blob: 3a022afafd2014d79e74c6b0bf147784e35b4ada [file] [log] [blame]
/*
* Configuation settings for the Freescale MCF54455 EVB board.
*
* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M54455EVB_H
#define _M54455EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MCF5445x /* define processor family */
#define CONFIG_M54455 /* define processor type */
#define CONFIG_M54455EVB /* M54455EVB board */
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#undef CONFIG_WATCHDOG
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Command line configuration */
#include <config_cmd_default.h>
#define CONFIG_CMD_BOOTD
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ELF
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MISC
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#undef CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#undef CONFIG_CMD_LOADB
#undef CONFIG_CMD_LOADS
/* Network configuration */
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
# define CONFIG_NET_MULTI 1
# define CONFIG_MII 1
# define CONFIG_MII_INIT 1
# define CFG_DISCOVER_PHY
# define CFG_RX_ETH_BUFFER 8
# define CFG_FAULT_ECHO_LINK_DOWN
# define CFG_FEC0_PINMUX 0
# define CFG_FEC1_PINMUX 0
# define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
# define CFG_FEC1_MIIBASE CFG_FEC0_IOBASE
# define MCFFEC_TOUT_LOOP 50000
# define CONFIG_HAS_ETH1
# define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
# define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)"
# define CONFIG_ETHADDR 00:e0:0c:bc:e5:60
# define CONFIG_ETH1ADDR 00:e0:0c:bc:e5:61
# define CONFIG_ETHPRIME "FEC0"
# define CONFIG_IPADDR 192.162.1.2
# define CONFIG_NETMASK 255.255.255.0
# define CONFIG_SERVERIP 192.162.1.1
# define CONFIG_GATEWAYIP 192.162.1.1
# define CONFIG_OVERWRITE_ETHADDR_ONCE
/* If CFG_DISCOVER_PHY is not defined - hardcoded */
# ifndef CFG_DISCOVER_PHY
# define FECDUPLEX FULL
# define FECSPEED _100BASET
# else
# ifndef CFG_FAULT_ECHO_LINK_DOWN
# define CFG_FAULT_ECHO_LINK_DOWN
# endif
# endif /* CFG_DISCOVER_PHY */
#endif
#define CONFIG_HOSTNAME M54455EVB
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"inpclk=" MK_STR(CFG_INPUT_CLKSRC) "\0" \
"loadaddr=40010000\0" \
"u-boot=u-boot.bin\0" \
"load=tftp ${loadaddr) ${u-boot}\0" \
"upd=run load; run prog\0" \
"prog=prot off 4000000 402ffff;" \
"era 4000000 402ffff;" \
"cp.b ${loadaddr} 0 ${filesize};" \
"save\0" \
""
/* ATA configuration */
#define CONFIG_ISO_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_IDE_RESET 1
#define CONFIG_IDE_PREINIT 1
#define CONFIG_ATAPI
#undef CONFIG_LBA48
#define CFG_IDE_MAXBUS 1
#define CFG_IDE_MAXDEVICE 2
#define CFG_ATA_BASE_ADDR 0x90000000
#define CFG_ATA_IDE0_OFFSET 0
#define CFG_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */
#define CFG_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */
#define CFG_ATA_STRIDE 4 /* Interval between registers */
#define _IO_BASE 0
/* Realtime clock */
#define CONFIG_MCFRTC
#undef RTC_DEBUG
#define CFG_RTC_OSCILLATOR (32 * CFG_HZ)
/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT
/* I2c */
#define CONFIG_FSL_I2C
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 80000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_OFFSET 0x58000
#define CFG_IMMR CFG_MBAR
/* DSPI and Serial Flash */
#define CONFIG_CF_DSPI
#define CONFIG_SERIAL_FLASH
/* PCI */
#ifdef CONFIG_CMD_PCI
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CFG_PCI_CACHE_LINE_SIZE 4
#define CFG_PCI_MEM_BUS 0xA0000000
#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BUS
#define CFG_PCI_MEM_SIZE 0x10000000
#define CFG_PCI_IO_BUS 0xB1000000
#define CFG_PCI_IO_PHYS CFG_PCI_IO_BUS
#define CFG_PCI_IO_SIZE 0x01000000
#define CFG_PCI_CFG_BUS 0xB0000000
#define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS
#define CFG_PCI_CFG_SIZE 0x01000000
#endif
/* FPGA - Spartan 2 */
/* experiment
#define CONFIG_FPGA CFG_SPARTAN3
#define CONFIG_FPGA_COUNT 1
#define CFG_FPGA_PROG_FEEDBACK
#define CFG_FPGA_CHECK_CTRLC
*/
/* Input, PCI, Flexbus, and VCO */
#define CONFIG_EXTRA_CLOCK
#define CONFIG_PRAM 512 /* 512 KB */
#define CFG_PROMPT "-> "
#define CFG_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x10000)
#define CFG_HZ 1000
#define CFG_MBAR 0xFC000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR 0x80000000
#define CFG_INIT_RAM_END 0x8000 /* End of used area in internal SRAM */
#define CFG_INIT_RAM_CTRL 0x221
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET ((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 16)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x40000000
#define CFG_SDRAM_BASE1 0x48000000
#define CFG_SDRAM_SIZE 256 /* SDRAM size in MB */
#define CFG_SDRAM_CFG1 0x65311610
#define CFG_SDRAM_CFG2 0x59670000
#define CFG_SDRAM_CTRL 0xEA0B2000
#define CFG_SDRAM_EMOD 0x40010000
#define CFG_SDRAM_MODE 0x00010033
#define CFG_MEMTEST_START CFG_SDRAM_BASE + 0x400
#define CFG_MEMTEST_END ((CFG_SDRAM_SIZE - 3) << 20)
#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
#define CFG_BOOTPARAMS_LEN 64*1024
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
/* Initial Memory map for Linux */
#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#define CFG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OVERWRITE 1
#undef CFG_ENV_IS_EMBEDDED
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CFG_ATMEL_BOOT
# define CFG_FLASH_BASE CFG_CS0_BASE
# define CFG_FLASH0_BASE CFG_CS0_BASE
# define CFG_FLASH1_BASE CFG_CS1_BASE
# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000)
# define CFG_ENV_SECT_SIZE 0x2000
#else
# define CFG_FLASH_BASE CFG_CS0_BASE
# define CFG_FLASH0_BASE CFG_CS0_BASE
# define CFG_FLASH1_BASE CFG_CS1_BASE
# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000)
# define CFG_ENV_SECT_SIZE 0x20000
#endif
/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system
keep reset. */
#undef CFG_FLASH_CFI
#ifdef CFG_FLASH_CFI
# define CFG_FLASH_CFI_DRIVER 1
# define CFG_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CFG_FLASH_CFI_WIDTH FLASH_CFI_8BIT
# define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
# define CFG_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CFG_FLASH_CHECKSUM
# define CFG_FLASH_BANKS_LIST { CFG_CS0_BASE, CFG_CS1_BASE }
#else
# define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
# define CFG_ATMEL_REGION 4
# define CFG_ATMEL_TOTALSECT 11
# define CFG_ATMEL_SECT {1, 2, 1, 7}
# define CFG_ATMEL_SECTSZ {0x4000, 0x2000, 0x8000, 0x10000}
# define CFG_INTEL_SECT 137
/* max number of sectors on one chip */
# define CFG_MAX_FLASH_SECT (CFG_ATMEL_TOTALSECT + CFG_INTEL_SECT)
# define CFG_FLASH_ERASE_TOUT 2000 /* Atmel needs longer timeout */
# define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
# define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
# define CFG_FLASH_UNLOCK_TOUT 100 /* Timeout for Flash Clear Lock Bits (in ms) */
# define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CFG_FLASH_CHECKSUM
#ifdef CONFIG_SERIAL_FLASH
# define CFG_FLASH2_BASE 0x01000000
# define CFG_STM_SECT 32
# define CFG_STM_SECTSZ 0x10000
# undef CFG_FLASH_ERASE_TOUT
# define CFG_FLASH_ERASE_TOUT 20000
# define SER_WREN 0x06
# define SER_WRDI 0x04
# define SER_RDID 0x9F
# define SER_RDSR 0x05
# define SER_WRSR 0x01
# define SER_READ 0x03
# define SER_F_READ 0x0B
# define SER_PAGE_PROG 0x02
# define SER_SECT_ERASE 0xD8
# define SER_BULK_ERASE 0xC7
# define SER_DEEP_PWRDN 0xB9
# define SER_RES 0xAB
#endif
#endif
/*
* This is setting for JFFS2 support in u-boot.
* NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
*/
#ifdef CFG_ATMEL_BOOT
# define CONFIG_JFFS2_DEV "nor1"
# define CONFIG_JFFS2_PART_SIZE 0x01000000
# define CONFIG_JFFS2_PART_OFFSET (CFG_FLASH1_BASE + 0x500000)
#else
# define CONFIG_JFFS2_DEV "nor0"
# define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000)
# define CONFIG_JFFS2_PART_OFFSET (CFG_FLASH0_BASE + 0x500000)
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
/*
* CS0 - NOR Flash 1, 2, 4, or 8MB
* CS1 - CompactFlash and registers
* CS2 - CPLD
* CS3 - FPGA
* CS4 - Available
* CS5 - Available
*/
#ifdef CFG_ATMEL_BOOT
/* Atmel Flash */
#define CFG_CS0_BASE 0x04000000
#define CFG_CS0_MASK 0x00070001
#define CFG_CS0_CTRL 0x00001140
/* Intel Flash */
#define CFG_CS1_BASE 0x00000000
#define CFG_CS1_MASK 0x01FF0001
#define CFG_CS1_CTRL 0x00000D60
#define CFG_ATMEL_BASE CFG_CS0_BASE
#else
/* Intel Flash */
#define CFG_CS0_BASE 0x00000000
#define CFG_CS0_MASK 0x01FF0001
#define CFG_CS0_CTRL 0x00000D60
/* Atmel Flash */
#define CFG_CS1_BASE 0x04000000
#define CFG_CS1_MASK 0x00070001
#define CFG_CS1_CTRL 0x00001140
#define CFG_ATMEL_BASE CFG_CS1_BASE
#endif
/* CPLD */
#define CFG_CS2_BASE 0x08000000
#define CFG_CS2_MASK 0x00070001
#define CFG_CS2_CTRL 0x003f1140
/* FPGA */
#define CFG_CS3_BASE 0x09000000
#define CFG_CS3_MASK 0x00070001
#define CFG_CS3_CTRL 0x00000020
#endif /* _M54455EVB_H */