blob: ce1cf97cf0858f9df9fd194b0154b97806bfbe25 [file] [log] [blame]
/*
* Copyright 2013-2015 Arcturus Networks, Inc.
* http://www.arcturusnetworks.com/products/ucp1020/
* based on include/configs/p1_p2_rdb_pc.h
* original copyright follows:
* Copyright 2009-2011 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* QorIQ uCP1020-xx boards configuration file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_FSL_ELBC
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
#if defined(CONFIG_TARTGET_UCP1020T1)
#define CONFIG_UCP1020_REV_1_3
#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
#define CONFIG_P1020
#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC3
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_ETHADDR 00:19:D3:FF:FF:FF
#define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE
#define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD
#define CONFIG_IPADDR 10.80.41.229
#define CONFIG_SERVERIP 10.80.41.227
#define CONFIG_NETMASK 255.255.252.0
#define CONFIG_ETHPRIME "eTSEC3"
#ifndef CONFIG_SPI_FLASH
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_LAST_STAGE_INIT
#endif
#if defined(CONFIG_TARGET_UCP1020)
#define CONFIG_UCP1020
#define CONFIG_UCP1020_REV_1_3
#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
#define CONFIG_P1020
#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC2
#define CONFIG_TSEC3
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_ETHADDR 00:06:3B:FF:FF:FF
#define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE
#define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD
#define CONFIG_IPADDR 192.168.1.81
#define CONFIG_IPADDR1 192.168.1.82
#define CONFIG_IPADDR2 192.168.1.83
#define CONFIG_SERVERIP 192.168.1.80
#define CONFIG_GATEWAYIP 102.168.1.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_ETHPRIME "eTSEC1"
#ifndef CONFIG_SPI_FLASH
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE (256 << 10)
#define CONFIG_LAST_STAGE_INIT
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff80000
#endif
#define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500
/* #define CONFIG_MPC85xx */
#define CONFIG_MP
#define CONFIG_FSL_LAW
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CMD_SATA
#define CONFIG_SATA_SIL
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_SYS_CLK_FREQ 66666666
#define CONFIG_DDR_CLK_FREQ 66666666
#define CONFIG_HWCONFIG
#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
/*
* ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
* there will be one entry in this array for each two (dummy) sensors in
* CONFIG_DTT_SENSORS.
*
* For uCP1020 module:
* - only one ADM1021/NCT72
* - i2c addr 0x41
* - conversion rate 0x02 = 0.25 conversions/second
* - ALERT output disabled
* - local temp sensor enabled, min set to 0 deg, max set to 85 deg
* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
*/
#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
0x02, 0, 1, 0, 85, 1, 0, 85} }
#define CONFIG_CMD_DTT
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE
#define CONFIG_BTB
#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
#define CONFIG_ENABLE_36BIT_PHYS
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
SPL code*/
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif
/* DDR Setup */
#define CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_FSL_DDR3
#ifndef CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#endif
#define CONFIG_SYS_SPD_BUS_NUM 1
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
/* Default settings for DDR3 */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f
#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000
#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600
#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608
#define CONFIG_SYS_DDR_SR_CNTR 0x00000000
#define CONFIG_SYS_DDR_RCW_1 0x00000000
#define CONFIG_SYS_DDR_RCW_2 0x00000000
#ifdef CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */
#else
#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */
#endif
#define CONFIG_SYS_DDR_CONTROL_2 0x04401050
#define CONFIG_SYS_DDR_TIMING_4 0x00220001
#define CONFIG_SYS_DDR_TIMING_5 0x03402400
#define CONFIG_SYS_DDR_TIMING_3 0x00020000
#define CONFIG_SYS_DDR_TIMING_0 0x00330004
#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846
#define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF
#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000
#define CONFIG_SYS_DDR_MODE_1 0x40461520
#define CONFIG_SYS_DDR_MODE_2 0x8000c000
#define CONFIG_SYS_DDR_INTERVAL 0x0C300000
#undef CONFIG_CLOCKS_IN_MHZ
/*
* Memory map
*
* 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable
* 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2)
* 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1
* 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable
* (early boot only)
* 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable
* 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable
*/
/*
* Local Bus Definitions
*/
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
#define CONFIG_SYS_FLASH_BASE 0xec000000
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
| BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
/* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
/* Size of used area in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
#define CONFIG_SYS_PMC_BASE 0xff980000
#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE
#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
BR_PS_8 | BR_V)
#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
OR_GPCM_EAD)
#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
#ifdef CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#endif
/* Serial Port - controlled on board with jumper J8
* open - index 2
* shorted - index 1
*/
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_RTC_DS1337_NOOSC
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
#define CONFIG_SYS_I2C_IDT6V49205B 0x69
/*
* eSPI - Enhanced SPI
*/
#define CONFIG_HARD_SPI
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#if defined(CONFIG_PCI)
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9"
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_CMD_PCI
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */
/*
* Environment
*/
#ifdef CONFIG_ENV_FIT_UCBOOT
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#else
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_ENV_SPI_MODE 0
#ifdef CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x3000 /* 12KB */
#define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
#define CONFIG_ENV_SECT_SIZE 0x1000
#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#endif
#elif defined(CONFIG_RAMBOOT_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000)
#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#endif
#endif
#endif /* CONFIG_ENV_FIT_UCBOOT */
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
* Command line configuration.
*/
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_DATE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_CRAMFS
/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
#define CONFIG_USB_EHCI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#ifdef CONFIG_USB_EHCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_MMC_SPI
#define CONFIG_CMD_MMC_SPI
#define CONFIG_GENERIC_MMC
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
#define CONFIG_DOS_PARTITION
#endif
/* Misc Extra Settings */
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
/*
* For booting Linux, the board info and command line data
* have to be in the first 64 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#if defined(CONFIG_TSEC_ENET)
#if defined(CONFIG_UCP1020_REV_1_2)
#define CONFIG_PHY_MICREL_KSZ9021
#elif defined(CONFIG_UCP1020_REV_1_3)
#define CONFIG_PHY_MICREL_KSZ9031
#else
#error "UCP1020 module revision is not defined !!!"
#endif
#define CONFIG_BOOTP_SERVERIP
#define CONFIG_MII /* MII PHY management */
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_TSEC2_NAME "eTSEC2"
#define CONFIG_TSEC3_NAME "eTSEC3"
#define TSEC1_PHY_ADDR 4
#define TSEC2_PHY_ADDR 0
#define TSEC2_PHY_ADDR_SGMII 0x00
#define TSEC3_PHY_ADDR 6
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#endif
#define CONFIG_HOSTNAME UCP1020
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#if defined(CONFIG_DONGLE)
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run prog_spi_mbrbootcramfs\0" \
"bootfile=uImage\0" \
"consoledev=ttyS0\0" \
"cramfsfile=image.cramfs\0" \
"dtbaddr=0x00c00000\0" \
"dtbfile=image.dtb\0" \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
"fileaddr=0x01000000\0" \
"filesize=0x00080000\0" \
"flashmbr=sf probe 0; " \
"tftp $loadaddr $mbr; " \
"sf erase $mbr_offset +$filesize; " \
"sf write $loadaddr $mbr_offset $filesize\0" \
"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
"protect off $nor_recoveryaddr +$filesize; " \
"erase $nor_recoveryaddr +$filesize; " \
"cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
"protect on $nor_recoveryaddr +$filesize\0 " \
"flashuboot=tftp $ubootaddr $ubootfile; " \
"protect off $nor_ubootaddr +$filesize; " \
"erase $nor_ubootaddr +$filesize; " \
"cp.b $ubootaddr $nor_ubootaddr $filesize; " \
"protect on $nor_ubootaddr +$filesize\0 " \
"flashworking=tftp $workingaddr $cramfsfile; " \
"protect off $nor_workingaddr +$filesize; " \
"erase $nor_workingaddr +$filesize; " \
"cp.b $workingaddr $nor_workingaddr $filesize; " \
"protect on $nor_workingaddr +$filesize\0 " \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
"kerneladdr=0x01100000\0" \
"kernelfile=uImage\0" \
"loadaddr=0x01000000\0" \
"mbr=uCP1020d.mbr\0" \
"mbr_offset=0x00000000\0" \
"mmbr=uCP1020Quiet.mbr\0" \
"mmcpart=0:2\0" \
"mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
"mmc erase 1 1; " \
"mmc write $loadaddr 1 1\0" \
"mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \
"mmc erase 0x40 0x400; " \
"mmc write $loadaddr 0x40 0x400\0" \
"netdev=eth0\0" \
"nor_recoveryaddr=0xEC0A0000\0" \
"nor_ubootaddr=0xEFF80000\0" \
"nor_workingaddr=0xECFA0000\0" \
"norbootrecovery=setenv bootargs $recoverybootargs" \
" console=$consoledev,$baudrate $othbootargs; " \
"run norloadrecovery; " \
"bootm $kerneladdr - $dtbaddr\0" \
"norbootworking=setenv bootargs $workingbootargs" \
" console=$consoledev,$baudrate $othbootargs; " \
"run norloadworking; " \
"bootm $kerneladdr - $dtbaddr\0" \
"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
"setenv cramfsaddr $nor_recoveryaddr; " \
"cramfsload $dtbaddr $dtbfile; " \
"cramfsload $kerneladdr $kernelfile\0" \
"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
"setenv cramfsaddr $nor_workingaddr; " \
"cramfsload $dtbaddr $dtbfile; " \
"cramfsload $kerneladdr $kernelfile\0" \
"prog_spi_mbr=run spi__mbr\0" \
"prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \
"prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
"run spi__cramfs\0" \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
" console=$consoledev,$baudrate $othbootargs; " \
"tftp $rootfsaddr $rootfsfile; " \
"tftp $loadaddr $kernelfile; " \
"tftp $dtbaddr $dtbfile; " \
"bootm $loadaddr $rootfsaddr $dtbaddr\0" \
"ramdisk_size=120000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
"recoveryaddr=0x02F00000\0" \
"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
"mw.l 0xffe0f008 0x00400000\0" \
"rootfsaddr=0x02F00000\0" \
"rootfsfile=rootfs.ext2.gz.uboot\0" \
"rootpath=/opt/nfsroot\0" \
"spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
"protect off 0xeC000000 +$filesize; " \
"erase 0xEC000000 +$filesize; " \
"cp.b $loadaddr 0xEC000000 $filesize; " \
"cmp.b $loadaddr 0xEC000000 $filesize; " \
"protect on 0xeC000000 +$filesize\0" \
"spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
"protect off 0xeFF80000 +$filesize; " \
"erase 0xEFF80000 +$filesize; " \
"cp.b $loadaddr 0xEFF80000 $filesize; " \
"cmp.b $loadaddr 0xEFF80000 $filesize; " \
"protect on 0xeFF80000 +$filesize\0" \
"spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \
"sf probe 0; sf erase 0x8000 +$filesize; " \
"sf write $loadaddr 0x8000 $filesize\0" \
"spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \
"protect off 0xec0a0000 +$filesize; " \
"erase 0xeC0A0000 +$filesize; " \
"cp.b $loadaddr 0xeC0A0000 $filesize; " \
"protect on 0xec0a0000 +$filesize\0" \
"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
"sf probe 1; sf erase 0 +$filesize; " \
"sf write $loadaddr 0 $filesize\0" \
"spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \
"sf probe 0; sf erase 0 +$filesize; " \
"sf write $loadaddr 0 $filesize\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
"protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootaddr=0x01000000\0" \
"ubootfile=u-boot.bin\0" \
"ubootd=u-boot4dongle.bin\0" \
"upgrade=run flashworking\0" \
"usb_phy_type=ulpi\0 " \
"workingaddr=0x02F00000\0" \
"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
#else
#if defined(CONFIG_UCP1020T1)
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \
"bootfile=uImage\0" \
"consoledev=ttyS0\0" \
"cramfsfile=image.cramfs\0" \
"dtbaddr=0x00c00000\0" \
"dtbfile=image.dtb\0" \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
"fileaddr=0x01000000\0" \
"filesize=0x00080000\0" \
"flashmbr=sf probe 0; " \
"tftp $loadaddr $mbr; " \
"sf erase $mbr_offset +$filesize; " \
"sf write $loadaddr $mbr_offset $filesize\0" \
"flashrecovery=tftp $recoveryaddr $cramfsfile; " \
"protect off $nor_recoveryaddr +$filesize; " \
"erase $nor_recoveryaddr +$filesize; " \
"cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \
"protect on $nor_recoveryaddr +$filesize\0 " \
"flashuboot=tftp $ubootaddr $ubootfile; " \
"protect off $nor_ubootaddr +$filesize; " \
"erase $nor_ubootaddr +$filesize; " \
"cp.b $ubootaddr $nor_ubootaddr $filesize; " \
"protect on $nor_ubootaddr +$filesize\0 " \
"flashworking=tftp $workingaddr $cramfsfile; " \
"protect off $nor_workingaddr +$filesize; " \
"erase $nor_workingaddr +$filesize; " \
"cp.b $workingaddr $nor_workingaddr $filesize; " \
"protect on $nor_workingaddr +$filesize\0 " \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
"kerneladdr=0x01100000\0" \
"kernelfile=uImage\0" \
"loadaddr=0x01000000\0" \
"mbr=uCP1020.mbr\0" \
"mbr_offset=0x00000000\0" \
"netdev=eth0\0" \
"nor_recoveryaddr=0xEC0A0000\0" \
"nor_ubootaddr=0xEFF80000\0" \
"nor_workingaddr=0xECFA0000\0" \
"norbootrecovery=setenv bootargs $recoverybootargs" \
" console=$consoledev,$baudrate $othbootargs; " \
"run norloadrecovery; " \
"bootm $kerneladdr - $dtbaddr\0" \
"norbootworking=setenv bootargs $workingbootargs" \
" console=$consoledev,$baudrate $othbootargs; " \
"run norloadworking; " \
"bootm $kerneladdr - $dtbaddr\0" \
"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \
"setenv cramfsaddr $nor_recoveryaddr; " \
"cramfsload $dtbaddr $dtbfile; " \
"cramfsload $kerneladdr $kernelfile\0" \
"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \
"setenv cramfsaddr $nor_workingaddr; " \
"cramfsload $dtbaddr $dtbfile; " \
"cramfsload $kerneladdr $kernelfile\0" \
"othbootargs=quiet\0" \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
" console=$consoledev,$baudrate $othbootargs; " \
"tftp $rootfsaddr $rootfsfile; " \
"tftp $loadaddr $kernelfile; " \
"tftp $dtbaddr $dtbfile; " \
"bootm $loadaddr $rootfsaddr $dtbaddr\0" \
"ramdisk_size=120000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
"recoveryaddr=0x02F00000\0" \
"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
"mw.l 0xffe0f008 0x00400000\0" \
"rootfsaddr=0x02F00000\0" \
"rootfsfile=rootfs.ext2.gz.uboot\0" \
"rootpath=/opt/nfsroot\0" \
"silent=1\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
"protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootaddr=0x01000000\0" \
"ubootfile=u-boot.bin\0" \
"upgrade=run flashworking\0" \
"workingaddr=0x02F00000\0" \
"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"
#else /* For Arcturus Modules */
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootcmd=run norkernel\0" \
"bootfile=uImage\0" \
"consoledev=ttyS0\0" \
"dtbaddr=0x00c00000\0" \
"dtbfile=image.dtb\0" \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \
"fileaddr=0x01000000\0" \
"filesize=0x00080000\0" \
"flashmbr=sf probe 0; " \
"tftp $loadaddr $mbr; " \
"sf erase $mbr_offset +$filesize; " \
"sf write $loadaddr $mbr_offset $filesize\0" \
"flashuboot=tftp $loadaddr $ubootfile; " \
"protect off $nor_ubootaddr0 +$filesize; " \
"erase $nor_ubootaddr0 +$filesize; " \
"cp.b $loadaddr $nor_ubootaddr0 $filesize; " \
"protect on $nor_ubootaddr0 +$filesize; " \
"protect off $nor_ubootaddr1 +$filesize; " \
"erase $nor_ubootaddr1 +$filesize; " \
"cp.b $loadaddr $nor_ubootaddr1 $filesize; " \
"protect on $nor_ubootaddr1 +$filesize\0 " \
"format0=protect off $part0base +$part0size; " \
"erase $part0base +$part0size\0" \
"format1=protect off $part1base +$part1size; " \
"erase $part1base +$part1size\0" \
"format2=protect off $part2base +$part2size; " \
"erase $part2base +$part2size\0" \
"format3=protect off $part3base +$part3size; " \
"erase $part3base +$part3size\0" \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \
"kerneladdr=0x01100000\0" \
"kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \
"kernelfile=uImage\0" \
"loadaddr=0x01000000\0" \
"mbr=uCP1020.mbr\0" \
"mbr_offset=0x00000000\0" \
"netdev=eth0\0" \
"nor_ubootaddr0=0xEC000000\0" \
"nor_ubootaddr1=0xEFF80000\0" \
"norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
"run norkernelload; " \
"bootm $kerneladdr - $dtbaddr\0" \
"norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \
"setenv cramfsaddr $part0base; " \
"cramfsload $dtbaddr $dtbfile; " \
"cramfsload $kerneladdr $kernelfile\0" \
"part0base=0xEC100000\0" \
"part0size=0x00700000\0" \
"part1base=0xEC800000\0" \
"part1size=0x02000000\0" \
"part2base=0xEE800000\0" \
"part2size=0x00800000\0" \
"part3base=0xEF000000\0" \
"part3size=0x00F80000\0" \
"partENVbase=0xEC080000\0" \
"partENVsize=0x00080000\0" \
"program0=tftp part0-000000.bin; " \
"protect off $part0base +$filesize; " \
"erase $part0base +$filesize; " \
"cp.b $loadaddr $part0base $filesize; " \
"echo Verifying...; " \
"cmp.b $loadaddr $part0base $filesize\0" \
"program1=tftp part1-000000.bin; " \
"protect off $part1base +$filesize; " \
"erase $part1base +$filesize; " \
"cp.b $loadaddr $part1base $filesize; " \
"echo Verifying...; " \
"cmp.b $loadaddr $part1base $filesize\0" \
"program2=tftp part2-000000.bin; " \
"protect off $part2base +$filesize; " \
"erase $part2base +$filesize; " \
"cp.b $loadaddr $part2base $filesize; " \
"echo Verifying...; " \
"cmp.b $loadaddr $part2base $filesize\0" \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \
" console=$consoledev,$baudrate $othbootargs; " \
"tftp $rootfsaddr $rootfsfile; " \
"tftp $loadaddr $kernelfile; " \
"tftp $dtbaddr $dtbfile; " \
"bootm $loadaddr $rootfsaddr $dtbaddr\0" \
"ramdisk_size=120000\0" \
"ramdiskfile=rootfs.ext2.gz.uboot\0" \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \
"mw.l 0xffe0f008 0x00400000\0" \
"rootfsaddr=0x02F00000\0" \
"rootfsfile=rootfs.ext2.gz.uboot\0" \
"rootpath=/opt/nfsroot\0" \
"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \
"sf probe 0; sf erase 0 +$filesize; " \
"sf write $loadaddr 0 $filesize\0" \
"spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \
"protect off 0xeC000000 +$filesize; " \
"erase 0xEC000000 +$filesize; " \
"cp.b $loadaddr 0xEC000000 $filesize; " \
"cmp.b $loadaddr 0xEC000000 $filesize; " \
"protect on 0xeC000000 +$filesize\0" \
"tftpflash=tftpboot $loadaddr $uboot; " \
"protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
"protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootfile=u-boot.bin\0" \
"upgrade=run flashuboot\0" \
"usb_phy_type=ulpi\0 " \
"boot_nfs= " \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr\0" \
"boot_hd = " \
"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
"console=$consoledev,$baudrate $othbootargs;" \
"usb start;" \
"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
"bootm $loadaddr - $fdtaddr\0" \
"boot_usb_fat = " \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"ramdisk_size=$ramdisk_size;" \
"usb start;" \
"fatload usb 0:2 $loadaddr $bootfile;" \
"fatload usb 0:2 $fdtaddr $fdtfile;" \
"fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
"boot_usb_ext2 = " \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"ramdisk_size=$ramdisk_size;" \
"usb start;" \
"ext2load usb 0:4 $loadaddr $bootfile;" \
"ext2load usb 0:4 $fdtaddr $fdtfile;" \
"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \
"boot_nor = " \
"setenv bootargs root=/dev/$jffs2nor rw " \
"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
"bootm $norbootaddr - $norfdtaddr\0 " \
"boot_ram = " \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"ramdisk_size=$ramdisk_size;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr $fdtaddr\0"
#endif
#endif
#endif /* __CONFIG_H */