| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. |
| * Based on mx6qsabrelite.c file |
| * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com> |
| * Leo Sartre, <lsartre@adeneo-embedded.com> |
| */ |
| |
| #include <common.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/iomux.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <asm/gpio.h> |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <asm/mach-imx/sata.h> |
| #include <asm/mach-imx/boot_mode.h> |
| #include <asm/mach-imx/mxc_i2c.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/arch/mxc_hdmi.h> |
| #include <asm/arch/crm_regs.h> |
| #include <mmc.h> |
| #include <fsl_esdhc_imx.h> |
| #include <i2c.h> |
| #include <input.h> |
| #include <power/pmic.h> |
| #include <power/pfuze100_pmic.h> |
| #include <linux/fb.h> |
| #include <ipu_pixfmt.h> |
| #include <malloc.h> |
| #include <miiphy.h> |
| #include <netdev.h> |
| #include <micrel.h> |
| #include <spi_flash.h> |
| #include <spi.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |\ |
| PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |\ |
| PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ |
| PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ |
| PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ |
| PAD_CTL_ODE | PAD_CTL_SRE_FAST) |
| |
| #define SPI_PAD_CTRL (PAD_CTL_HYS | \ |
| PAD_CTL_SPEED_MED | \ |
| PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) |
| |
| #define MX6Q_QMX6_PFUZE_MUX IMX_GPIO_NR(6, 9) |
| |
| |
| #define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ |
| PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ |
| PAD_CTL_DSE_40ohm | PAD_CTL_HYS) |
| |
| int dram_init(void) |
| { |
| gd->ram_size = imx_ddr_size(); |
| |
| return 0; |
| } |
| |
| static iomux_v3_cfg_t const uart2_pads[] = { |
| IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| }; |
| |
| #ifndef CONFIG_SPL_BUILD |
| static iomux_v3_cfg_t const usdhc2_pads[] = { |
| IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const usdhc3_pads[] = { |
| IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| }; |
| #endif |
| |
| static iomux_v3_cfg_t const usdhc4_pads[] = { |
| IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const usb_otg_pads[] = { |
| IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t enet_pads_ksz9031[] = { |
| IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t enet_pads_final_ksz9031[] = { |
| IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t enet_pads_ar8035[] = { |
| IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const ecspi1_pads[] = { |
| IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| #define PC MUX_PAD_CTRL(I2C_PAD_CTRL) |
| struct i2c_pads_info mx6q_i2c_pad_info1 = { |
| .scl = { |
| .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC, |
| .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC, |
| .gp = IMX_GPIO_NR(4, 12) |
| }, |
| .sda = { |
| .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC, |
| .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC, |
| .gp = IMX_GPIO_NR(4, 13) |
| } |
| }; |
| |
| struct i2c_pads_info mx6dl_i2c_pad_info1 = { |
| .scl = { |
| .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC, |
| .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC, |
| .gp = IMX_GPIO_NR(4, 12) |
| }, |
| .sda = { |
| .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC, |
| .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC, |
| .gp = IMX_GPIO_NR(4, 13) |
| } |
| }; |
| |
| #define I2C_PMIC 1 /* I2C2 port is used to connect to the PMIC */ |
| |
| struct interface_level { |
| char *name; |
| uchar value; |
| }; |
| |
| static struct interface_level mipi_levels[] = { |
| {"0V0", 0x00}, |
| {"2V5", 0x17}, |
| }; |
| |
| /* setup board specific PMIC */ |
| int power_init_board(void) |
| { |
| struct pmic *p; |
| u32 id1, id2, i; |
| int ret; |
| char const *lv_mipi; |
| |
| /* configure I2C multiplexer */ |
| gpio_direction_output(MX6Q_QMX6_PFUZE_MUX, 1); |
| |
| power_pfuze100_init(I2C_PMIC); |
| p = pmic_get("PFUZE100"); |
| if (!p) |
| return -EINVAL; |
| |
| ret = pmic_probe(p); |
| if (ret) |
| return ret; |
| |
| pmic_reg_read(p, PFUZE100_DEVICEID, &id1); |
| pmic_reg_read(p, PFUZE100_REVID, &id2); |
| printf("PFUZE100 Rev. [%02x/%02x] detected\n", id1, id2); |
| |
| if (id2 >= 0x20) |
| return 0; |
| |
| /* set level of MIPI if specified */ |
| lv_mipi = env_get("lv_mipi"); |
| if (lv_mipi) |
| return 0; |
| |
| for (i = 0; i < ARRAY_SIZE(mipi_levels); i++) { |
| if (!strcmp(mipi_levels[i].name, lv_mipi)) { |
| printf("set MIPI level %s\n", mipi_levels[i].name); |
| ret = pmic_reg_write(p, PFUZE100_VGEN4VOL, |
| mipi_levels[i].value); |
| if (ret) |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| int board_eth_init(bd_t *bis) |
| { |
| struct phy_device *phydev; |
| struct mii_dev *bus; |
| unsigned short id1, id2; |
| int ret; |
| |
| /* check whether KSZ9031 or AR8035 has to be configured */ |
| SETUP_IOMUX_PADS(enet_pads_ar8035); |
| |
| /* phy reset */ |
| gpio_direction_output(IMX_GPIO_NR(3, 23), 0); |
| udelay(2000); |
| gpio_set_value(IMX_GPIO_NR(3, 23), 1); |
| udelay(500); |
| |
| bus = fec_get_miibus(IMX_FEC_BASE, -1); |
| if (!bus) |
| return -EINVAL; |
| phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); |
| if (!phydev) { |
| printf("Error: phy device not found.\n"); |
| ret = -ENODEV; |
| goto free_bus; |
| } |
| |
| /* get the PHY id */ |
| id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); |
| id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); |
| |
| if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { |
| /* re-configure for Micrel KSZ9031 */ |
| printf("configure Micrel KSZ9031 Ethernet Phy at address %d\n", |
| phydev->addr); |
| |
| /* phy reset: gpio3-23 */ |
| gpio_set_value(IMX_GPIO_NR(3, 23), 0); |
| gpio_set_value(IMX_GPIO_NR(6, 30), (phydev->addr >> 2)); |
| gpio_set_value(IMX_GPIO_NR(6, 25), 1); |
| gpio_set_value(IMX_GPIO_NR(6, 27), 1); |
| gpio_set_value(IMX_GPIO_NR(6, 28), 1); |
| gpio_set_value(IMX_GPIO_NR(6, 29), 1); |
| SETUP_IOMUX_PADS(enet_pads_ksz9031); |
| gpio_set_value(IMX_GPIO_NR(6, 24), 1); |
| udelay(500); |
| gpio_set_value(IMX_GPIO_NR(3, 23), 1); |
| SETUP_IOMUX_PADS(enet_pads_final_ksz9031); |
| } else if ((id1 == 0x004d) && (id2 == 0xd072)) { |
| /* configure Atheros AR8035 - actually nothing to do */ |
| printf("configure Atheros AR8035 Ethernet Phy at address %d\n", |
| phydev->addr); |
| } else { |
| printf("Unknown Ethernet-Phy: 0x%04x 0x%04x\n", id1, id2); |
| ret = -EINVAL; |
| goto free_phydev; |
| } |
| |
| ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev); |
| if (ret) |
| goto free_phydev; |
| |
| return 0; |
| |
| free_phydev: |
| free(phydev); |
| free_bus: |
| free(bus); |
| return ret; |
| } |
| |
| int mx6_rgmii_rework(struct phy_device *phydev) |
| { |
| unsigned short id1, id2; |
| unsigned short val; |
| |
| /* check whether KSZ9031 or AR8035 has to be configured */ |
| id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2); |
| id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3); |
| |
| if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) { |
| /* finalize phy configuration for Micrel KSZ9031 */ |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 4); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x0000); |
| |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 5); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_REG); |
| |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 6); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0xFFFF); |
| |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 8); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3FFF); |
| |
| /* fix KSZ9031 link up issue */ |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x0); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x4); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x6); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_REG); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x1A80); |
| } |
| |
| if ((id1 == 0x004d) && (id2 == 0xd072)) { |
| /* enable AR8035 ouput a 125MHz clk from CLK_25M */ |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x7); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_DATA_POST_INC_RW | 0x16); |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC | 0x7); |
| val = phy_read(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA); |
| val &= 0xfe63; |
| val |= 0x18; |
| phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, val); |
| |
| /* introduce tx clock delay */ |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); |
| val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); |
| val |= 0x0100; |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); |
| |
| /* disable hibernation */ |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0xb); |
| val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3c40); |
| } |
| return 0; |
| } |
| |
| int board_phy_config(struct phy_device *phydev) |
| { |
| mx6_rgmii_rework(phydev); |
| |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| |
| return 0; |
| } |
| |
| static void setup_iomux_uart(void) |
| { |
| SETUP_IOMUX_PADS(uart2_pads); |
| } |
| |
| #ifdef CONFIG_MXC_SPI |
| static void setup_spi(void) |
| { |
| SETUP_IOMUX_PADS(ecspi1_pads); |
| gpio_direction_output(IMX_GPIO_NR(3, 19), 0); |
| } |
| #endif |
| |
| #ifdef CONFIG_FSL_ESDHC_IMX |
| static struct fsl_esdhc_cfg usdhc_cfg[] = { |
| {USDHC2_BASE_ADDR}, |
| {USDHC3_BASE_ADDR}, |
| {USDHC4_BASE_ADDR}, |
| }; |
| |
| int board_mmc_getcd(struct mmc *mmc) |
| { |
| struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; |
| int ret = 0; |
| |
| switch (cfg->esdhc_base) { |
| case USDHC2_BASE_ADDR: |
| gpio_direction_input(IMX_GPIO_NR(1, 4)); |
| ret = !gpio_get_value(IMX_GPIO_NR(1, 4)); |
| break; |
| case USDHC3_BASE_ADDR: |
| ret = 1; /* eMMC is always present */ |
| break; |
| case USDHC4_BASE_ADDR: |
| gpio_direction_input(IMX_GPIO_NR(2, 6)); |
| ret = !gpio_get_value(IMX_GPIO_NR(2, 6)); |
| break; |
| default: |
| printf("Bad USDHC interface\n"); |
| } |
| |
| return ret; |
| } |
| |
| int board_mmc_init(bd_t *bis) |
| { |
| #ifndef CONFIG_SPL_BUILD |
| s32 status = 0; |
| int i; |
| |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); |
| usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); |
| usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); |
| |
| SETUP_IOMUX_PADS(usdhc2_pads); |
| SETUP_IOMUX_PADS(usdhc3_pads); |
| SETUP_IOMUX_PADS(usdhc4_pads); |
| |
| for (i = 0; i < ARRAY_SIZE(usdhc_cfg); i++) { |
| status = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); |
| if (status) |
| return status; |
| } |
| |
| return 0; |
| #else |
| SETUP_IOMUX_PADS(usdhc4_pads); |
| usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR; |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); |
| gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; |
| |
| return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); |
| #endif |
| } |
| #endif |
| |
| int board_ehci_hcd_init(int port) |
| { |
| switch (port) { |
| case 0: |
| SETUP_IOMUX_PADS(usb_otg_pads); |
| /* |
| * set daisy chain for otg_pin_id on 6q. |
| * for 6dl, this bit is reserved |
| */ |
| imx_iomux_set_gpr_register(1, 13, 1, 1); |
| break; |
| case 1: |
| /* nothing to do */ |
| break; |
| default: |
| printf("Invalid USB port: %d\n", port); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| int board_ehci_power(int port, int on) |
| { |
| switch (port) { |
| case 0: |
| break; |
| case 1: |
| gpio_direction_output(IMX_GPIO_NR(5, 5), on); |
| break; |
| default: |
| printf("Invalid USB port: %d\n", port); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| struct display_info_t { |
| int bus; |
| int addr; |
| int pixfmt; |
| int (*detect)(struct display_info_t const *dev); |
| void (*enable)(struct display_info_t const *dev); |
| struct fb_videomode mode; |
| }; |
| |
| static void disable_lvds(struct display_info_t const *dev) |
| { |
| struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; |
| |
| clrbits_le32(&iomux->gpr[2], IOMUXC_GPR2_LVDS_CH0_MODE_MASK | |
| IOMUXC_GPR2_LVDS_CH1_MODE_MASK); |
| } |
| |
| static void do_enable_hdmi(struct display_info_t const *dev) |
| { |
| disable_lvds(dev); |
| imx_enable_hdmi_phy(); |
| } |
| |
| static struct display_info_t const displays[] = { |
| { |
| .bus = -1, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB666, |
| .detect = NULL, |
| .enable = NULL, |
| .mode = { |
| .name = |
| "Hannstar-XGA", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED } }, |
| { |
| .bus = -1, |
| .addr = 0, |
| .pixfmt = IPU_PIX_FMT_RGB24, |
| .detect = NULL, |
| .enable = do_enable_hdmi, |
| .mode = { |
| .name = "HDMI", |
| .refresh = 60, |
| .xres = 1024, |
| .yres = 768, |
| .pixclock = 15385, |
| .left_margin = 220, |
| .right_margin = 40, |
| .upper_margin = 21, |
| .lower_margin = 7, |
| .hsync_len = 60, |
| .vsync_len = 10, |
| .sync = FB_SYNC_EXT, |
| .vmode = FB_VMODE_NONINTERLACED } } |
| }; |
| |
| int board_video_skip(void) |
| { |
| int i; |
| int ret; |
| char const *panel = env_get("panel"); |
| if (!panel) { |
| for (i = 0; i < ARRAY_SIZE(displays); i++) { |
| struct display_info_t const *dev = displays + i; |
| if (dev->detect && dev->detect(dev)) { |
| panel = dev->mode.name; |
| printf("auto-detected panel %s\n", panel); |
| break; |
| } |
| } |
| if (!panel) { |
| panel = displays[0].mode.name; |
| printf("No panel detected: default to %s\n", panel); |
| i = 0; |
| } |
| } else { |
| for (i = 0; i < ARRAY_SIZE(displays); i++) { |
| if (!strcmp(panel, displays[i].mode.name)) |
| break; |
| } |
| } |
| if (i < ARRAY_SIZE(displays)) { |
| ret = ipuv3_fb_init(&displays[i].mode, 0, displays[i].pixfmt); |
| if (!ret) { |
| if (displays[i].enable) |
| displays[i].enable(displays + i); |
| printf("Display: %s (%ux%u)\n", |
| displays[i].mode.name, displays[i].mode.xres, |
| displays[i].mode.yres); |
| } else |
| printf("LCD %s cannot be configured: %d\n", |
| displays[i].mode.name, ret); |
| } else { |
| printf("unsupported panel %s\n", panel); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static void setup_display(void) |
| { |
| struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; |
| int reg; |
| |
| enable_ipu_clock(); |
| imx_setup_hdmi(); |
| |
| /* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */ |
| setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK | |
| MXC_CCM_CCGR3_LDB_DI1_MASK); |
| |
| /* set LDB0, LDB1 clk select to 011/011 */ |
| reg = readl(&mxc_ccm->cs2cdr); |
| reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK | |
| MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); |
| reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) | |
| (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET); |
| writel(reg, &mxc_ccm->cs2cdr); |
| |
| setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV | |
| MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV); |
| |
| setbits_le32(&mxc_ccm->chsccdr, CHSCCDR_CLK_SEL_LDB_DI0 << |
| MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET | |
| CHSCCDR_CLK_SEL_LDB_DI0 << |
| MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET); |
| |
| reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES |
| | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
| | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
| | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
| | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT |
| | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
| | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
| | IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED |
| | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0; |
| writel(reg, &iomux->gpr[2]); |
| |
| reg = readl(&iomux->gpr[3]); |
| reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | |
| IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) | |
| (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << |
| IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET); |
| writel(reg, &iomux->gpr[3]); |
| } |
| |
| /* |
| * Do not overwrite the console |
| * Use always serial for U-Boot console |
| */ |
| int overwrite_console(void) |
| { |
| return 1; |
| } |
| |
| int board_early_init_f(void) |
| { |
| setup_iomux_uart(); |
| #ifdef CONFIG_MXC_SPI |
| setup_spi(); |
| #endif |
| return 0; |
| } |
| |
| int board_init(void) |
| { |
| /* address of boot parameters */ |
| gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; |
| |
| |
| if (is_mx6dq()) |
| setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1); |
| else |
| setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1); |
| |
| setup_display(); |
| |
| #ifdef CONFIG_SATA |
| setup_sata(); |
| #endif |
| |
| return 0; |
| } |
| |
| int checkboard(void) |
| { |
| char *type = "unknown"; |
| |
| if (is_cpu_type(MXC_CPU_MX6Q)) |
| type = "Quad"; |
| else if (is_cpu_type(MXC_CPU_MX6D)) |
| type = "Dual"; |
| else if (is_cpu_type(MXC_CPU_MX6DL)) |
| type = "Dual-Lite"; |
| else if (is_cpu_type(MXC_CPU_MX6SOLO)) |
| type = "Solo"; |
| |
| printf("Board: conga-QMX6 %s\n", type); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_MXC_SPI |
| int board_spi_cs_gpio(unsigned bus, unsigned cs) |
| { |
| return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -EINVAL; |
| } |
| #endif |
| |
| #ifdef CONFIG_CMD_BMODE |
| static const struct boot_mode board_boot_modes[] = { |
| /* 4 bit bus width */ |
| {"mmc0", MAKE_CFGVAL(0x50, 0x20, 0x00, 0x00)}, |
| {"mmc1", MAKE_CFGVAL(0x50, 0x38, 0x00, 0x00)}, |
| {NULL, 0}, |
| }; |
| #endif |
| |
| int misc_init_r(void) |
| { |
| #ifdef CONFIG_CMD_BMODE |
| add_board_boot_modes(board_boot_modes); |
| #endif |
| return 0; |
| } |
| |
| int board_late_init(void) |
| { |
| #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG |
| if (is_mx6dq()) |
| env_set("board_rev", "MX6Q"); |
| else |
| env_set("board_rev", "MX6DL"); |
| #endif |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_SPL_BUILD |
| #include <asm/arch/mx6-ddr.h> |
| #include <spl.h> |
| #include <linux/libfdt.h> |
| #include <spi_flash.h> |
| #include <spi.h> |
| |
| const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = { |
| .dram_sdclk_0 = 0x00000030, |
| .dram_sdclk_1 = 0x00000030, |
| .dram_cas = 0x00000030, |
| .dram_ras = 0x00000030, |
| .dram_reset = 0x00000030, |
| .dram_sdcke0 = 0x00003000, |
| .dram_sdcke1 = 0x00003000, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = 0x00000030, |
| .dram_sdodt1 = 0x00000030, |
| .dram_sdqs0 = 0x00000030, |
| .dram_sdqs1 = 0x00000030, |
| .dram_sdqs2 = 0x00000030, |
| .dram_sdqs3 = 0x00000030, |
| .dram_sdqs4 = 0x00000030, |
| .dram_sdqs5 = 0x00000030, |
| .dram_sdqs6 = 0x00000030, |
| .dram_sdqs7 = 0x00000030, |
| .dram_dqm0 = 0x00000030, |
| .dram_dqm1 = 0x00000030, |
| .dram_dqm2 = 0x00000030, |
| .dram_dqm3 = 0x00000030, |
| .dram_dqm4 = 0x00000030, |
| .dram_dqm5 = 0x00000030, |
| .dram_dqm6 = 0x00000030, |
| .dram_dqm7 = 0x00000030, |
| }; |
| |
| static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = { |
| .dram_sdclk_0 = 0x00000030, |
| .dram_sdclk_1 = 0x00000030, |
| .dram_cas = 0x00000030, |
| .dram_ras = 0x00000030, |
| .dram_reset = 0x00000030, |
| .dram_sdcke0 = 0x00003000, |
| .dram_sdcke1 = 0x00003000, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = 0x00000030, |
| .dram_sdodt1 = 0x00000030, |
| .dram_sdqs0 = 0x00000030, |
| .dram_sdqs1 = 0x00000030, |
| .dram_sdqs2 = 0x00000030, |
| .dram_sdqs3 = 0x00000030, |
| .dram_sdqs4 = 0x00000030, |
| .dram_sdqs5 = 0x00000030, |
| .dram_sdqs6 = 0x00000030, |
| .dram_sdqs7 = 0x00000030, |
| .dram_dqm0 = 0x00000030, |
| .dram_dqm1 = 0x00000030, |
| .dram_dqm2 = 0x00000030, |
| .dram_dqm3 = 0x00000030, |
| .dram_dqm4 = 0x00000030, |
| .dram_dqm5 = 0x00000030, |
| .dram_dqm6 = 0x00000030, |
| .dram_dqm7 = 0x00000030, |
| }; |
| |
| const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = { |
| .grp_ddr_type = 0x000C0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = 0x00000030, |
| .grp_ctlds = 0x00000030, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = 0x00000030, |
| .grp_b1ds = 0x00000030, |
| .grp_b2ds = 0x00000030, |
| .grp_b3ds = 0x00000030, |
| .grp_b4ds = 0x00000030, |
| .grp_b5ds = 0x00000030, |
| .grp_b6ds = 0x00000030, |
| .grp_b7ds = 0x00000030, |
| }; |
| |
| static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { |
| .grp_ddr_type = 0x000c0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = 0x00000030, |
| .grp_ctlds = 0x00000030, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = 0x00000030, |
| .grp_b1ds = 0x00000030, |
| .grp_b2ds = 0x00000030, |
| .grp_b3ds = 0x00000030, |
| .grp_b4ds = 0x00000030, |
| .grp_b5ds = 0x00000030, |
| .grp_b6ds = 0x00000030, |
| .grp_b7ds = 0x00000030, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6q_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x0016001A, |
| .p0_mpwldectrl1 = 0x0023001C, |
| .p1_mpwldectrl0 = 0x0028003A, |
| .p1_mpwldectrl1 = 0x001F002C, |
| .p0_mpdgctrl0 = 0x43440354, |
| .p0_mpdgctrl1 = 0x033C033C, |
| .p1_mpdgctrl0 = 0x43300368, |
| .p1_mpdgctrl1 = 0x03500330, |
| .p0_mprddlctl = 0x3228242E, |
| .p1_mprddlctl = 0x2C2C2636, |
| .p0_mpwrdlctl = 0x36323A38, |
| .p1_mpwrdlctl = 0x42324440, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00080016, |
| .p0_mpwldectrl1 = 0x001D0016, |
| .p1_mpwldectrl0 = 0x0018002C, |
| .p1_mpwldectrl1 = 0x000D001D, |
| .p0_mpdgctrl0 = 0x43200334, |
| .p0_mpdgctrl1 = 0x0320031C, |
| .p1_mpdgctrl0 = 0x0344034C, |
| .p1_mpdgctrl1 = 0x03380314, |
| .p0_mprddlctl = 0x3E36383A, |
| .p1_mprddlctl = 0x38363240, |
| .p0_mpwrdlctl = 0x36364238, |
| .p1_mpwrdlctl = 0x4230423E, |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6s_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00480049, |
| .p0_mpwldectrl1 = 0x00410044, |
| .p0_mpdgctrl0 = 0x42480248, |
| .p0_mpdgctrl1 = 0x023C023C, |
| .p0_mprddlctl = 0x40424644, |
| .p0_mpwrdlctl = 0x34323034, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6dl_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x0043004B, |
| .p0_mpwldectrl1 = 0x003A003E, |
| .p1_mpwldectrl0 = 0x0047004F, |
| .p1_mpwldectrl1 = 0x004E0061, |
| .p0_mpdgctrl0 = 0x42500250, |
| .p0_mpdgctrl1 = 0x0238023C, |
| .p1_mpdgctrl0 = 0x42640264, |
| .p1_mpdgctrl1 = 0x02500258, |
| .p0_mprddlctl = 0x40424846, |
| .p1_mprddlctl = 0x46484842, |
| .p0_mpwrdlctl = 0x38382C30, |
| .p1_mpwrdlctl = 0x34343430, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr_2g = { |
| .mem_speed = 1600, |
| .density = 2, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 14, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1310, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr_4g = { |
| .mem_speed = 1600, |
| .density = 4, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 15, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1310, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| static void ccgr_init(void) |
| { |
| struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| |
| writel(0x00C03F3F, &ccm->CCGR0); |
| writel(0x0030FC03, &ccm->CCGR1); |
| writel(0x0FFFC000, &ccm->CCGR2); |
| writel(0x3FF00000, &ccm->CCGR3); |
| writel(0x00FFF300, &ccm->CCGR4); |
| writel(0x0F0000C3, &ccm->CCGR5); |
| writel(0x000003FF, &ccm->CCGR6); |
| } |
| |
| /* Define a minimal structure so that the part number can be read via SPL */ |
| struct mfgdata { |
| unsigned char tsize; |
| /* size of checksummed part in bytes */ |
| unsigned char ckcnt; |
| /* checksum corrected byte */ |
| unsigned char cksum; |
| /* decimal serial number, packed BCD */ |
| unsigned char serial[6]; |
| /* part number, right justified, ASCII */ |
| unsigned char pn[16]; |
| }; |
| |
| static void conv_ascii(unsigned char *dst, unsigned char *src, int len) |
| { |
| int remain = len; |
| unsigned char *sptr = src; |
| unsigned char *dptr = dst; |
| |
| while (remain) { |
| if (*sptr) { |
| *dptr = *sptr; |
| dptr++; |
| } |
| sptr++; |
| remain--; |
| } |
| *dptr = 0x0; |
| } |
| |
| #define CFG_MFG_ADDR_OFFSET (spi->size - SZ_16K) |
| static bool is_2gb(void) |
| { |
| struct spi_flash *spi; |
| int ret; |
| char buf[sizeof(struct mfgdata)]; |
| struct mfgdata *data = (struct mfgdata *)buf; |
| unsigned char outbuf[32]; |
| |
| spi = spi_flash_probe(CONFIG_ENV_SPI_BUS, |
| CONFIG_ENV_SPI_CS, |
| CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE); |
| ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata), |
| buf); |
| if (ret) |
| return false; |
| |
| /* Congatec Part Numbers 104 and 105 have 2GiB of RAM */ |
| conv_ascii(outbuf, data->pn, sizeof(data->pn)); |
| if (!memcmp(outbuf, "016104", 6) || !memcmp(outbuf, "016105", 6)) |
| return true; |
| else |
| return false; |
| } |
| |
| static void spl_dram_init(int width) |
| { |
| struct mx6_ddr_sysinfo sysinfo = { |
| /* width of data bus:0=16,1=32,2=64 */ |
| .dsize = width / 32, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, /* 32Gb per CS */ |
| /* single chip select */ |
| .ncs = 1, |
| .cs1_mirror = 0, |
| .rtt_wr = 2, |
| .rtt_nom = 2, |
| .walat = 0, |
| .ralat = 5, |
| .mif3_mode = 3, |
| .bi_on = 1, |
| .sde_to_rst = 0x0d, |
| .rst_to_cke = 0x20, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 7, /* 8 refresh commands per refresh cycle */ |
| }; |
| |
| if (is_cpu_type(MXC_CPU_MX6Q) && is_2gb()) { |
| mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs); |
| mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g); |
| return; |
| } |
| |
| if (is_mx6dq()) { |
| mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs); |
| mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g); |
| } else if (is_cpu_type(MXC_CPU_MX6SOLO)) { |
| sysinfo.walat = 1; |
| mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g); |
| } else if (is_cpu_type(MXC_CPU_MX6DL)) { |
| sysinfo.walat = 1; |
| mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g); |
| } |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| /* setup AIPS and disable watchdog */ |
| arch_cpu_init(); |
| |
| ccgr_init(); |
| gpr_init(); |
| |
| /* iomux and setup of i2c */ |
| board_early_init_f(); |
| |
| /* setup GP timer */ |
| timer_init(); |
| |
| /* UART clocks enabled and gd valid - init serial console */ |
| preloader_console_init(); |
| |
| /* Needed for malloc() to work in SPL prior to board_init_r() */ |
| spl_init(); |
| |
| /* DDR initialization */ |
| if (is_cpu_type(MXC_CPU_MX6SOLO)) |
| spl_dram_init(32); |
| else |
| spl_dram_init(64); |
| |
| /* Clear the BSS. */ |
| memset(__bss_start, 0, __bss_end - __bss_start); |
| |
| /* load/boot image from boot device */ |
| board_init_r(NULL, 0); |
| } |
| #endif |