blob: b428fd53121a576fe76471d61caf00ff1c0c1914 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2015 - 2016 Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
#include <common.h>
#include <image.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <asm/spl.h>
#include <asm/arch/hardware.h>
#include <asm/arch/ecc_spl_init.h>
#include <asm/arch/psu_init_gpl.h>
#include <asm/arch/sys_proto.h>
#if defined(CONFIG_DEBUG_UART_BOARD_INIT)
void board_debug_uart_init(void)
{
psu_uboot_init();
}
#endif
void board_init_f(ulong dummy)
{
#if !defined(CONFIG_DEBUG_UART_BOARD_INIT)
psu_uboot_init();
#endif
board_early_init_r();
#ifdef CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT
zynqmp_ecc_init();
#endif
}
static void ps_mode_reset(ulong mode)
{
writel(mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_EN_SHIFT,
&crlapb_base->boot_pin_ctrl);
udelay(5);
writel(mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_VAL_SHIFT |
mode << ZYNQMP_CRL_APB_BOOT_PIN_CTRL_OUT_EN_SHIFT,
&crlapb_base->boot_pin_ctrl);
}
/*
* Set default PS_MODE1 which is used for USB ULPI phy reset
* Also other resets can be connected to this certain pin
*/
#ifndef MODE_RESET
# define MODE_RESET PS_MODE1
#endif
#ifdef CONFIG_SPL_BOARD_INIT
void spl_board_init(void)
{
preloader_console_init();
ps_mode_reset(MODE_RESET);
board_init();
psu_post_config_data();
}
#endif
void board_boot_order(u32 *spl_boot_list)
{
spl_boot_list[0] = spl_boot_device();
if (spl_boot_list[0] == BOOT_DEVICE_MMC1)
spl_boot_list[1] = BOOT_DEVICE_MMC2;
if (spl_boot_list[0] == BOOT_DEVICE_MMC2)
spl_boot_list[1] = BOOT_DEVICE_MMC1;
spl_boot_list[2] = BOOT_DEVICE_RAM;
}
u32 spl_boot_device(void)
{
u32 reg = 0;
u8 bootmode;
#if defined(CONFIG_SPL_ZYNQMP_ALT_BOOTMODE_ENABLED)
/* Change default boot mode at run-time */
writel(CONFIG_SPL_ZYNQMP_ALT_BOOTMODE << BOOT_MODE_ALT_SHIFT,
&crlapb_base->boot_mode);
#endif
reg = readl(&crlapb_base->boot_mode);
if (reg >> BOOT_MODE_ALT_SHIFT)
reg >>= BOOT_MODE_ALT_SHIFT;
bootmode = reg & BOOT_MODES_MASK;
switch (bootmode) {
case JTAG_MODE:
return BOOT_DEVICE_RAM;
#ifdef CONFIG_SPL_MMC
case SD_MODE1:
case SD1_LSHFT_MODE: /* not working on silicon v1 */
return BOOT_DEVICE_MMC2;
case SD_MODE:
case EMMC_MODE:
return BOOT_DEVICE_MMC1;
#endif
#ifdef CONFIG_SPL_DFU
case USB_MODE:
return BOOT_DEVICE_DFU;
#endif
#ifdef CONFIG_SPL_SATA
case SW_SATA_MODE:
return BOOT_DEVICE_SATA;
#endif
#ifdef CONFIG_SPL_SPI
case QSPI_MODE_24BIT:
case QSPI_MODE_32BIT:
return BOOT_DEVICE_SPI;
#endif
default:
printf("Invalid Boot Mode:0x%x\n", bootmode);
break;
}
return 0;
}
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
return 0;
}
#endif