blob: d73967ac1b5d0d1a2ab006ad363be7e6741fd70f [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2019 Marek Vasut <marex@denx.de>
*/
#include <dt-bindings/clock/stm32mp1-clksrc.h>
#include "stm32mp15-u-boot.dtsi"
#include "stm32mp15-ddr3-dhsom-2x1Gb-1066-binG.dtsi"
#include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi"
#include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi"
/delete-node/ &ksz8851;
/ {
aliases {
i2c1 = &i2c2;
i2c3 = &i2c4;
i2c4 = &i2c5;
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
spi0 = &qspi;
usb0 = &usbotg_hs;
eeprom0 = &eeprom0;
ethernet1 = &ks8851;
};
config {
u-boot,boot-led = "heartbeat";
u-boot,error-led = "error";
st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
dh,som-coding-gpios = <&gpiof 12 0>, <&gpiof 13 0>, <&gpiof 15 0>;
dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>;
};
/* This is actually on FMC2, but we do not have bus driver for that */
ks8851: ks8851mll@64000000 {
compatible = "micrel,ks8851-mll";
reg = <0x64000000 0x20000>;
};
};
&ethernet0 {
phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
/delete-property/ st,eth-ref-clk-sel;
};
&ethernet0_rmii_pins_a {
pins1 {
pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
<STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
<STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
<STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */
<STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
<STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
};
};
&i2c4 {
u-boot,dm-pre-reloc;
u-boot,dm-spl;
eeprom0: eeprom@50 {
};
};
&i2c4_pins_a {
u-boot,dm-pre-reloc;
pins {
u-boot,dm-pre-reloc;
};
};
&phy0 {
/delete-property/ reset-gpios;
};
&pinctrl {
/* These should bound to FMC2 bus driver, but we do not have one */
pinctrl-0 = <&fmc_pins_b &mco2_pins_a>;
pinctrl-1 = <&fmc_sleep_pins_b &mco2_sleep_pins_a>;
pinctrl-names = "default", "sleep";
mco2_pins_a: mco2-0 {
pins {
pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
bias-disable;
drive-push-pull;
slew-rate = <2>;
};
};
mco2_sleep_pins_a: mco2-sleep-0 {
pins {
pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */
};
};
};
&pmic {
u-boot,dm-pre-reloc;
u-boot,dm-spl;
regulators {
u-boot,dm-spl;
};
};
&flash0 {
u-boot,dm-spl;
};
&qspi {
u-boot,dm-spl;
};
&qspi_clk_pins_a {
u-boot,dm-spl;
pins {
u-boot,dm-spl;
};
};
&qspi_bk1_pins_a {
u-boot,dm-spl;
pins1 {
u-boot,dm-spl;
};
pins2 {
u-boot,dm-spl;
};
};
&qspi_bk2_pins_a {
u-boot,dm-spl;
pins1 {
u-boot,dm-spl;
};
pins2 {
u-boot,dm-spl;
};
};
&rcc {
st,clksrc = <
CLK_MPU_PLL1P
CLK_AXI_PLL2P
CLK_MCU_PLL3P
CLK_PLL12_HSE
CLK_PLL3_HSE
CLK_PLL4_HSE
CLK_RTC_LSE
CLK_MCO1_DISABLED
CLK_MCO2_PLL4P
>;
st,clkdiv = <
1 /*MPU*/
0 /*AXI*/
0 /*MCU*/
1 /*APB1*/
1 /*APB2*/
1 /*APB3*/
1 /*APB4*/
2 /*APB5*/
23 /*RTC*/
0 /*MCO1*/
1 /*MCO2*/
>;
st,pkcs = <
CLK_CKPER_HSE
CLK_FMC_ACLK
CLK_QSPI_ACLK
CLK_ETH_PLL4P
CLK_SDMMC12_PLL4P
CLK_DSI_DSIPLL
CLK_STGEN_HSE
CLK_USBPHY_HSE
CLK_SPI2S1_PLL3Q
CLK_SPI2S23_PLL3Q
CLK_SPI45_HSI
CLK_SPI6_HSI
CLK_I2C46_HSI
CLK_SDMMC3_PLL4P
CLK_USBO_USBPHY
CLK_ADC_CKPER
CLK_CEC_LSE
CLK_I2C12_HSI
CLK_I2C35_HSI
CLK_UART1_HSI
CLK_UART24_HSI
CLK_UART35_HSI
CLK_UART6_HSI
CLK_UART78_HSI
CLK_SPDIF_PLL4P
CLK_FDCAN_PLL4R
CLK_SAI1_PLL3Q
CLK_SAI2_PLL3Q
CLK_SAI3_PLL3Q
CLK_SAI4_PLL3Q
CLK_RNG1_LSI
CLK_RNG2_LSI
CLK_LPTIM1_PCLK1
CLK_LPTIM23_PCLK3
CLK_LPTIM45_LSE
>;
/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
pll2: st,pll@1 {
compatible = "st,stm32mp1-pll";
reg = <1>;
cfg = < 2 65 1 0 0 PQR(1,1,1) >;
frac = < 0x1400 >;
u-boot,dm-pre-reloc;
};
/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
pll3: st,pll@2 {
compatible = "st,stm32mp1-pll";
reg = <2>;
cfg = < 1 33 1 16 36 PQR(1,1,1) >;
frac = < 0x1a04 >;
u-boot,dm-pre-reloc;
};
/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
pll4: st,pll@3 {
compatible = "st,stm32mp1-pll";
reg = <3>;
cfg = < 1 49 5 11 11 PQR(1,1,1) >;
u-boot,dm-pre-reloc;
};
};
&sdmmc1 {
u-boot,dm-spl;
st,use-ckin;
st,cmd-gpios = <&gpiod 2 0>;
st,ck-gpios = <&gpioc 12 0>;
st,ckin-gpios = <&gpioe 4 0>;
};
&sdmmc1_b4_pins_a {
u-boot,dm-spl;
pins1 {
u-boot,dm-spl;
};
pins2 {
u-boot,dm-spl;
};
};
&sdmmc1_dir_pins_a {
u-boot,dm-spl;
pins1 {
u-boot,dm-spl;
};
pins2 {
u-boot,dm-spl;
};
};
&sdmmc2 {
u-boot,dm-spl;
};
&sdmmc2_b4_pins_a {
u-boot,dm-spl;
pins {
u-boot,dm-spl;
};
};
&sdmmc2_d47_pins_a {
u-boot,dm-spl;
pins {
u-boot,dm-spl;
};
};
&uart4 {
u-boot,dm-pre-reloc;
};
&uart4_pins_a {
u-boot,dm-pre-reloc;
pins1 {
u-boot,dm-pre-reloc;
};
pins2 {
u-boot,dm-pre-reloc;
/* pull-up on rx to avoid floating level */
bias-pull-up;
};
};
&reg11 {
u-boot,dm-spl;
};
&reg18 {
u-boot,dm-spl;
};
&usb33 {
u-boot,dm-spl;
};
&usbotg_hs_pins_a {
u-boot,dm-spl;
};
&usbotg_hs {
u-boot,dm-spl;
};
&usbphyc {
u-boot,dm-spl;
};
&usbphyc_port0 {
u-boot,dm-spl;
};
&usbphyc_port1 {
u-boot,dm-spl;
};
&vdd_usb {
u-boot,dm-spl;
};