blob: 430af6bfa21a52d97c4a4098cbe9113b75bfff00 [file] [log] [blame]
/*
* Configuation settings for the Motorola MC5275EVB board.
*
* By Arthur Shipkowski <art@videon-central.com>
* Copyright (C) 2005 Videon Central, Inc.
*
* Based off of M5272C3 board code by Josef Baumgartner
* <josef.baumgartner@telex.de>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M5275EVB_H
#define _M5275EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MCF52x2 /* define processor family */
#define CONFIG_M5275 /* define processor type */
#define CONFIG_M5275EVB /* define board type */
#define CONFIG_MCFTMR
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CFG_ENV_OFFSET 0x4000
#define CFG_ENV_SECT_SIZE 0x2000
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_IS_EMBEDDED 1
#else
#define CFG_ENV_ADDR 0xffe04000
#define CFG_ENV_SECT_SIZE 0x2000
#define CFG_ENV_IS_IN_FLASH 1
#endif
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Available command configuration */
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_DHCP
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_LOADB
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1
#define CONFIG_MII_INIT 1
#define CFG_DISCOVER_PHY
#define CFG_RX_ETH_BUFFER 8
#define CFG_FAULT_ECHO_LINK_DOWN
#define CFG_FEC0_PINMUX 0
#define CFG_FEC0_MIIBASE CFG_FEC0_IOBASE
#define CFG_FEC1_PINMUX 0
#define CFG_FEC1_MIIBASE CFG_FEC1_IOBASE
#define MCFFEC_TOUT_LOOP 50000
#define CONFIG_HAS_ETH1
/* If CFG_DISCOVER_PHY is not defined - hardcoded */
#ifndef CFG_DISCOVER_PHY
#define FECDUPLEX FULL
#define FECSPEED _100BASET
#else
#ifndef CFG_FAULT_ECHO_LINK_DOWN
#define CFG_FAULT_ECHO_LINK_DOWN
#endif
#endif
#endif
/* I2C */
#define CONFIG_FSL_I2C
#define CONFIG_HARD_I2C /* I2C with hw support */
#undef CONFIG_SOFT_I2C
#define CFG_I2C_SPEED 80000
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_OFFSET 0x00000300
#define CFG_IMMR CFG_MBAR
#define CFG_I2C_PINMUX_REG (gpio_reg->par_feci2c)
#define CFG_I2C_PINMUX_CLR (0xFFF0)
#define CFG_I2C_PINMUX_SET (0x000F)
#ifdef CONFIG_MCFFEC
#define CONFIG_ETHADDR 00:06:3b:01:41:55
#define CONFIG_ETH1ADDR 00:0e:0c:bc:e5:60
#endif
#define CFG_PROMPT "-> "
#define CFG_LONGHELP /* undef to save memory */
#if (CONFIG_CMD_KGDB)
# define CFG_CBSIZE 1024
#else
# define CFG_CBSIZE 256
#endif
#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
#define CFG_MAXARGS 16
#define CFG_BARGSIZE CFG_CBSIZE
#define CFG_LOAD_ADDR 0x800000
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOTCOMMAND "bootm ffe40000"
#define CFG_MEMTEST_START 0x400
#define CFG_MEMTEST_END 0x380000
#define CFG_HZ 1000
#define CFG_CLK 150000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CFG_MBAR 0x40000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR 0x20000000
#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */
#define CFG_GBL_DATA_SIZE 1000 /* bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CFG_FLASH_BASE 0xffe00000
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CFG_MONITOR_BASE 0x20000
#else
#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
#endif
#define CFG_MONITOR_LEN 0x20000
#define CFG_MALLOC_LEN (256 << 10)
#define CFG_BOOTPARAMS_LEN 64*1024
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial mmap for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 11 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 1000
#define CFG_FLASH_CFI 1
#define CONFIG_FLASH_CFI_DRIVER 1
#define CFG_FLASH_SIZE 0x200000
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
#define CFG_AR0_PRELIM (CFG_FLASH_BASE >> 16)
#define CFG_CR0_PRELIM 0x1980
#define CFG_MR0_PRELIM 0x001F0001
#define CFG_AR1_PRELIM 0x3000
#define CFG_CR1_PRELIM 0x1900
#define CFG_MR1_PRELIM 0x00070001
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CFG_FECI2C 0x0FA0
#endif /* _M5275EVB_H */