include/configs/MPC8641HPCN.h - platform/external/u-boot - Gitiles

 /*
  * Copyright 2006 Freescale Semiconductor.
  *
  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /*
  * MPC8641HPCN board configuration file
  *
  * Make sure you change the MAC address and other network params first,
  * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* High Level Configuration Options */
 #define CONFIG_MPC86xx		1	/* MPC86xx */
 #define CONFIG_MPC8641		1	/* MPC8641 specific */
 #define CONFIG_MPC8641HPCN	1	/* MPC8641HPCN board specific */
 #define CONFIG_NUM_CPUS         2       /* Number of CPUs in the system */
 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
 #undef DEBUG

 #ifdef RUN_DIAG
 #define CFG_DIAG_ADDR        0xff800000
 #endif

 #define CFG_RESET_ADDRESS    0xfff00100

 #define CONFIG_PCI		1	/* Enable PCI/PCIE */
 #define CONFIG_PCI1		1	/* PCIE controler 1 (ULI bridge) */
 #define CONFIG_PCI2		1	/* PCIE controler 2 (slot) */
 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */

 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #undef CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 #define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 #define CONFIG_NUM_DDR_CONTROLLERS     2
 /* #define CONFIG_DDR_INTERLEAVE               1 */
 #define CACHE_LINE_INTERLEAVING		0x20000000
 #define PAGE_INTERLEAVING		0x21000000
 #define BANK_INTERLEAVING		0x22000000
 #define SUPER_BANK_INTERLEAVING		0x23000000


 #define CONFIG_ALTIVEC          1

 /*
  * L2CR setup -- make sure this is right for your board!
  */
 #define CFG_L2
 #define L2_INIT		0
 #define L2_ENABLE	(L2CR_L2E)

 #ifndef CONFIG_SYS_CLK_FREQ
 #ifndef __ASSEMBLY__
 extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
 #endif

 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */

 #undef	CFG_DRAM_TEST			/* memory test, takes time */
 #define CFG_MEMTEST_START	0x00200000	/* memtest region */
 #define CFG_MEMTEST_END		0x00400000

 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
 #define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default */
 #define CFG_CCSRBAR		0xf8000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */

 #define CFG_PCI1_ADDR		(CFG_CCSRBAR+0x8000)
 #define CFG_PCI2_ADDR		(CFG_CCSRBAR+0x9000)

 /*
  * DDR Setup
  */
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
 #define CONFIG_VERY_BIG_RAM

 #define MPC86xx_DDR_SDRAM_CLK_CNTL

 #if defined(CONFIG_SPD_EEPROM)
     /*
      * Determine DDR configuration from I2C interface.
      */
     #define SPD_EEPROM_ADDRESS1		0x51		/* DDR DIMM */
     #define SPD_EEPROM_ADDRESS2		0x52		/* DDR DIMM */
     #define SPD_EEPROM_ADDRESS3		0x53		/* DDR DIMM */
     #define SPD_EEPROM_ADDRESS4		0x54		/* DDR DIMM */

 #else
     /*
      * Manually set up DDR1 parameters
      */

     #define CFG_SDRAM_SIZE	256		/* DDR is 256MB */

     #define CFG_DDR_CS0_BNDS	0x0000000F
     #define CFG_DDR_CS0_CONFIG	0x80010102      /* Enable, no interleaving */
     #define CFG_DDR_EXT_REFRESH 0x00000000
     #define CFG_DDR_TIMING_0    0x00260802
     #define CFG_DDR_TIMING_1	0x39357322
     #define CFG_DDR_TIMING_2	0x14904cc8
     #define CFG_DDR_MODE_1	0x00480432
     #define CFG_DDR_MODE_2	0x00000000
     #define CFG_DDR_INTERVAL	0x06090100
     #define CFG_DDR_DATA_INIT   0xdeadbeef
     #define CFG_DDR_CLK_CTRL    0x03800000
     #define CFG_DDR_OCD_CTRL    0x00000000
     #define CFG_DDR_OCD_STATUS  0x00000000
     #define CFG_DDR_CONTROL	0xe3008000	/* Type = DDR2 */
     #define CFG_DDR_CONTROL2	0x04400000

     /* Not used in fixed_sdram function */

     #define CFG_DDR_MODE	0x00000022
     #define CFG_DDR_CS1_BNDS	0x00000000
     #define CFG_DDR_CS2_BNDS	0x00000FFF	/* Not done */
     #define CFG_DDR_CS3_BNDS	0x00000FFF	/* Not done */
     #define CFG_DDR_CS4_BNDS	0x00000FFF	/* Not done */
     #define CFG_DDR_CS5_BNDS	0x00000FFF	/* Not done */
 #endif

 #define CFG_ID_EEPROM	1
 #define ID_EEPROM_ADDR 0x57

 /*
  * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
  * There is an 8MB flash.  In effect, the addresses from fe000000 to fe7fffff
  * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
  * However, when u-boot comes up, the flash_init needs hard start addresses
  * to build its info table.  For user convenience, the flash addresses is
  * fe800000 and ff800000.  That way, u-boot knows where the flash is
  * and the user can download u-boot code from promjet to fef00000, a
  * more intuitive location than fe700000.
  *
  * Note that, on switching the boot location, fef00000 becomes fff00000.
  */
 #define CFG_FLASH_BASE          0xfe800000     /* start of FLASH 32M */
 #define CFG_FLASH_BASE2		0xff800000

 #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}

 #define CFG_BR0_PRELIM		0xff001001	/* port size 16bit */
 #define CFG_OR0_PRELIM		0xff006ff7	/* 16MB Boot Flash area*/

 #define CFG_BR1_PRELIM		0xfe001001	/* port size 16bit */
 #define CFG_OR1_PRELIM		0xff006ff7	/* 16MB Alternate Boot Flash area*/

 #define CFG_BR2_PRELIM		0xf8201001	/* port size 16bit */
 #define CFG_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/

 #define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
 #define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/


 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000      /* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
 #define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
 #define PIXIS_RST		0x4	/* PIXIS Reset Control register */
 #define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch register */
 #define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
 #define PIXIS_VCTL		0x10	/* VELA Control Register */
 #define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
 #define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
 #define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */

 #define CFG_MAX_FLASH_BANKS	2		/* number of banks */
 #define CFG_MAX_FLASH_SECT	128		/* sectors per device */

 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 #define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor */

 #define CFG_FLASH_CFI_DRIVER
 #define CFG_FLASH_CFI
 #define CFG_FLASH_EMPTY_INFO

 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 #define CFG_RAMBOOT
 #else
 #undef  CFG_RAMBOOT
 #endif

 #if defined(CFG_RAMBOOT)
 #undef CONFIG_SPD_EEPROM
 #define CFG_SDRAM_SIZE	256
 #endif

 #undef CONFIG_CLOCKS_IN_MHZ

 #define CONFIG_L1_INIT_RAM
 #define CFG_INIT_RAM_LOCK	1
 #ifndef CFG_INIT_RAM_LOCK
 #define CFG_INIT_RAM_ADDR	0x0fd00000	/* Initial RAM address */
 #else
 #define CFG_INIT_RAM_ADDR	0xf8400000	/* Initial RAM address */
 #endif
 #define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */

 #define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 #define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
 #define CFG_MALLOC_LEN	    	(1024 * 1024)    /* Reserved for malloc */

 /* Serial Port */
 #define CONFIG_CONS_INDEX     1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_NS16550
 #define CFG_NS16550_SERIAL
 #define CFG_NS16550_REG_SIZE    1
 #define CFG_NS16550_CLK		get_bus_freq(0)

 #define CFG_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

 #define CFG_NS16550_COM1        (CFG_CCSRBAR+0x4500)
 #define CFG_NS16550_COM2        (CFG_CCSRBAR+0x4600)

 /* Use the HUSH parser */
 #define CFG_HUSH_PARSER
 #ifdef  CFG_HUSH_PARSER
 #define CFG_PROMPT_HUSH_PS2 "> "
 #endif

 /*
  * Pass open firmware flat tree to kernel
  */
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1

 #define OF_CPU		"PowerPC,8641@0"
 #define OF_SOC		"soc8641@f8000000"
 #define OF_TBCLK	(bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH	"/soc8641@f8000000/serial@4500"

 #define CFG_64BIT_VSPRINTF	1
 #define CFG_64BIT_STRTOUL	1

 /*
  * I2C
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 #define CFG_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
 #define CFG_I2C_OFFSET		0x3100

 /*
  * RapidIO MMU
  */
 #define CFG_RIO_MEM_BASE	0xc0000000	/* base address */
 #define CFG_RIO_MEM_PHYS	CFG_RIO_MEM_BASE
 #define CFG_RIO_MEM_SIZE	0x20000000	/* 128M */

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CFG_PCI1_MEM_BASE	0x80000000
 #define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe2000000
 #define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */

 /* PCI view of System Memory */
 #define CFG_PCI_MEMORY_BUS      0x00000000
 #define CFG_PCI_MEMORY_PHYS     0x00000000
 #define CFG_PCI_MEMORY_SIZE     0x80000000

 /* For RTL8139 */
 #define KSEG1ADDR(x)		({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
 #define _IO_BASE                0x00000000

 #define CFG_PCI2_MEM_BASE	0xa0000000
 #define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
 #define CFG_PCI2_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI2_IO_BASE	0x00000000
 #define CFG_PCI2_IO_PHYS	0xe3000000
 #define CFG_PCI2_IO_SIZE	0x00100000	/* 1M */

 #if defined(CONFIG_PCI)

 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */

 #undef CFG_SCSI_SCAN_BUS_REVERSE

 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP	               	/* do pci plug-and-play */

 #define CONFIG_RTL8139

 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP

 /************************************************************
  * USB support
  ************************************************************/
 #define CONFIG_PCI_OHCI		1
 #define CONFIG_USB_OHCI_NEW		1
 #define CONFIG_USB_KEYBOARD	1
 #define CFG_DEVICE_DEREGISTER
 #define CFG_USB_EVENT_POLL	1
 #define CFG_USB_OHCI_SLOT_NAME 	"ohci_pci"
 #define CFG_USB_OHCI_MAX_ROOT_PORTS 15

 #if !defined(CONFIG_PCI_PNP)
     #define PCI_ENET0_IOADDR	0xe0000000
     #define PCI_ENET0_MEMADDR	0xe0000000
     #define PCI_IDSEL_NUMBER	0x0c 	/* slot0->3(IDSEL)=12->15 */
 #endif

 /*PCIE video card used*/
 #define VIDEO_IO_OFFSET		CFG_PCI2_IO_PHYS

 /*PCI video card used*/
 /*#define VIDEO_IO_OFFSET	CFG_PCI1_IO_PHYS*/

 /* video */
 #define CONFIG_VIDEO

 #if defined(CONFIG_VIDEO)
 #define CONFIG_BIOSEMU
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_ATI_RADEON_FB
 #define CONFIG_VIDEO_LOGO
 /*#define CONFIG_CONSOLE_CURSOR*/
 #define CFG_ISA_IO_BASE_ADDRESS CFG_PCI2_IO_PHYS
 #endif

 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */

 #define CONFIG_DOS_PARTITION
 #define CONFIG_SCSI_AHCI

 #ifdef CONFIG_SCSI_AHCI
 #define CONFIG_SATA_ULI5288
 #define CFG_SCSI_MAX_SCSI_ID	4
 #define CFG_SCSI_MAX_LUN	1
 #define CFG_SCSI_MAX_DEVICE 	(CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
 #define CFG_SCSI_MAXDEVICE	CFG_SCSI_MAX_DEVICE
 #endif

 #define CONFIG_MPC86XX_PCI2

 #endif	/* CONFIG_PCI */

 #if defined(CONFIG_TSEC_ENET)

 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI 	1
 #endif

 #define CONFIG_MII		1	/* MII PHY management */

 #define CONFIG_TSEC1    1
 #define CONFIG_TSEC1_NAME       "eTSEC1"
 #define CONFIG_TSEC2    1
 #define CONFIG_TSEC2_NAME       "eTSEC2"
 #define CONFIG_TSEC3    1
 #define CONFIG_TSEC3_NAME       "eTSEC3"
 #define CONFIG_TSEC4    1
 #define CONFIG_TSEC4_NAME       "eTSEC4"

 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC3_PHY_ADDR		2
 #define TSEC4_PHY_ADDR		3
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
 #define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)

 #define CONFIG_ETHPRIME		"eTSEC1"

 #endif	/* CONFIG_TSEC_ENET */

 /*
  * BAT0         2G     Cacheable, non-guarded
  * 0x0000_0000  2G     DDR
  */
 #define CFG_DBAT0L      (BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CFG_DBAT0U      (BATU_BL_2G | BATU_VS | BATU_VP)
 #define CFG_IBAT0L      (BATL_PP_RW | BATL_MEMCOHERENCE )
 #define CFG_IBAT0U      CFG_DBAT0U

 /*
  * BAT1         1G     Cache-inhibited, guarded
  * 0x8000_0000  512M   PCI-Express 1 Memory
  * 0xa000_0000  512M   PCI-Express 2 Memory
  *	Changed it for operating from 0xd0000000
  */
 #define CFG_DBAT1L      ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT1U	(CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
 #define CFG_IBAT1L	(CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT1U      CFG_DBAT1U

 /*
  * BAT2         512M   Cache-inhibited, guarded
  * 0xc000_0000  512M   RapidIO Memory
  */
 #define CFG_DBAT2L      (CFG_RIO_MEM_PHYS | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT2U	(CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
 #define CFG_IBAT2L	(CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT2U      CFG_DBAT2U

 /*
  * BAT3         4M     Cache-inhibited, guarded
  * 0xf800_0000  4M     CCSR
  */
 #define CFG_DBAT3L      ( CFG_CCSRBAR | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT3U      (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
 #define CFG_IBAT3L      (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT3U      CFG_DBAT3U

 /*
  * BAT4         32M    Cache-inhibited, guarded
  * 0xe200_0000  16M    PCI-Express 1 I/O
  * 0xe300_0000  16M    PCI-Express 2 I/0
  *    Note that this is at 0xe0000000
  */
 #define CFG_DBAT4L      ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT4U	(CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
 #define CFG_IBAT4L	(CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CFG_IBAT4U      CFG_DBAT4U

 /*
  * BAT5         128K   Cacheable, non-guarded
  * 0xe401_0000  128K   Init RAM for stack in the CPU DCache (no backing memory)
  */
 #define CFG_DBAT5L      (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CFG_DBAT5U      (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 #define CFG_IBAT5L      CFG_DBAT5L
 #define CFG_IBAT5U      CFG_DBAT5U

 /*
  * BAT6         32M    Cache-inhibited, guarded
  * 0xfe00_0000  32M    FLASH
  */
 #define CFG_DBAT6L      ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
 			| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_DBAT6U      ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
 #define CFG_IBAT6L      ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CFG_IBAT6U      CFG_DBAT6U

 #define CFG_DBAT7L 0x00000000
 #define CFG_DBAT7U 0x00000000
 #define CFG_IBAT7L 0x00000000
 #define CFG_IBAT7U 0x00000000

 /*
  * Environment
  */
 #ifndef CFG_RAMBOOT
     #define CFG_ENV_IS_IN_FLASH	1
     #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x60000)
     #define CFG_ENV_SECT_SIZE		0x10000	/* 64K(one sector) for env */
     #define CFG_ENV_SIZE		0x2000
 #else
     #define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
     #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
     #define CFG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PING
 #define CONFIG_CMD_I2C

 #if defined(CFG_RAMBOOT)
     #undef CONFIG_CMD_ENV
 #endif

 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
     #define CONFIG_CMD_SCSI
     #define CONFIG_CMD_EXT2
 #endif


 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory	*/
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */

 #if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
 #endif

 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args */
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
 #define CFG_HZ		1000		/* decrementer freq: 1ms ticks */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/

 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
 #if defined(CONFIG_CMD_KGDB)
     #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */

 #if defined(CONFIG_CMD_KGDB)
     #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
     #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif

 /*
  * Environment Configuration
  */

 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_ETHADDR   00:E0:0C:00:00:01
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
 #define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif

 #define CONFIG_HAS_ETH0		1
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_HAS_ETH2		1
 #define CONFIG_HAS_ETH3		1

 #define CONFIG_IPADDR		192.168.1.100

 #define CONFIG_HOSTNAME		unknown
 #define CONFIG_ROOTPATH		/opt/nfsroot
 #define CONFIG_BOOTFILE		uImage
 #define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */

 #define CONFIG_SERVERIP		192.168.1.1
 #define CONFIG_GATEWAYIP	192.168.1.1
 #define CONFIG_NETMASK		255.255.255.0

 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000

 #define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */

 #define CONFIG_BAUDRATE	115200

 #define	CONFIG_EXTRA_ENV_SETTINGS				        \
    "netdev=eth0\0"                                                      \
    "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" 				\
    "tftpflash=tftpboot $loadaddr $uboot; " 			\
 	"protect off " MK_STR(TEXT_BASE) " +$filesize; " 	\
 	"erase " MK_STR(TEXT_BASE) " +$filesize; " 		\
 	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " 	\
 	"protect on " MK_STR(TEXT_BASE) " +$filesize; " 	\
 	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" 	\
    "consoledev=ttyS0\0"                                                 \
    "ramdiskaddr=2000000\0"						\
    "ramdiskfile=your.ramdisk.u-boot\0"                                  \
    "dtbaddr=c00000\0"						\
    "dtbfile=mpc8641_hpcn.dtb\0"                                  \
    "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
    "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
    "maxcpus=2"


 #define CONFIG_NFSBOOTCOMMAND	                                        \
    "setenv bootargs root=/dev/nfs rw "                                  \
       "nfsroot=$serverip:$rootpath "                                    \
       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
       "console=$consoledev,$baudrate $othbootargs;"                     \
    "tftp $loadaddr $bootfile;"                                          \
    "tftp $dtbaddr $dtbfile;"                                          \
    "bootm $loadaddr - $dtbaddr"

 #define CONFIG_RAMBOOTCOMMAND \
    "setenv bootargs root=/dev/ram rw "                                  \
       "console=$consoledev,$baudrate $othbootargs;"                     \
    "tftp $ramdiskaddr $ramdiskfile;"                                    \
    "tftp $loadaddr $bootfile;"                                          \
    "tftp $dtbaddr $dtbfile;"                                          \
    "bootm $loadaddr $ramdiskaddr $dtbaddr"

 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2006 Freescale Semiconductor.
	*
	* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/*
	* MPC8641HPCN board configuration file
	*
	* Make sure you change the MAC address and other network params first,
	* search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* High Level Configuration Options */
	#define CONFIG_MPC86xx 1 /* MPC86xx */
	#define CONFIG_MPC8641 1 /* MPC8641 specific */
	#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
	#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
	#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
	#undef DEBUG

	#ifdef RUN_DIAG
	#define CFG_DIAG_ADDR 0xff800000
	#endif

	#define CFG_RESET_ADDRESS 0xfff00100

	#define CONFIG_PCI 1 /* Enable PCI/PCIE */
	#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */
	#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */
	#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */

	#define CONFIG_TSEC_ENET /* tsec ethernet support */
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
	#undef CONFIG_DDR_DLL /* possible DLL fix needed */
	#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
	#define CONFIG_DDR_ECC /* only for ECC DDR module */
	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
	#define CONFIG_NUM_DDR_CONTROLLERS 2
	/* #define CONFIG_DDR_INTERLEAVE 1 */
	#define CACHE_LINE_INTERLEAVING 0x20000000
	#define PAGE_INTERLEAVING 0x21000000
	#define BANK_INTERLEAVING 0x22000000
	#define SUPER_BANK_INTERLEAVING 0x23000000


	#define CONFIG_ALTIVEC 1

	/*
	* L2CR setup -- make sure this is right for your board!
	*/
	#define CFG_L2
	#define L2_INIT 0
	#define L2_ENABLE (L2CR_L2E)

	#ifndef CONFIG_SYS_CLK_FREQ
	#ifndef __ASSEMBLY__
	extern unsigned long get_board_sys_clk(unsigned long dummy);
	#endif
	#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
	#endif

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */

	#undef CFG_DRAM_TEST /* memory test, takes time */
	#define CFG_MEMTEST_START 0x00200000 /* memtest region */
	#define CFG_MEMTEST_END 0x00400000

	/*
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	*/
	#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
	#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
	#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */

	#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
	#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)

	/*
	* DDR Setup
	*/
	#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
	#define CONFIG_VERY_BIG_RAM

	#define MPC86xx_DDR_SDRAM_CLK_CNTL

	#if defined(CONFIG_SPD_EEPROM)
	/*
	* Determine DDR configuration from I2C interface.
	*/
	#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
	#define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
	#define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
	#define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */

	#else
	/*
	* Manually set up DDR1 parameters
	*/

	#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */

	#define CFG_DDR_CS0_BNDS 0x0000000F
	#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
	#define CFG_DDR_EXT_REFRESH 0x00000000
	#define CFG_DDR_TIMING_0 0x00260802
	#define CFG_DDR_TIMING_1 0x39357322
	#define CFG_DDR_TIMING_2 0x14904cc8
	#define CFG_DDR_MODE_1 0x00480432
	#define CFG_DDR_MODE_2 0x00000000
	#define CFG_DDR_INTERVAL 0x06090100
	#define CFG_DDR_DATA_INIT 0xdeadbeef
	#define CFG_DDR_CLK_CTRL 0x03800000
	#define CFG_DDR_OCD_CTRL 0x00000000
	#define CFG_DDR_OCD_STATUS 0x00000000
	#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
	#define CFG_DDR_CONTROL2 0x04400000

	/* Not used in fixed_sdram function */

	#define CFG_DDR_MODE 0x00000022
	#define CFG_DDR_CS1_BNDS 0x00000000
	#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
	#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
	#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
	#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
	#endif

	#define CFG_ID_EEPROM 1
	#define ID_EEPROM_ADDR 0x57

	/*
	* In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
	* There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
	* map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
	* However, when u-boot comes up, the flash_init needs hard start addresses
	* to build its info table. For user convenience, the flash addresses is
	* fe800000 and ff800000. That way, u-boot knows where the flash is
	* and the user can download u-boot code from promjet to fef00000, a
	* more intuitive location than fe700000.
	*
	* Note that, on switching the boot location, fef00000 becomes fff00000.
	*/
	#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
	#define CFG_FLASH_BASE2 0xff800000

	#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}

	#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
	#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/

	#define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */
	#define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/

	#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
	#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/

	#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
	#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/


	#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
	#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
	#define PIXIS_ID 0x0 /* Board ID at offset 0 */
	#define PIXIS_VER 0x1 /* Board version at offset 1 */
	#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
	#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
	#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
	#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
	#define PIXIS_VCTL 0x10 /* VELA Control Register */
	#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
	#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
	#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
	#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
	#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
	#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
	#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */

	#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
	#define CFG_MAX_FLASH_SECT 128 /* sectors per device */

	#undef CFG_FLASH_CHECKSUM
	#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */

	#define CFG_FLASH_CFI_DRIVER
	#define CFG_FLASH_CFI
	#define CFG_FLASH_EMPTY_INFO

	#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
	#define CFG_RAMBOOT
	#else
	#undef CFG_RAMBOOT
	#endif

	#if defined(CFG_RAMBOOT)
	#undef CONFIG_SPD_EEPROM
	#define CFG_SDRAM_SIZE 256
	#endif

	#undef CONFIG_CLOCKS_IN_MHZ

	#define CONFIG_L1_INIT_RAM
	#define CFG_INIT_RAM_LOCK 1
	#ifndef CFG_INIT_RAM_LOCK
	#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
	#else
	#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
	#endif
	#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */

	#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 1
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CFG_NS16550
	#define CFG_NS16550_SERIAL
	#define CFG_NS16550_REG_SIZE 1
	#define CFG_NS16550_CLK get_bus_freq(0)

	#define CFG_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

	#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
	#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)

	/* Use the HUSH parser */
	#define CFG_HUSH_PARSER
	#ifdef CFG_HUSH_PARSER
	#define CFG_PROMPT_HUSH_PS2 "> "
	#endif

	/*
	* Pass open firmware flat tree to kernel
	*/
	#define CONFIG_OF_FLAT_TREE 1
	#define CONFIG_OF_BOARD_SETUP 1

	#define OF_CPU "PowerPC,8641@0"
	#define OF_SOC "soc8641@f8000000"
	#define OF_TBCLK (bd->bi_busfreq / 4)
	#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"

	#define CFG_64BIT_VSPRINTF 1
	#define CFG_64BIT_STRTOUL 1

	/*
	* I2C
	*/
	#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
	#define CONFIG_HARD_I2C /* I2C with hardware support*/
	#undef CONFIG_SOFT_I2C /* I2C bit-banged */
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F
	#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
	#define CFG_I2C_OFFSET 0x3100

	/*
	* RapidIO MMU
	*/
	#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
	#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
	#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CFG_PCI1_MEM_BASE 0x80000000
	#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
	#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
	#define CFG_PCI1_IO_BASE 0x00000000
	#define CFG_PCI1_IO_PHYS 0xe2000000
	#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */

	/* PCI view of System Memory */
	#define CFG_PCI_MEMORY_BUS 0x00000000
	#define CFG_PCI_MEMORY_PHYS 0x00000000
	#define CFG_PCI_MEMORY_SIZE 0x80000000

	/* For RTL8139 */
	#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu((u32 )(x)); (&_x);})
	#define _IO_BASE 0x00000000

	#define CFG_PCI2_MEM_BASE 0xa0000000
	#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
	#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
	#define CFG_PCI2_IO_BASE 0x00000000
	#define CFG_PCI2_IO_PHYS 0xe3000000
	#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */

	#if defined(CONFIG_PCI)

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */

	#undef CFG_SCSI_SCAN_BUS_REVERSE

	#define CONFIG_NET_MULTI
	#define CONFIG_PCI_PNP /* do pci plug-and-play */

	#define CONFIG_RTL8139

	#undef CONFIG_EEPRO100
	#undef CONFIG_TULIP

	/************************************************************
	* USB support
	************************************************************/
	#define CONFIG_PCI_OHCI 1
	#define CONFIG_USB_OHCI_NEW 1
	#define CONFIG_USB_KEYBOARD 1
	#define CFG_DEVICE_DEREGISTER
	#define CFG_USB_EVENT_POLL 1
	#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
	#define CFG_USB_OHCI_MAX_ROOT_PORTS 15

	#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR 0xe0000000
	#define PCI_ENET0_MEMADDR 0xe0000000
	#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
	#endif

	/PCIE video card used/
	#define VIDEO_IO_OFFSET CFG_PCI2_IO_PHYS

	/PCI video card used/
	/#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS/

	/* video */
	#define CONFIG_VIDEO

	#if defined(CONFIG_VIDEO)
	#define CONFIG_BIOSEMU
	#define CONFIG_CFB_CONSOLE
	#define CONFIG_VIDEO_SW_CURSOR
	#define CONFIG_VGA_AS_SINGLE_DEVICE
	#define CONFIG_ATI_RADEON_FB
	#define CONFIG_VIDEO_LOGO
	/#define CONFIG_CONSOLE_CURSOR/
	#define CFG_ISA_IO_BASE_ADDRESS CFG_PCI2_IO_PHYS
	#endif

	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */

	#define CONFIG_DOS_PARTITION
	#define CONFIG_SCSI_AHCI

	#ifdef CONFIG_SCSI_AHCI
	#define CONFIG_SATA_ULI5288
	#define CFG_SCSI_MAX_SCSI_ID 4
	#define CFG_SCSI_MAX_LUN 1
	#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
	#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
	#endif

	#define CONFIG_MPC86XX_PCI2

	#endif /* CONFIG_PCI */

	#if defined(CONFIG_TSEC_ENET)

	#ifndef CONFIG_NET_MULTI
	#define CONFIG_NET_MULTI 1
	#endif

	#define CONFIG_MII 1 /* MII PHY management */

	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "eTSEC1"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "eTSEC2"
	#define CONFIG_TSEC3 1
	#define CONFIG_TSEC3_NAME "eTSEC3"
	#define CONFIG_TSEC4 1
	#define CONFIG_TSEC4_NAME "eTSEC4"

	#define TSEC1_PHY_ADDR 0
	#define TSEC2_PHY_ADDR 1
	#define TSEC3_PHY_ADDR 2
	#define TSEC4_PHY_ADDR 3
	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC3_PHYIDX 0
	#define TSEC4_PHYIDX 0
	#define TSEC1_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC2_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC3_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC4_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)

	#define CONFIG_ETHPRIME "eTSEC1"

	#endif /* CONFIG_TSEC_ENET */

	/*
	* BAT0 2G Cacheable, non-guarded
	* 0x0000_0000 2G DDR
	*/
	#define CFG_DBAT0L (BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CFG_DBAT0U (BATU_BL_2G \| BATU_VS \| BATU_VP)
	#define CFG_IBAT0L (BATL_PP_RW \| BATL_MEMCOHERENCE )
	#define CFG_IBAT0U CFG_DBAT0U

	/*
	* BAT1 1G Cache-inhibited, guarded
	* 0x8000_0000 512M PCI-Express 1 Memory
	* 0xa000_0000 512M PCI-Express 2 Memory
	* Changed it for operating from 0xd0000000
	*/
	#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS \| BATU_BL_1G \| BATU_VS \| BATU_VP)
	#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CFG_IBAT1U CFG_DBAT1U

	/*
	* BAT2 512M Cache-inhibited, guarded
	* 0xc000_0000 512M RapidIO Memory
	*/
	#define CFG_DBAT2L (CFG_RIO_MEM_PHYS \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT2U (CFG_RIO_MEM_PHYS \| BATU_BL_512M \| BATU_VS \| BATU_VP)
	#define CFG_IBAT2L (CFG_RIO_MEM_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CFG_IBAT2U CFG_DBAT2U

	/*
	* BAT3 4M Cache-inhibited, guarded
	* 0xf800_0000 4M CCSR
	*/
	#define CFG_DBAT3L ( CFG_CCSRBAR \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT3U (CFG_CCSRBAR \| BATU_BL_4M \| BATU_VS \| BATU_VP)
	#define CFG_IBAT3L (CFG_CCSRBAR \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CFG_IBAT3U CFG_DBAT3U

	/*
	* BAT4 32M Cache-inhibited, guarded
	* 0xe200_0000 16M PCI-Express 1 I/O
	* 0xe300_0000 16M PCI-Express 2 I/0
	* Note that this is at 0xe0000000
	*/
	#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT4U (CFG_PCI1_IO_PHYS \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	#define CFG_IBAT4L (CFG_PCI1_IO_PHYS \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CFG_IBAT4U CFG_DBAT4U

	/*
	* BAT5 128K Cacheable, non-guarded
	* 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
	*/
	#define CFG_DBAT5L (CFG_INIT_RAM_ADDR \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CFG_DBAT5U (CFG_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)
	#define CFG_IBAT5L CFG_DBAT5L
	#define CFG_IBAT5U CFG_DBAT5U

	/*
	* BAT6 32M Cache-inhibited, guarded
	* 0xfe00_0000 32M FLASH
	*/
	#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) \| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) \| BATU_BL_32M \| BATU_VS \| BATU_VP)
	#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CFG_IBAT6U CFG_DBAT6U

	#define CFG_DBAT7L 0x00000000
	#define CFG_DBAT7U 0x00000000
	#define CFG_IBAT7L 0x00000000
	#define CFG_IBAT7U 0x00000000

	/*
	* Environment
	*/
	#ifndef CFG_RAMBOOT
	#define CFG_ENV_IS_IN_FLASH 1
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000)
	#define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
	#define CFG_ENV_SIZE 0x2000
	#else
	#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
	#define CFG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PING
	#define CONFIG_CMD_I2C

	#if defined(CFG_RAMBOOT)
	#undef CONFIG_CMD_ENV
	#endif

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_SCSI
	#define CONFIG_CMD_EXT2
	#endif


	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_LOAD_ADDR 0x2000000 /* default load address */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */

	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif

	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
	#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/

	/* Cache Configuration */
	#define CFG_DCACHE_SIZE 32768
	#define CFG_CACHELINE_SIZE 32
	#if defined(CONFIG_CMD_KGDB)
	#define CFG_CACHELINE_SHIFT 5 /log base 2 of the above value/
	#endif

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif

	/*
	* Environment Configuration
	*/

	/* The mac addresses for all ethernet interface */
	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_ETHADDR 00:E0:0C:00:00:01
	#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
	#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
	#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
	#endif

	#define CONFIG_HAS_ETH0 1
	#define CONFIG_HAS_ETH1 1
	#define CONFIG_HAS_ETH2 1
	#define CONFIG_HAS_ETH3 1

	#define CONFIG_IPADDR 192.168.1.100

	#define CONFIG_HOSTNAME unknown
	#define CONFIG_ROOTPATH /opt/nfsroot
	#define CONFIG_BOOTFILE uImage
	#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */

	#define CONFIG_SERVERIP 192.168.1.1
	#define CONFIG_GATEWAYIP 192.168.1.1
	#define CONFIG_NETMASK 255.255.255.0

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 1000000

	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off " MK_STR(TEXT_BASE) " +$filesize; " \
	"erase " MK_STR(TEXT_BASE) " +$filesize; " \
	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
	"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=your.ramdisk.u-boot\0" \
	"dtbaddr=c00000\0" \
	"dtbfile=mpc8641_hpcn.dtb\0" \
	"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
	"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
	"maxcpus=2"


	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $dtbaddr $dtbfile;" \
	"bootm $loadaddr - $dtbaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $dtbaddr $dtbfile;" \
	"bootm $loadaddr $ramdiskaddr $dtbaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

	#endif /* __CONFIG_H */