kerneladdr=0x01100000\0" \ |
| "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ |
| "kernelfile=uImage\0" \ |
| "loadaddr=0x01000000\0" \ |
| "mbr=uCP1020.mbr\0" \ |
| "mbr_offset=0x00000000\0" \ |
| "netdev=eth0\0" \ |
| "nor_ubootaddr0=0xEC000000\0" \ |
| "nor_ubootaddr1=0xEFF80000\0" \ |
| "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ |
| "run norkernelload; " \ |
| "bootm $kerneladdr - $dtbaddr\0" \ |
| "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ |
| "setenv cramfsaddr $part0base; " \ |
| "cramfsload $dtbaddr $dtbfile; " \ |
| "cramfsload $kerneladdr $kernelfile\0" \ |
| "part0base=0xEC100000\0" \ |
| "part0size=0x00700000\0" \ |
| "part1base=0xEC800000\0" \ |
| "part1size=0x02000000\0" \ |
| "part2base=0xEE800000\0" \ |
| "part2size=0x00800000\0" \ |
| "part3base=0xEF000000\0" \ |
| "part3size=0x00F80000\0" \ |
| "partENVbase=0xEC080000\0" \ |
| "partENVsize=0x00080000\0" \ |
| "program0=tftp part0-000000.bin; " \ |
| "protect off $part0base +$filesize; " \ |
| "erase $part0base +$filesize; " \ |
| "cp.b $loadaddr $part0base $filesize; " \ |
| "echo Verifying...; " \ |
| "cmp.b $loadaddr $part0base $filesize\0" \ |
| "program1=tftp part1-000000.bin; " \ |
| "protect off $part1base +$filesize; " \ |
| "erase $part1base +$filesize; " \ |
| "cp.b $loadaddr $part1base $filesize; " \ |
| "echo Verifying...; " \ |
| "cmp.b $loadaddr $part1base $filesize\0" \ |
| "program2=tftp part2-000000.bin; " \ |
| "protect off $part2base +$filesize; " \ |
| "erase $part2base +$filesize; " \ |
| "cp.b $loadaddr $part2base $filesize; " \ |
| "echo Verifying...; " \ |
| "cmp.b $loadaddr $part2base $filesize\0" \ |
| "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ |
| " console=$consoledev,$baudrate $othbootargs; " \ |
| "tftp $rootfsaddr $rootfsfile; " \ |
| "tftp $loadaddr $kernelfile; " \ |
| "tftp $dtbaddr $dtbfile; " \ |
| "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ |
| "ramdisk_size=120000\0" \ |
| "ramdiskfile=rootfs.ext2.gz.uboot\0" \ |
| "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ |
| "mw.l 0xffe0f008 0x00400000\0" \ |
| "rootfsaddr=0x02F00000\0" \ |
| "rootfsfile=rootfs.ext2.gz.uboot\0" \ |
| "rootpath=/opt/nfsroot\0" \ |
| "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ |
| "sf probe 0; sf erase 0 +$filesize; " \ |
| "sf write $loadaddr 0 $filesize\0" \ |
| "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ |
| "protect off 0xeC000000 +$filesize; " \ |
| "erase 0xEC000000 +$filesize; " \ |
| "cp.b $loadaddr 0xEC000000 $filesize; " \ |
| "cmp.b $loadaddr 0xEC000000 $filesize; " \ |
| "protect on 0xeC000000 +$filesize\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ |
| "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "ubootfile=u-boot.bin\0" \ |
| "upgrade=run flashuboot\0" \ |
| "usb_phy_type=ulpi\0 " \ |
| "boot_nfs= " \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr\0" \ |
| "boot_hd = " \ |
| "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "usb start;" \ |
| "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ |
| "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr\0" \ |
| "boot_usb_fat = " \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs " \ |
| "ramdisk_size=$ramdisk_size;" \ |
| "usb start;" \ |
| "fatload usb 0:2 $loadaddr $bootfile;" \ |
| "fatload usb 0:2 $fdtaddr $fdtfile;" \ |
| "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ |
| "boot_usb_ext2 = " \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs " \ |
| "ramdisk_size=$ramdisk_size;" \ |
| "usb start;" \ |
| "ext2load usb 0:4 $loadaddr $bootfile;" \ |
| "ext2load usb 0:4 $fdtaddr $fdtfile;" \ |
| "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ |
| "boot_nor = " \ |
| "setenv bootargs root=/dev/$jffs2nor rw " \ |
| "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ |
| "bootm $norbootaddr - $norfdtaddr\0 " \ |
| "boot_ram = " \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs " \ |
| "ramdisk_size=$ramdisk_size;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr\0" |
| |
| #endif |
| #endif |
| |
| #endif /* __CONFIG_H */ |