| // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| /* |
| * (C) Copyright 2017 Rockchip Electronics Co., Ltd. |
| */ |
| #include <common.h> |
| #include <clk.h> |
| #include <debug_uart.h> |
| #include <dm.h> |
| #include <dt-structs.h> |
| #include <init.h> |
| #include <log.h> |
| #include <ram.h> |
| #include <regmap.h> |
| #include <syscon.h> |
| #include <asm/io.h> |
| #include <asm/arch-rockchip/clock.h> |
| #include <asm/arch-rockchip/cru_rk3328.h> |
| #include <asm/arch-rockchip/grf_rk3328.h> |
| #include <asm/arch-rockchip/sdram.h> |
| #include <asm/arch-rockchip/sdram_rk3328.h> |
| #include <asm/arch-rockchip/uart.h> |
| #include <linux/delay.h> |
| |
| struct dram_info { |
| #ifdef CONFIG_TPL_BUILD |
| struct ddr_pctl_regs *pctl; |
| struct ddr_phy_regs *phy; |
| struct clk ddr_clk; |
| struct rk3328_cru *cru; |
| struct msch_regs *msch; |
| struct rk3328_ddr_grf_regs *ddr_grf; |
| #endif |
| struct ram_info info; |
| struct rk3328_grf_regs *grf; |
| }; |
| |
| #ifdef CONFIG_TPL_BUILD |
| |
| struct rk3328_sdram_channel sdram_ch; |
| |
| struct rockchip_dmc_plat { |
| #if CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct dtd_rockchip_rk3328_dmc dtplat; |
| #else |
| struct rk3328_sdram_params sdram_params; |
| #endif |
| struct regmap *map; |
| }; |
| |
| #if CONFIG_IS_ENABLED(OF_PLATDATA) |
| static int conv_of_plat(struct udevice *dev) |
| { |
| struct rockchip_dmc_plat *plat = dev_get_plat(dev); |
| struct dtd_rockchip_rk3328_dmc *dtplat = &plat->dtplat; |
| int ret; |
| |
| ret = regmap_init_mem_plat(dev, dtplat->reg, |
| ARRAY_SIZE(dtplat->reg) / 2, &plat->map); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| #endif |
| |
| static void rkclk_ddr_reset(struct dram_info *dram, |
| u32 ctl_srstn, u32 ctl_psrstn, |
| u32 phy_srstn, u32 phy_psrstn) |
| { |
| writel(ddrctrl_srstn_req(ctl_srstn) | ddrctrl_psrstn_req(ctl_psrstn) | |
| ddrphy_srstn_req(phy_srstn) | ddrphy_psrstn_req(phy_psrstn), |
| &dram->cru->softrst_con[5]); |
| writel(ddrctrl_asrstn_req(ctl_srstn), &dram->cru->softrst_con[9]); |
| } |
| |
| static void rkclk_set_dpll(struct dram_info *dram, unsigned int hz) |
| { |
| unsigned int refdiv, postdiv1, postdiv2, fbdiv; |
| int delay = 1000; |
| u32 mhz = hz / MHZ; |
| |
| refdiv = 1; |
| if (mhz <= 300) { |
| postdiv1 = 4; |
| postdiv2 = 2; |
| } else if (mhz <= 400) { |
| postdiv1 = 6; |
| postdiv2 = 1; |
| } else if (mhz <= 600) { |
| postdiv1 = 4; |
| postdiv2 = 1; |
| } else if (mhz <= 800) { |
| postdiv1 = 3; |
| postdiv2 = 1; |
| } else if (mhz <= 1600) { |
| postdiv1 = 2; |
| postdiv2 = 1; |
| } else { |
| postdiv1 = 1; |
| postdiv2 = 1; |
| } |
| fbdiv = (mhz * refdiv * postdiv1 * postdiv2) / 24; |
| |
| writel(((0x1 << 4) << 16) | (0 << 4), &dram->cru->mode_con); |
| writel(POSTDIV1(postdiv1) | FBDIV(fbdiv), &dram->cru->dpll_con[0]); |
| writel(DSMPD(1) | POSTDIV2(postdiv2) | REFDIV(refdiv), |
| &dram->cru->dpll_con[1]); |
| |
| while (delay > 0) { |
| udelay(1); |
| if (LOCK(readl(&dram->cru->dpll_con[1]))) |
| break; |
| delay--; |
| } |
| |
| writel(((0x1 << 4) << 16) | (1 << 4), &dram->cru->mode_con); |
| } |
| |
| static void rkclk_configure_ddr(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params) |
| { |
| void __iomem *phy_base = dram->phy; |
| |
| /* choose DPLL for ddr clk source */ |
| clrbits_le32(PHY_REG(phy_base, 0xef), 1 << 7); |
| |
| /* for inno ddr phy need 2*freq */ |
| rkclk_set_dpll(dram, sdram_params->base.ddr_freq * MHZ * 2); |
| } |
| |
| /* return ddrconfig value |
| * (-1), find ddrconfig fail |
| * other, the ddrconfig value |
| * only support cs0_row >= cs1_row |
| */ |
| static u32 calculate_ddrconfig(struct rk3328_sdram_params *sdram_params) |
| { |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| u32 cs, bw, die_bw, col, row, bank; |
| u32 cs1_row; |
| u32 i, tmp; |
| u32 ddrconf = -1; |
| |
| cs = cap_info->rank; |
| bw = cap_info->bw; |
| die_bw = cap_info->dbw; |
| col = cap_info->col; |
| row = cap_info->cs0_row; |
| cs1_row = cap_info->cs1_row; |
| bank = cap_info->bk; |
| |
| if (sdram_params->base.dramtype == DDR4) { |
| /* when DDR_TEST, CS always at MSB position for easy test */ |
| if (cs == 2 && row == cs1_row) { |
| /* include 2cs cap both 2^n or both (2^n - 2^(n-2)) */ |
| tmp = ((row - 13) << 3) | (1 << 2) | (bw & 0x2) | |
| die_bw; |
| for (i = 17; i < 21; i++) { |
| if (((tmp & 0x7) == |
| (ddr4_cfg_2_rbc[i - 10] & 0x7)) && |
| ((tmp & 0x3c) <= |
| (ddr4_cfg_2_rbc[i - 10] & 0x3c))) { |
| ddrconf = i; |
| goto out; |
| } |
| } |
| } |
| |
| tmp = ((cs - 1) << 6) | ((row - 13) << 3) | (bw & 0x2) | die_bw; |
| for (i = 10; i < 17; i++) { |
| if (((tmp & 0x7) == (ddr4_cfg_2_rbc[i - 10] & 0x7)) && |
| ((tmp & 0x3c) <= (ddr4_cfg_2_rbc[i - 10] & 0x3c)) && |
| ((tmp & 0x40) <= (ddr4_cfg_2_rbc[i - 10] & 0x40))) { |
| ddrconf = i; |
| goto out; |
| } |
| } |
| } else { |
| if (bank == 2) { |
| ddrconf = 8; |
| goto out; |
| } |
| |
| /* when DDR_TEST, CS always at MSB position for easy test */ |
| if (cs == 2 && row == cs1_row) { |
| /* include 2cs cap both 2^n or both (2^n - 2^(n-2)) */ |
| for (i = 5; i < 8; i++) { |
| if ((bw + col - 11) == (ddr_cfg_2_rbc[i] & |
| 0x3)) { |
| ddrconf = i; |
| goto out; |
| } |
| } |
| } |
| |
| tmp = ((row - 13) << 4) | (1 << 2) | ((bw + col - 11) << 0); |
| for (i = 0; i < 5; i++) |
| if (((tmp & 0xf) == (ddr_cfg_2_rbc[i] & 0xf)) && |
| ((tmp & 0x30) <= (ddr_cfg_2_rbc[i] & 0x30))) { |
| ddrconf = i; |
| goto out; |
| } |
| } |
| |
| out: |
| if (ddrconf > 20) |
| printf("calculate ddrconfig error\n"); |
| |
| return ddrconf; |
| } |
| |
| /******* |
| * calculate controller dram address map, and setting to register. |
| * argument sdram_ch.ddrconf must be right value before |
| * call this function. |
| *******/ |
| static void set_ctl_address_map(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params) |
| { |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| void __iomem *pctl_base = dram->pctl; |
| |
| sdram_copy_to_reg((u32 *)(pctl_base + DDR_PCTL2_ADDRMAP0), |
| &addrmap[cap_info->ddrconfig][0], 9 * 4); |
| if (sdram_params->base.dramtype == LPDDR3 && cap_info->row_3_4) |
| setbits_le32(pctl_base + DDR_PCTL2_ADDRMAP6, 1 << 31); |
| if (sdram_params->base.dramtype == DDR4 && cap_info->bw == 0x1) |
| setbits_le32(pctl_base + DDR_PCTL2_PCCFG, 1 << 8); |
| |
| if (cap_info->rank == 1) |
| clrsetbits_le32(pctl_base + DDR_PCTL2_ADDRMAP0, 0x1f, 0x1f); |
| } |
| |
| static int data_training(struct dram_info *dram, u32 cs, u32 dramtype) |
| { |
| void __iomem *pctl_base = dram->pctl; |
| u32 dis_auto_zq = 0; |
| u32 pwrctl; |
| u32 ret; |
| |
| /* disable auto low-power */ |
| pwrctl = readl(pctl_base + DDR_PCTL2_PWRCTL); |
| writel(0, pctl_base + DDR_PCTL2_PWRCTL); |
| |
| dis_auto_zq = pctl_dis_zqcs_aref(dram->pctl); |
| |
| ret = phy_data_training(dram->phy, cs, dramtype); |
| |
| pctl_rest_zqcs_aref(dram->pctl, dis_auto_zq); |
| |
| /* restore auto low-power */ |
| writel(pwrctl, pctl_base + DDR_PCTL2_PWRCTL); |
| |
| return ret; |
| } |
| |
| static void rx_deskew_switch_adjust(struct dram_info *dram) |
| { |
| u32 i, deskew_val; |
| u32 gate_val = 0; |
| void __iomem *phy_base = dram->phy; |
| |
| for (i = 0; i < 4; i++) |
| gate_val = MAX(readl(PHY_REG(phy_base, 0xfb + i)), gate_val); |
| |
| deskew_val = (gate_val >> 3) + 1; |
| deskew_val = (deskew_val > 0x1f) ? 0x1f : deskew_val; |
| clrsetbits_le32(PHY_REG(phy_base, 0x6e), 0xc, (deskew_val & 0x3) << 2); |
| clrsetbits_le32(PHY_REG(phy_base, 0x6f), 0x7 << 4, |
| (deskew_val & 0x1c) << 2); |
| } |
| |
| static void tx_deskew_switch_adjust(struct dram_info *dram) |
| { |
| void __iomem *phy_base = dram->phy; |
| |
| clrsetbits_le32(PHY_REG(phy_base, 0x6e), 0x3, 1); |
| } |
| |
| static void set_ddrconfig(struct dram_info *dram, u32 ddrconfig) |
| { |
| writel(ddrconfig, &dram->msch->ddrconf); |
| } |
| |
| static void sdram_msch_config(struct msch_regs *msch, |
| struct sdram_msch_timings *noc_timings) |
| { |
| writel(noc_timings->ddrtiming.d32, &msch->ddrtiming); |
| |
| writel(noc_timings->ddrmode.d32, &msch->ddrmode); |
| writel(noc_timings->readlatency, &msch->readlatency); |
| |
| writel(noc_timings->activate.d32, &msch->activate); |
| writel(noc_timings->devtodev.d32, &msch->devtodev); |
| writel(noc_timings->ddr4timing.d32, &msch->ddr4_timing); |
| writel(noc_timings->agingx0, &msch->aging0); |
| writel(noc_timings->agingx0, &msch->aging1); |
| writel(noc_timings->agingx0, &msch->aging2); |
| writel(noc_timings->agingx0, &msch->aging3); |
| writel(noc_timings->agingx0, &msch->aging4); |
| writel(noc_timings->agingx0, &msch->aging5); |
| } |
| |
| static void dram_all_config(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params) |
| { |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| u32 sys_reg2 = 0; |
| u32 sys_reg3 = 0; |
| |
| set_ddrconfig(dram, cap_info->ddrconfig); |
| sdram_org_config(cap_info, &sdram_params->base, &sys_reg2, |
| &sys_reg3, 0); |
| writel(sys_reg2, &dram->grf->os_reg[2]); |
| writel(sys_reg3, &dram->grf->os_reg[3]); |
| |
| sdram_msch_config(dram->msch, &sdram_ch.noc_timings); |
| } |
| |
| static void enable_low_power(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params) |
| { |
| void __iomem *pctl_base = dram->pctl; |
| |
| /* enable upctl2 axi clock auto gating */ |
| writel(0x00800000, &dram->ddr_grf->ddr_grf_con[0]); |
| writel(0x20012001, &dram->ddr_grf->ddr_grf_con[2]); |
| /* enable upctl2 core clock auto gating */ |
| writel(0x001e001a, &dram->ddr_grf->ddr_grf_con[2]); |
| /* enable sr, pd */ |
| if (PD_IDLE == 0) |
| clrbits_le32(pctl_base + DDR_PCTL2_PWRCTL, (1 << 1)); |
| else |
| setbits_le32(pctl_base + DDR_PCTL2_PWRCTL, (1 << 1)); |
| if (SR_IDLE == 0) |
| clrbits_le32(pctl_base + DDR_PCTL2_PWRCTL, 1); |
| else |
| setbits_le32(pctl_base + DDR_PCTL2_PWRCTL, 1); |
| setbits_le32(pctl_base + DDR_PCTL2_PWRCTL, (1 << 3)); |
| } |
| |
| static int sdram_init(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params, u32 pre_init) |
| { |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| void __iomem *pctl_base = dram->pctl; |
| |
| rkclk_ddr_reset(dram, 1, 1, 1, 1); |
| udelay(10); |
| /* |
| * dereset ddr phy psrstn to config pll, |
| * if using phy pll psrstn must be dereset |
| * before config pll |
| */ |
| rkclk_ddr_reset(dram, 1, 1, 1, 0); |
| rkclk_configure_ddr(dram, sdram_params); |
| |
| /* release phy srst to provide clk to ctrl */ |
| rkclk_ddr_reset(dram, 1, 1, 0, 0); |
| udelay(10); |
| phy_soft_reset(dram->phy); |
| /* release ctrl presetn, and config ctl registers */ |
| rkclk_ddr_reset(dram, 1, 0, 0, 0); |
| pctl_cfg(dram->pctl, &sdram_params->pctl_regs, SR_IDLE, PD_IDLE); |
| cap_info->ddrconfig = calculate_ddrconfig(sdram_params); |
| set_ctl_address_map(dram, sdram_params); |
| phy_cfg(dram->phy, &sdram_params->phy_regs, &sdram_params->skew, |
| &sdram_params->base, cap_info->bw); |
| |
| /* enable dfi_init_start to init phy after ctl srstn deassert */ |
| setbits_le32(pctl_base + DDR_PCTL2_DFIMISC, (1 << 5) | (1 << 4)); |
| rkclk_ddr_reset(dram, 0, 0, 0, 0); |
| /* wait for dfi_init_done and dram init complete */ |
| while ((readl(pctl_base + DDR_PCTL2_STAT) & 0x7) == 0) |
| continue; |
| |
| /* do ddr gate training */ |
| if (data_training(dram, 0, sdram_params->base.dramtype) != 0) { |
| printf("data training error\n"); |
| return -1; |
| } |
| |
| if (sdram_params->base.dramtype == DDR4) |
| pctl_write_vrefdq(dram->pctl, 0x3, 5670, |
| sdram_params->base.dramtype); |
| |
| if (pre_init != 0) { |
| rx_deskew_switch_adjust(dram); |
| tx_deskew_switch_adjust(dram); |
| } |
| |
| dram_all_config(dram, sdram_params); |
| enable_low_power(dram, sdram_params); |
| |
| return 0; |
| } |
| |
| static u64 dram_detect_cap(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params, |
| unsigned char channel) |
| { |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| |
| /* |
| * for ddr3: ddrconf = 3 |
| * for ddr4: ddrconf = 12 |
| * for lpddr3: ddrconf = 3 |
| * default bw = 1 |
| */ |
| u32 bk, bktmp; |
| u32 col, coltmp; |
| u32 rowtmp; |
| u32 cs; |
| u32 bw = 1; |
| u32 dram_type = sdram_params->base.dramtype; |
| |
| if (dram_type != DDR4) { |
| /* detect col and bk for ddr3/lpddr3 */ |
| coltmp = 12; |
| bktmp = 3; |
| rowtmp = 16; |
| |
| if (sdram_detect_col(cap_info, coltmp) != 0) |
| goto cap_err; |
| sdram_detect_bank(cap_info, coltmp, bktmp); |
| sdram_detect_dbw(cap_info, dram_type); |
| } else { |
| /* detect bg for ddr4 */ |
| coltmp = 10; |
| bktmp = 4; |
| rowtmp = 17; |
| |
| col = 10; |
| bk = 2; |
| cap_info->col = col; |
| cap_info->bk = bk; |
| sdram_detect_bg(cap_info, coltmp); |
| } |
| |
| /* detect row */ |
| if (sdram_detect_row(cap_info, coltmp, bktmp, rowtmp) != 0) |
| goto cap_err; |
| |
| /* detect row_3_4 */ |
| sdram_detect_row_3_4(cap_info, coltmp, bktmp); |
| |
| /* bw and cs detect using data training */ |
| if (data_training(dram, 1, dram_type) == 0) |
| cs = 1; |
| else |
| cs = 0; |
| cap_info->rank = cs + 1; |
| |
| bw = 2; |
| cap_info->bw = bw; |
| |
| cap_info->cs0_high16bit_row = cap_info->cs0_row; |
| if (cs) { |
| cap_info->cs1_row = cap_info->cs0_row; |
| cap_info->cs1_high16bit_row = cap_info->cs0_row; |
| } else { |
| cap_info->cs1_row = 0; |
| cap_info->cs1_high16bit_row = 0; |
| } |
| |
| return 0; |
| cap_err: |
| return -1; |
| } |
| |
| static int sdram_init_detect(struct dram_info *dram, |
| struct rk3328_sdram_params *sdram_params) |
| { |
| u32 sys_reg = 0; |
| u32 sys_reg3 = 0; |
| struct sdram_cap_info *cap_info = &sdram_params->ch.cap_info; |
| |
| debug("Starting SDRAM initialization...\n"); |
| |
| memcpy(&sdram_ch, &sdram_params->ch, |
| sizeof(struct rk3328_sdram_channel)); |
| |
| sdram_init(dram, sdram_params, 0); |
| dram_detect_cap(dram, sdram_params, 0); |
| |
| /* modify bw, cs related timing */ |
| pctl_remodify_sdram_params(&sdram_params->pctl_regs, cap_info, |
| sdram_params->base.dramtype); |
| |
| if (cap_info->bw == 2) |
| sdram_ch.noc_timings.ddrtiming.b.bwratio = 0; |
| else |
| sdram_ch.noc_timings.ddrtiming.b.bwratio = 1; |
| |
| /* reinit sdram by real dram cap */ |
| sdram_init(dram, sdram_params, 1); |
| |
| /* redetect cs1 row */ |
| sdram_detect_cs1_row(cap_info, sdram_params->base.dramtype); |
| if (cap_info->cs1_row) { |
| sys_reg = readl(&dram->grf->os_reg[2]); |
| sys_reg3 = readl(&dram->grf->os_reg[3]); |
| SYS_REG_ENC_CS1_ROW(cap_info->cs1_row, |
| sys_reg, sys_reg3, 0); |
| writel(sys_reg, &dram->grf->os_reg[2]); |
| writel(sys_reg3, &dram->grf->os_reg[3]); |
| } |
| |
| sdram_print_ddr_info(&sdram_params->ch.cap_info, &sdram_params->base); |
| |
| return 0; |
| } |
| |
| static int rk3328_dmc_init(struct udevice *dev) |
| { |
| struct dram_info *priv = dev_get_priv(dev); |
| struct rockchip_dmc_plat *plat = dev_get_plat(dev); |
| int ret; |
| |
| #if !CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct rk3328_sdram_params *params = &plat->sdram_params; |
| #else |
| struct dtd_rockchip_rk3328_dmc *dtplat = &plat->dtplat; |
| struct rk3328_sdram_params *params = |
| (void *)dtplat->rockchip_sdram_params; |
| |
| ret = conv_of_plat(dev); |
| if (ret) |
| return ret; |
| #endif |
| priv->phy = regmap_get_range(plat->map, 0); |
| priv->pctl = regmap_get_range(plat->map, 1); |
| priv->grf = regmap_get_range(plat->map, 2); |
| priv->cru = regmap_get_range(plat->map, 3); |
| priv->msch = regmap_get_range(plat->map, 4); |
| priv->ddr_grf = regmap_get_range(plat->map, 5); |
| |
| debug("%s phy %p pctrl %p grf %p cru %p msch %p ddr_grf %p\n", |
| __func__, priv->phy, priv->pctl, priv->grf, priv->cru, |
| priv->msch, priv->ddr_grf); |
| ret = sdram_init_detect(priv, params); |
| if (ret < 0) { |
| printf("%s DRAM init failed%d\n", __func__, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int rk3328_dmc_of_to_plat(struct udevice *dev) |
| { |
| #if !CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct rockchip_dmc_plat *plat = dev_get_plat(dev); |
| int ret; |
| |
| ret = dev_read_u32_array(dev, "rockchip,sdram-params", |
| (u32 *)&plat->sdram_params, |
| sizeof(plat->sdram_params) / sizeof(u32)); |
| if (ret) { |
| printf("%s: Cannot read rockchip,sdram-params %d\n", |
| __func__, ret); |
| return ret; |
| } |
| ret = regmap_init_mem(dev, &plat->map); |
| if (ret) |
| printf("%s: regmap failed %d\n", __func__, ret); |
| #endif |
| return 0; |
| } |
| |
| #endif |
| |
| static int rk3328_dmc_probe(struct udevice *dev) |
| { |
| #ifdef CONFIG_TPL_BUILD |
| if (rk3328_dmc_init(dev)) |
| return 0; |
| #else |
| struct dram_info *priv = dev_get_priv(dev); |
| |
| priv->grf = syscon_get_first_range(ROCKCHIP_SYSCON_GRF); |
| debug("%s: grf=%p\n", __func__, priv->grf); |
| priv->info.base = CONFIG_SYS_SDRAM_BASE; |
| priv->info.size = rockchip_sdram_size( |
| (phys_addr_t)&priv->grf->os_reg[2]); |
| #endif |
| return 0; |
| } |
| |
| static int rk3328_dmc_get_info(struct udevice *dev, struct ram_info *info) |
| { |
| struct dram_info *priv = dev_get_priv(dev); |
| |
| *info = priv->info; |
| |
| return 0; |
| } |
| |
| static struct ram_ops rk3328_dmc_ops = { |
| .get_info = rk3328_dmc_get_info, |
| }; |
| |
| static const struct udevice_id rk3328_dmc_ids[] = { |
| { .compatible = "rockchip,rk3328-dmc" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(rockchip_rk3328_dmc) = { |
| .name = "rockchip_rk3328_dmc", |
| .id = UCLASS_RAM, |
| .of_match = rk3328_dmc_ids, |
| .ops = &rk3328_dmc_ops, |
| #ifdef CONFIG_TPL_BUILD |
| .of_to_plat = rk3328_dmc_of_to_plat, |
| #endif |
| .probe = rk3328_dmc_probe, |
| .priv_auto = sizeof(struct dram_info), |
| #ifdef CONFIG_TPL_BUILD |
| .plat_auto = sizeof(struct rockchip_dmc_plat), |
| #endif |
| }; |