| /* |
| * (C) Copyright 2003 Embedded Edge, LLC |
| * Dan Malek <dan@embeddededge.com> |
| * Copied from ADS85xx. |
| * Updates for Silicon Tx GP3 8560 board. |
| * |
| * (C) Copyright 2002,2003 Motorola,Inc. |
| * Xianghua Xiao <X.Xiao@motorola.com> |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* mpc8560ads board configuration file */ |
| /* please refer to doc/README.mpc85xx for more info */ |
| /* make sure you change the MAC address and other network params first, |
| * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ |
| #define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ |
| #define CONFIG_MPC8560 1 /* MPC8560 specific */ |
| #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ |
| |
| #undef CONFIG_PCI /* pci ethernet support */ |
| #define CONFIG_TSEC_ENET /* tsec ethernet support*/ |
| #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #undef CONFIG_DDR_ECC /* only for ECC DDR module */ |
| |
| #if defined(CONFIG_MPC85xx_REV1) |
| #define CONFIG_DDR_DLL /* possible DLL fix needed */ |
| #endif |
| |
| /* Using Localbus SDRAM to emulate flash before we can program the flash, |
| * normally you need a flash-boot image(u-boot.bin), if so undef this. |
| */ |
| #undef CONFIG_RAM_AS_FLASH |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ |
| |
| /* Blinkin' LEDs for Robert :-) |
| */ |
| #define CONFIG_SHOW_ACTIVITY 1 |
| |
| #if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */ |
| #define CONFIG_DDR_SETTING |
| #endif |
| |
| /* below can be toggled for performance analysis. otherwise use default */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #undef CONFIG_BTB /* toggle branch predition */ |
| #undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ |
| |
| #define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ |
| |
| #undef CFG_DRAM_TEST /* memory test, takes time */ |
| #define CFG_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CFG_MEMTEST_END 0x00400000 |
| |
| #if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ |
| defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ |
| defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC)) |
| #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." |
| #endif |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ |
| #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE |
| |
| /* GPPP supports up to 2G of DRAM. Allocate up to 1G until we get |
| * a chance to try it out. Actual size is always read from sdram eeprom. |
| */ |
| #define CFG_SDRAM_SIZE 1024 /* DDR is 1GB */ |
| |
| /* Localbus SDRAM is an option, not all boards have it. |
| */ |
| #if defined(CONFIG_RAM_AS_FLASH) |
| #define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ |
| #else |
| #define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ |
| #endif |
| #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ |
| |
| #if defined(CONFIG_RAM_AS_FLASH) |
| #define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ |
| #define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ |
| #else /* Boot from real Flash */ |
| #define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ |
| #define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ |
| #endif |
| |
| #define CFG_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ |
| #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CFG_MAX_FLASH_SECT 136 /* sectors per device */ |
| #undef CFG_FLASH_CHECKSUM |
| #define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| /* The configuration latch is Chip Select 1. |
| * It's an 8-bit latch in the upper 8 bits of the word. |
| */ |
| #define CFG_BR1_PRELIM 0xfc001801 /* 32-bit port */ |
| #define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ |
| #define CFG_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ |
| |
| #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) |
| #define CFG_RAMBOOT |
| #else |
| #undef CFG_RAMBOOT |
| #endif |
| |
| #ifdef CFG_RAMBOOT |
| #define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ |
| #else |
| #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #endif |
| #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ |
| #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ |
| |
| |
| #define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ |
| |
| #if defined(CONFIG_DDR_SETTING) |
| #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ |
| #define CFG_DDR_CS0_CONFIG 0x80000002 |
| #define CFG_DDR_TIMING_1 0x37344321 |
| #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/ |
| #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/ |
| #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ |
| #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/ |
| #endif |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* local bus definitions */ |
| #define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ |
| #define CFG_OR2_PRELIM 0xfc006901 |
| #define CFG_LBC_LCRR 0x00030004 /* local bus freq */ |
| #define CFG_LBC_LBCR 0x00000000 |
| #define CFG_LBC_LSRT 0x20000000 |
| #define CFG_LBC_MRTPR 0x20000000 |
| #define CFG_LBC_LSDMR_1 0x2861b723 |
| #define CFG_LBC_LSDMR_2 0x0861b723 |
| #define CFG_LBC_LSDMR_3 0x0861b723 |
| #define CFG_LBC_LSDMR_4 0x1861b723 |
| #define CFG_LBC_LSDMR_5 0x4061b723 |
| |
| #define CONFIG_L1_INIT_RAM |
| #define CFG_INIT_RAM_LOCK 1 |
| #define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ |
| #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ |
| |
| #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_ON_SCC /* define if console on SCC */ |
| #undef CONFIG_CONS_NONE /* define if console on something else */ |
| #define CONFIG_CONS_INDEX 2 /* which serial channel for console */ |
| |
| #define CONFIG_BAUDRATE 38400 |
| |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| |
| /* Use the HUSH parser */ |
| #define CFG_HUSH_PARSER |
| #ifdef CFG_HUSH_PARSER |
| #define CFG_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* I2C */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support*/ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| #if 0 |
| #define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */ |
| #else |
| /* I did the 'if 0' so we could keep the syntax above if ever needed. */ |
| #undef CFG_I2C_NOPROBES |
| #endif |
| |
| #define CFG_PCI_MEM_BASE 0xe0000000 |
| #define CFG_PCI_MEM_PHYS 0xe0000000 |
| #define CFG_PCI_MEM_SIZE 0x10000000 |
| |
| #if defined(CONFIG_PCI) /* PCI Ethernet card */ |
| #define CONFIG_NET_MULTI |
| #define CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| #if !defined(CONFIG_PCI_PNP) |
| #define PCI_ENET0_IOADDR 0xe0000000 |
| #define PCI_ENET0_MEMADDR 0xe0000000 |
| #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ |
| #endif |
| #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ |
| #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ |
| #if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */ |
| #define CFG_PCI_SUBSYS_DEVICEID 0x0003 |
| #else |
| #define CFG_PCI_SUBSYS_DEVICEID 0x0009 |
| #endif |
| #elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 8 /* PHY address */ |
| #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ |
| #define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ |
| #undef CONFIG_ETHER_NONE /* define if ether on something else */ |
| #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ |
| #if (CONFIG_ETHER_INDEX == 2) |
| /* |
| * - Rx-CLK is CLK13 |
| * - Tx-CLK is CLK14 |
| * - Select bus for bd/buffers |
| * - Full duplex |
| */ |
| #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) |
| #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) |
| #define CFG_CPMFCR_RAMTYPE 0 |
| #if 0 |
| #define CFG_FCC_PSMR (FCC_PSMR_FDE) |
| #else |
| #define CFG_FCC_PSMR 0 |
| #endif |
| #define FETH2_RST 0x01 |
| #elif (CONFIG_ETHER_INDEX == 3) |
| /* need more definitions here for FE3 */ |
| #define FETH3_RST 0x80 |
| #endif /* CONFIG_ETHER_INDEX */ |
| #define CONFIG_MII /* MII PHY management */ |
| #undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ |
| /* |
| * GPIO pins used for bit-banged MII communications |
| */ |
| #define MDIO_PORT 2 /* Port C */ |
| #define MDIO_ACTIVE (iop->pdir |= 0x00400000) |
| #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) |
| #define MDIO_READ ((iop->pdat & 0x00400000) != 0) |
| |
| #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ |
| else iop->pdat &= ~0x00400000 |
| |
| #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ |
| else iop->pdat &= ~0x00200000 |
| |
| #define MIIDELAY udelay(1) |
| #endif |
| |
| /* Environment */ |
| /* We use the top boot sector flash, so we have some 16K sectors for env |
| * But....functions don't seem smart enough yet. |
| */ |
| #ifndef CFG_RAMBOOT |
| #if defined(CONFIG_RAM_AS_FLASH) |
| #define CFG_ENV_IS_NOWHERE |
| #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000) |
| #define CFG_ENV_SIZE 0x2000 |
| #else |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000) |
| #define CFG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ |
| #endif |
| #define CFG_ENV_SIZE 0x2000 |
| #else |
| #define CFG_NO_FLASH 1 /* Flash is not usable now */ |
| #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) |
| #define CFG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" |
| #define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xff900000" |
| #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| #if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) |
| #if defined(CONFIG_PCI) |
| #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ |
| CFG_CMD_PING | CFG_CMD_I2C) & \ |
| ~(CFG_CMD_ENV | \ |
| CFG_CMD_LOADS )) |
| #elif defined(CONFIG_TSEC_ENET) |
| #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \ |
| CFG_CMD_MII | CFG_CMD_I2C ) & \ |
| ~(CFG_CMD_ENV)) |
| #elif defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \ |
| CFG_CMD_PING | CFG_CMD_I2C) & \ |
| ~(CFG_CMD_ENV)) |
| #endif |
| #else |
| #if defined(CONFIG_PCI) |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ |
| CFG_CMD_PING | CFG_CMD_I2C) |
| #elif defined(CONFIG_TSEC_ENET) |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ |
| CFG_CMD_MII | CFG_CMD_I2C) |
| #elif defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ |
| CFG_CMD_PING | CFG_CMD_I2C) |
| #endif |
| #endif |
| #include <cmd_confdefs.h> |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "GPPP=> " /* Monitor Command Prompt */ |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| #define CFG_LOAD_ADDR 0x1000000 /* default load address */ |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* Cache Configuration */ |
| #define CFG_DCACHE_SIZE 32768 |
| #define CFG_CACHELINE_SIZE 32 |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /*Note: change below for your network setting!!! */ |
| #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_ETHADDR 00:01:af:07:9b:8a |
| #define CONFIG_ETH1ADDR 00:01:af:07:9b:8b |
| #define CONFIG_ETH2ADDR 00:01:af:07:9b:8c |
| #endif |
| |
| #define CONFIG_SERVERIP 192.168.85.1 |
| #define CONFIG_IPADDR 192.168.85.60 |
| #define CONFIG_GATEWAYIP 192.168.85.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_HOSTNAME STX_GP3 |
| #define CONFIG_ROOTPATH /gppproot |
| #define CONFIG_BOOTFILE uImage |
| |
| #endif /* __CONFIG_H */ |