blob: 829468fe7ed4dea0a8479c9b023840a9fb91b388 [file] [log] [blame]
/*
* U-boot - i386 Startup Code
*
* Copyright (c) 2002 Omicron Ceti AB, Daniel Engstr�m <denaiel@omicron.se>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <config.h>
#include <version.h>
#include <asm/global_data.h>
.section .text
.code32
.globl _start
.type _start, @function
.globl _i386boot_start
_i386boot_start:
/*
* This is the fail safe 32-bit bootstrap entry point. The
* following code is not executed from a cold-reset (actually, a
* lot of it is, but from real-mode after cold reset. It is
* repeated here to put the board into a state as close to cold
* reset as necessary)
*/
cli
cld
/* Turn of cache (this might require a 486-class CPU) */
movl %cr0, %eax
orl $0x60000000, %eax
movl %eax, %cr0
wbinvd
/* Tell 32-bit code it is being entered from an in-RAM copy */
movw $GD_FLG_WARM_BOOT, %bx
_start:
/* This is the 32-bit cold-reset entry point */
movl $0x18, %eax /* Load our segement registes, the
* gdt have already been loaded by start16.S */
movw %ax, %fs
movw %ax, %ds
movw %ax, %gs
movw %ax, %es
movw %ax, %ss
/* Clear the interupt vectors */
lidt blank_idt_ptr
/* Skip low-level initialization if not starting from cold-reset */
movl %ebx, %ecx
andl $GD_FLG_COLD_BOOT, %ecx
jz skip_mem_init
/* Early platform init (setup gpio, etc ) */
jmp early_board_init
.globl early_board_init_ret
early_board_init_ret:
/* size memory */
jmp mem_init
.globl mem_init_ret
mem_init_ret:
skip_mem_init:
/* fetch memory size (into %eax) */
jmp get_mem_size
.globl get_mem_size_ret
get_mem_size_ret:
#if CONFIG_SYS_SDRAM_ECC_ENABLE
/* Skip ECC initialization if not starting from cold-reset */
movl %ebx, %ecx
andl $GD_FLG_COLD_BOOT, %ecx
jz init_ecc_ret
jmp init_ecc
.globl init_ecc_ret
init_ecc_ret:
#endif
/* Check we have enough memory for stack */
movl $CONFIG_SYS_STACK_SIZE, %ecx
cmpl %ecx, %eax
jb die
mem_ok:
/* Set stack pointer to upper memory limit*/
movl %eax, %esp
/* Test the stack */
pushl $0
popl %ecx
cmpl $0, %ecx
jne die
push $0x55aa55aa
popl %ecx
cmpl $0x55aa55aa, %ecx
jne die
wbinvd
/* Determine our load offset */
call 1f
1: popl %ecx
subl $1b, %ecx
/* Set the upper memory limit parameter */
subl $CONFIG_SYS_STACK_SIZE, %eax
/* Reserve space for global data */
subl $(GD_SIZE * 4), %eax
/* %eax points to the global data structure */
movl %esp, (GD_RAM_SIZE * 4)(%eax)
movl %ebx, (GD_FLAGS * 4)(%eax)
movl %ecx, (GD_LOAD_OFF * 4)(%eax)
call board_init_f /* Enter, U-boot! */
/* indicate (lack of) progress */
movw $0x85, %ax
die: hlt
jmp die
hlt
blank_idt_ptr:
.word 0 /* limit */
.long 0 /* base */