blob: 685eb7d0251ec719bc8950f8f8d1fa219ee52e9f [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
*
* Based on original Kirkwood support which is
* (C) Copyright 2009
* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*/
#ifndef _CONFIG_EDMINIV2_H
#define _CONFIG_EDMINIV2_H
/*
* SPL
*/
#define CONFIG_SPL_MAX_SIZE 0x0000fff0
#define CONFIG_SPL_STACK 0x00020000
#define CONFIG_SPL_BSS_START_ADDR 0x00020000
#define CONFIG_SPL_BSS_MAX_SIZE 0x0001ffff
#define CONFIG_SYS_SPL_MALLOC_START 0x00040000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x0001ffff
#define CONFIG_SYS_UBOOT_BASE 0xfff90000
#define CONFIG_SYS_UBOOT_START 0x00800000
/*
* High Level Configuration Options (easy to change)
*/
#include <asm/arch/orion5x.h>
/*
* CLKs configurations
*/
/*
* Board-specific values for Orion5x MPP low level init:
* - MPPs 12 to 15 are SATA LEDs (mode 5)
* - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
* MPP16 to MPP19, mode 0 for others
*/
#define ORION5X_MPP0_7 0x00000003
#define ORION5X_MPP8_15 0x55550000
#define ORION5X_MPP16_23 0x00005555
/*
* Board-specific values for Orion5x GPIO low level init:
* - GPIO3 is input (RTC interrupt)
* - GPIO16 is Power LED control (0 = on, 1 = off)
* - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
* - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
* - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
* - GPIO22 is SATA disk power status ()
* - GPIO23 is supply status for SATA disk ()
* - GPIO24 is supply control for board (write 1 to power off)
* Last GPIO is 25, further bits are supposed to be 0.
* Enable mask has ones for INPUT, 0 for OUTPUT.
* Default is LED ON, board ON :)
*/
#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
#define ORION5X_GPIO_OUT_VALUE 0x00000000
#define ORION5X_GPIO_IN_POLARITY 0x000000d0
/*
* NS16550 Configuration
*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
#define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE
/*
* Serial Port configuration
* The following definitions let you select what serial you want to use
* for your console driver.
*/
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
/*
* FLASH configuration
*/
#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */
#define CONFIG_SYS_FLASH_BASE 0xfff80000
/* auto boot */
/*
* Network
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
#define CONFIG_PHY_BASE_ADR 0x8
#endif
/*
* IDE
*/
#ifdef CONFIG_IDE
#define __io
/* Data, registers and alternate blocks are at the same offset */
/* Each 8-bit ATA register is aligned to a 4-bytes address */
/* Controller supports 48-bits LBA addressing */
#define CONFIG_LBA48
/* A single bus, a single device */
/* ATA registers base is at SATA controller base */
/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
/* end of IDE defines */
#endif /* CMD_IDE */
/*
* Common USB/EHCI configuration
*/
#ifdef CONFIG_CMD_USB
#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
#endif /* CONFIG_CMD_USB */
/*
* I2C related stuff
*/
#ifdef CONFIG_CMD_I2C
#define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE
#endif
/*
* Environment variables configurations
*/
/* Enable command line editing */
/* provide extensive help */
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
#endif /* _CONFIG_EDMINIV2_H */