doc/README.imximage - platform/external/u-boot - Gitiles

 ---------------------------------------------
 Imximage Boot Image generation using mkimage
 ---------------------------------------------

 This document describes how to set up a U-Boot image that can be booted
 by Freescale MX25, MX35, MX51, MX53 and MX6 processors via internal boot
 mode.

 These processors can boot directly from NAND, SPI flash and SD card flash
 using its internal boot ROM support. MX6 processors additionally support
 boot from NOR flash and SATA disks. All processors can boot from an internal
 UART, if booting from device media fails.
 Booting from NOR flash does not require to use this image type.

 For more details refer Chapter 2 - System Boot and section 2.14
 (flash header description) of the processor's manual.

 Command syntax:
 --------------
 ./tools/mkimage -l <mx u-boot_file>
 		to list the imx image file details

 ./tools/mkimage -T imximage \
 		-n <board specific configuration file> \
 		-e <execution address> -d <u-boot binary>  <output image file>

 For example, for the mx51evk board:
 ./tools/mkimage -n ./board/freescale/mx51evk/imximage.cfg \
 		-T imximage -e 0x97800000  \
 		-d u-boot.bin u-boot.imx

 You can generate directly the image when you compile u-boot with:

 $ make u-boot.imx

 The output image can be flashed on the board SPI flash or on a SD card.
 In both cases, you have to copy the image at the offset required for the
 chosen media devices (0x400 for both SPI flash or SD card).

 Please check Freescale documentation for further details.

 Board specific configuration file specifications:
 -------------------------------------------------
 1. This file must present in the $(BOARDDIR) and the name should be
 	imximage.cfg (since this is used in Makefile).
 2. This file can have empty lines and lines starting with "#" as first
 	character to put comments.
 3. This file can have configuration command lines as mentioned below,
 	any other information in this file is treated as invalid.

 Configuration command line syntax:
 ---------------------------------
 1. Each command line is must have two strings, first one command or address
 	and second one data string
 2. Following are the valid command strings and associated data strings:-
 	Command string		data string
 	--------------		-----------
 	IMXIMAGE_VERSION        1/2
 				1 is for mx25/mx35/mx51 compatible,
 				2 is for mx53/mx6 compatible,
 				others is invalid and error is generated.
 				This command need appear the fist before
 				other valid commands in configuration file.

 	BOOT_OFFSET		value

 				This command is parallel to BOOT_FROM and
 				is preferred over BOOT_FROM.

 				value:  Offset of the image header, this
 					value shall be set to one of the
 					values found in the file:
 						arch/arm/include/asm/\
 						mach-imx/imximage.cfg
 				Example:
 				BOOT_OFFSET FLASH_OFFSET_STANDARD

 	BOOT_FROM		nand/spi/sd/onenand/nor/sata

 				This command is parallel to BOOT_OFFSET and
 				is to be deprecated in favor of BOOT_OFFSET.

 				Example:
 				BOOT_FROM spi

 	CSF			value

 				Total size of CSF (Command Sequence File)
 				used for Secure Boot/ High Assurance Boot
 				(HAB).

 				Using this command will populate the IVT
 				(Initial Vector Table) CSF pointer and adjust
 				the length fields only. The CSF itself needs
 				to be generated with Freescale tools and
 				'manually' appended to the u-boot.imx file.

 				The CSF is then simply concatenated
 				to the u-boot image, making a signed bootloader,
 				that the processor can verify
 				if the fuses for the keys are burned.

 				Further infos how to configure the SOC to verify
 				the bootloader can be found in the "High
 				Assurance Boot Version Application Programming
 				Interface Reference Manual" as part of the
 				Freescale Code Signing Tool, available on the
 				manufacturer's website.

 				Example:
 				CSF 0x2000

 	DATA			type address value

 				type: word=4, halfword=2, byte=1
 				address: physycal register address
 				value: value to be set in register
 				All values are in in hexadecimal.
 				Example (write to IOMUXC):
 				DATA 4 0x73FA88a0 0x200

 The processor support up to 60 register programming commands for IMXIMAGE_VERSION 1
 and 220 register programming commands for IMXIMAGE_VERSION 2.
 An error is generated if more commands are found in the configuration file.

 3. All commands are optional to program.

 Setup a SD Card for booting
 --------------------------------

 The following example prepare a SD card with u-boot and a FAT partition
 to be used to stored the kernel to be booted.
 I will set the SD in the most compatible mode, setting it with
 255 heads and 63 sectors, as suggested from several documentation and
 howto on line (I took as reference the preparation of a SD Card for the
 Beagleboard, running u-boot as bootloader).

 You should start clearing the partitions table on the SD card. Because
 the u-boot image must be stored at the offset 0x400, it must be assured
 that there is no partition at that address. A new SD card is already
 formatted with FAT filesystem and the partition starts from the first
 cylinder, so we need to change it.

 You can do all steps with fdisk. If the device for the SD card is
 /dev/mmcblk0, the following commands make the job:

 1. Start the fdisk utility (as superuser)
 	fdisk /dev/mmcblk0

 2. Clear the actual partition

 Command (m for help): o

 3. Print card info:

 Command (m for help): p
 Disk /dev/mmcblk0: 1981 MB, 1981284352 bytes

 In my case, I have a 2 GB card. I need the size to set later the correct value
 for the cylinders.

 4. Go to expert mode:

 Command (m for help): x

 5. Set card geometry

 Expert command (m for help): h
 Number of heads (1-256, default 4): 255

 Expert command (m for help): s
 Number of sectors (1-63, default 16): 63
 Warning: setting sector offset for DOS compatiblity

 We have set 255 heads, 63 sector. We have to set the cylinder.
 The value to be set can be calculated with:

 	cilynder = <total size> / <heads> / <sectors> / <blocksize>

 in this example,
 	1981284352 / 255 / 63 / 512 = 239.x = 239


 Expert command (m for help): c
 Number of cylinders (1-1048576, default 60032): 239

 6. Leave the expert mode
 Expert command (m for help): r

 7. Set up a partition

 Now set a partition table to store the kernel or whatever you want. Of course,
 you can set additional partitions to store rootfs, data, etc.
 In my example I want to set a single partition. I must take care
 to not overwrite the space where I will put u-boot.

 Command (m for help): n
 Command action
    e   extended
    p   primary partition (1-4)
 p
 Partition number (1-4): 1
 First cylinder (1-239, default 1): 3
 Last cylinder, +cylinders or +size{K,M,G} (3-239, default 239): +100M

 Command (m for help): p

 Disk /dev/mmcblk0: 1967 MB, 1967128576 bytes
 255 heads, 63 sectors/track, 239 cylinders
 Units = cylinders of 16065 * 512 = 8225280 bytes
 Disk identifier: 0xb712a870

 	Device Boot	 Start	       End	Blocks	 Id  System
 /dev/mmcblk0p1		     3		16	112455	 83  Linux

 I have set 100MB, leaving the first 2 sectors free. I will copy u-boot
 there.

 8. Write the partition table and exit.

 Command (m for help): w
 The partition table has been altered!

 Calling ioctl() to re-read partition table.

 9. Copy u-boot.imx on the SD card

 I use dd:

 dd if=u-boot.imx of=/dev/mmcblk0 bs=512 seek=2

 This command copies the u-boot image at the address 0x400, as required
 by the processor.

 Now remove your card from the PC and go to the target. If evrything went right,
 the u-boot prompt should come after power on.

 ------------------------------------------------
 Author: Stefano babic <sbabic@denx.de>
	---------------------------------------------
	Imximage Boot Image generation using mkimage
	---------------------------------------------

	This document describes how to set up a U-Boot image that can be booted
	by Freescale MX25, MX35, MX51, MX53 and MX6 processors via internal boot
	mode.

	These processors can boot directly from NAND, SPI flash and SD card flash
	using its internal boot ROM support. MX6 processors additionally support
	boot from NOR flash and SATA disks. All processors can boot from an internal
	UART, if booting from device media fails.
	Booting from NOR flash does not require to use this image type.

	For more details refer Chapter 2 - System Boot and section 2.14
	(flash header description) of the processor's manual.

	Command syntax:
	--------------
	./tools/mkimage -l <mx u-boot_file>
	to list the imx image file details

	./tools/mkimage -T imximage \
	-n <board specific configuration file> \
	-e <execution address> -d <u-boot binary> <output image file>

	For example, for the mx51evk board:
	./tools/mkimage -n ./board/freescale/mx51evk/imximage.cfg \
	-T imximage -e 0x97800000 \
	-d u-boot.bin u-boot.imx

	You can generate directly the image when you compile u-boot with:

	$ make u-boot.imx

	The output image can be flashed on the board SPI flash or on a SD card.
	In both cases, you have to copy the image at the offset required for the
	chosen media devices (0x400 for both SPI flash or SD card).

	Please check Freescale documentation for further details.

	Board specific configuration file specifications:
	-------------------------------------------------
	1. This file must present in the $(BOARDDIR) and the name should be
	imximage.cfg (since this is used in Makefile).
	2. This file can have empty lines and lines starting with "#" as first
	character to put comments.
	3. This file can have configuration command lines as mentioned below,
	any other information in this file is treated as invalid.

	Configuration command line syntax:
	---------------------------------
	1. Each command line is must have two strings, first one command or address
	and second one data string
	2. Following are the valid command strings and associated data strings:-
	Command string data string
	-------------- -----------
	IMXIMAGE_VERSION 1/2
	1 is for mx25/mx35/mx51 compatible,
	2 is for mx53/mx6 compatible,
	others is invalid and error is generated.
	This command need appear the fist before
	other valid commands in configuration file.

	BOOT_OFFSET value

	This command is parallel to BOOT_FROM and
	is preferred over BOOT_FROM.

	value: Offset of the image header, this
	value shall be set to one of the
	values found in the file:
	arch/arm/include/asm/\
	mach-imx/imximage.cfg
	Example:
	BOOT_OFFSET FLASH_OFFSET_STANDARD

	BOOT_FROM nand/spi/sd/onenand/nor/sata

	This command is parallel to BOOT_OFFSET and
	is to be deprecated in favor of BOOT_OFFSET.

	Example:
	BOOT_FROM spi

	CSF value

	Total size of CSF (Command Sequence File)
	used for Secure Boot/ High Assurance Boot
	(HAB).

	Using this command will populate the IVT
	(Initial Vector Table) CSF pointer and adjust
	the length fields only. The CSF itself needs
	to be generated with Freescale tools and
	'manually' appended to the u-boot.imx file.

	The CSF is then simply concatenated
	to the u-boot image, making a signed bootloader,
	that the processor can verify
	if the fuses for the keys are burned.

	Further infos how to configure the SOC to verify
	the bootloader can be found in the "High
	Assurance Boot Version Application Programming
	Interface Reference Manual" as part of the
	Freescale Code Signing Tool, available on the
	manufacturer's website.

	Example:
	CSF 0x2000

	DATA type address value

	type: word=4, halfword=2, byte=1
	address: physycal register address
	value: value to be set in register
	All values are in in hexadecimal.
	Example (write to IOMUXC):
	DATA 4 0x73FA88a0 0x200

	The processor support up to 60 register programming commands for IMXIMAGE_VERSION 1
	and 220 register programming commands for IMXIMAGE_VERSION 2.
	An error is generated if more commands are found in the configuration file.

	3. All commands are optional to program.

	Setup a SD Card for booting
	--------------------------------

	The following example prepare a SD card with u-boot and a FAT partition
	to be used to stored the kernel to be booted.
	I will set the SD in the most compatible mode, setting it with
	255 heads and 63 sectors, as suggested from several documentation and
	howto on line (I took as reference the preparation of a SD Card for the
	Beagleboard, running u-boot as bootloader).

	You should start clearing the partitions table on the SD card. Because
	the u-boot image must be stored at the offset 0x400, it must be assured
	that there is no partition at that address. A new SD card is already
	formatted with FAT filesystem and the partition starts from the first
	cylinder, so we need to change it.

	You can do all steps with fdisk. If the device for the SD card is
	/dev/mmcblk0, the following commands make the job:

	1. Start the fdisk utility (as superuser)
	fdisk /dev/mmcblk0

	2. Clear the actual partition

	Command (m for help): o

	3. Print card info:

	Command (m for help): p
	Disk /dev/mmcblk0: 1981 MB, 1981284352 bytes

	In my case, I have a 2 GB card. I need the size to set later the correct value
	for the cylinders.

	4. Go to expert mode:

	Command (m for help): x

	5. Set card geometry

	Expert command (m for help): h
	Number of heads (1-256, default 4): 255

	Expert command (m for help): s
	Number of sectors (1-63, default 16): 63
	Warning: setting sector offset for DOS compatiblity

	We have set 255 heads, 63 sector. We have to set the cylinder.
	The value to be set can be calculated with:

	cilynder = <total size> / <heads> / <sectors> / <blocksize>

	in this example,
	1981284352 / 255 / 63 / 512 = 239.x = 239


	Expert command (m for help): c
	Number of cylinders (1-1048576, default 60032): 239

	6. Leave the expert mode
	Expert command (m for help): r

	7. Set up a partition

	Now set a partition table to store the kernel or whatever you want. Of course,
	you can set additional partitions to store rootfs, data, etc.
	In my example I want to set a single partition. I must take care
	to not overwrite the space where I will put u-boot.

	Command (m for help): n
	Command action
	e extended
	p primary partition (1-4)
	p
	Partition number (1-4): 1
	First cylinder (1-239, default 1): 3
	Last cylinder, +cylinders or +size{K,M,G} (3-239, default 239): +100M

	Command (m for help): p

	Disk /dev/mmcblk0: 1967 MB, 1967128576 bytes
	255 heads, 63 sectors/track, 239 cylinders
	Units = cylinders of 16065 * 512 = 8225280 bytes
	Disk identifier: 0xb712a870

	Device Boot Start End Blocks Id System
	/dev/mmcblk0p1 3 16 112455 83 Linux

	I have set 100MB, leaving the first 2 sectors free. I will copy u-boot
	there.

	8. Write the partition table and exit.

	Command (m for help): w
	The partition table has been altered!

	Calling ioctl() to re-read partition table.

	9. Copy u-boot.imx on the SD card

	I use dd:

	dd if=u-boot.imx of=/dev/mmcblk0 bs=512 seek=2

	This command copies the u-boot image at the address 0x400, as required
	by the processor.

	Now remove your card from the PC and go to the target. If evrything went right,
	the u-boot prompt should come after power on.

	------------------------------------------------
	Author: Stefano babic <sbabic@denx.de>