blob: 61bfea3fab658099e6cb540ed32325beec86a37b [file] [log] [blame]
/*
* (C) Copyright 2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* define DEBUG for debugging output (obviously ;-)) */
#if 0
#define DEBUG
#endif
#include <common.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/ppc4xx-gpio.h>
extern void board_pll_init_f(void);
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
static void cram_bcr_write(u32 wr_val)
{
wr_val <<= 2;
/* set CRAM_CRE to 1 */
gpio_write_bit(CONFIG_SYS_GPIO_CRAM_CRE, 1);
/* Write BCR to CRAM on CS1 */
out32(wr_val + 0x00200000, 0);
debug("CRAM VAL: %08x for CS1 ", wr_val + 0x00200000);
/* Write BCR to CRAM on CS2 */
out32(wr_val + 0x02200000, 0);
debug("CRAM VAL: %08x for CS2\n", wr_val + 0x02200000);
sync();
eieio();
/* set CRAM_CRE back to 0 (normal operation) */
gpio_write_bit(CONFIG_SYS_GPIO_CRAM_CRE, 0);
return;
}
#endif
phys_size_t initdram(int board_type)
{
#if defined(CONFIG_NAND_SPL)
u32 reg;
/* don't reinit PLL when booting via I2C bootstrap option */
mfsdr(SDR0_PINSTP, reg);
if (reg != 0xf0000000)
board_pll_init_f();
#endif
#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
int i;
u32 val;
/* 1. EBC need to program READY, CLK, ADV for ASync mode */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_CRE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0);
gpio_config(CONFIG_SYS_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
/* 2. EBC in Async mode */
mtebc(PB1AP, 0x078F1EC0);
mtebc(PB2AP, 0x078F1EC0);
mtebc(PB1CR, 0x000BC000);
mtebc(PB2CR, 0x020BC000);
/* 3. Set CRAM in Sync mode */
cram_bcr_write(0x7012); /* CRAM burst setting */
/* 4. EBC in Sync mode */
mtebc(PB1AP, 0x9C0201C0);
mtebc(PB2AP, 0x9C0201C0);
/* Set GPIO pins back to alternate function */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
/* Config EBC to use RDY */
mfsdr(SDR0_ULTRA0, val);
mtsdr(SDR0_ULTRA0, val | SDR_ULTRA0_EBCRDYEN);
/* Wait a short while, since for NAND booting this is too fast */
for (i=0; i<200000; i++)
;
#endif
return (CONFIG_SYS_MBYTES_RAM << 20);
}