blob: 3ab8d559bfd067bed55cb722bda118e4e4064cfc [file] [log] [blame]
/*
* Copyright (C) 2013 Samsung Electronics
*
* Configuration settings for the SAMSUNG EXYNOS5 board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_EXYNOS5_COMMON_H
#define __CONFIG_EXYNOS5_COMMON_H
#define CONFIG_EXYNOS5 /* Exynos5 Family */
#include "exynos-common.h"
#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_EXYNOS_SPL
/* Allow tracing to be enabled */
#define CONFIG_TRACE
#define CONFIG_CMD_TRACE
#define CONFIG_TRACE_BUFFER_SIZE (16 << 20)
#define CONFIG_TRACE_EARLY_SIZE (8 << 20)
#define CONFIG_TRACE_EARLY
#define CONFIG_TRACE_EARLY_ADDR 0x50000000
/* Enable ACE acceleration for SHA1 and SHA256 */
#define CONFIG_EXYNOS_ACE_SHA
#define CONFIG_SHA_HW_ACCEL
/* Power Down Modes */
#define S5P_CHECK_SLEEP 0x00000BAD
#define S5P_CHECK_DIDLE 0xBAD00000
#define S5P_CHECK_LPA 0xABAD0000
/* Offset for inform registers */
#define INFORM0_OFFSET 0x800
#define INFORM1_OFFSET 0x804
#define INFORM2_OFFSET 0x808
#define INFORM3_OFFSET 0x80c
/* select serial console configuration */
#define CONFIG_BAUDRATE 115200
#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000
#define CONFIG_SILENT_CONSOLE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_CONSOLE_MUX
#define CONFIG_CMD_HASH
/* Thermal Management Unit */
#define CONFIG_EXYNOS_TMU
#define CONFIG_CMD_DTT
#define CONFIG_TMU_CMD_DTT
/* TPM */
#define CONFIG_TPM
#define CONFIG_CMD_TPM
#define CONFIG_TPM_TIS_I2C
#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3
#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20
/* MMC SPL */
#define COPY_BL2_FNPTR_ADDR 0x02020030
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
/* specific .lds file */
#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
/* Boot Argument Buffer Size */
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
#define CONFIG_RD_LVL
#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE
#define CONFIG_SYS_MONITOR_BASE 0x00000000
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_SECURE_BL1_ONLY
/* Secure FW size configuration */
#ifdef CONFIG_SECURE_BL1_ONLY
#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
#else
#define CONFIG_SEC_FW_SIZE 0
#endif
/* Configuration of BL1, BL2, ENV Blocks on mmc */
#define CONFIG_RES_BLOCK_SIZE (512)
#define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
#define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
/* U-boot copy size from boot Media to DRAM.*/
#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
/* I2C */
/* TODO(sjg@chromium.org): Move these two options to Kconfig */
#define CONFIG_DM_I2C
#define CONFIG_DM_I2C_COMPAT
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* SPI */
#ifdef CONFIG_SPI_FLASH
#define CONFIG_EXYNOS_SPI
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_SPI_FLASH_WINBOND
#define CONFIG_SPI_FLASH_GIGADEVICE
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_SPEED 50000000
#define EXYNOS5_SPI_NUM_CONTROLLERS 5
#define CONFIG_OF_SPI
#endif
#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
#define CONFIG_ENV_SPI_BUS 1
#define CONFIG_ENV_SPI_MAX_HZ 50000000
#endif
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
#define CONFIG_SMC911X
#define CONFIG_SMC911X_BASE 0x5000000
#define CONFIG_SMC911X_16_BIT
#define CONFIG_ENV_SROM_BANK 1
#endif /*CONFIG_CMD_NET*/
/* SHA hashing */
#define CONFIG_CMD_HASH
#define CONFIG_HASH_VERIFY
#define CONFIG_SHA1
#define CONFIG_SHA256
/* Enable Time Command */
#define CONFIG_CMD_TIME
#define CONFIG_CMD_GPIO
/* USB */
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_SMSC95XX
/* USB boot mode */
#define CONFIG_USB_BOOTING
#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070
#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002
#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018
/* Enable FIT support and comparison */
#define CONFIG_FIT
#define CONFIG_FIT_BEST_MATCH
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#ifndef MEM_LAYOUT_ENV_SETTINGS
/* 2GB RAM, bootm size of 256M, load scripts after that */
#define MEM_LAYOUT_ENV_SETTINGS \
"bootm_size=0x10000000\0" \
"kernel_addr_r=0x42000000\0" \
"fdt_addr_r=0x43000000\0" \
"ramdisk_addr_r=0x43300000\0" \
"scriptaddr=0x50000000\0" \
"pxefile_addr_r=0x51000000\0"
#endif
#ifndef EXYNOS_DEVICE_SETTINGS
#define EXYNOS_DEVICE_SETTINGS \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0"
#endif
#ifndef EXYNOS_FDTFILE_SETTING
#define EXYNOS_FDTFILE_SETTING
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
EXYNOS_DEVICE_SETTINGS \
EXYNOS_FDTFILE_SETTING \
MEM_LAYOUT_ENV_SETTINGS \
BOOTENV
#endif /* __CONFIG_EXYNOS5_COMMON_H */