| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2011 OMICRON electronics GmbH |
| * |
| * based on drivers/mtd/nand/raw/nand_spl_load.c |
| * |
| * Copyright (C) 2011 |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| */ |
| |
| #include <common.h> |
| #include <image.h> |
| #include <log.h> |
| #include <spi.h> |
| #include <spi_flash.h> |
| #include <errno.h> |
| #include <spl.h> |
| #include <asm/global_data.h> |
| #include <dm/ofnode.h> |
| |
| #if CONFIG_IS_ENABLED(OS_BOOT) |
| /* |
| * Load the kernel, check for a valid header we can parse, and if found load |
| * the kernel and then device tree. |
| */ |
| static int spi_load_image_os(struct spl_image_info *spl_image, |
| struct spl_boot_device *bootdev, |
| struct spi_flash *flash, |
| struct image_header *header) |
| { |
| int err; |
| |
| /* Read for a header, parse or error out. */ |
| spi_flash_read(flash, CONFIG_SYS_SPI_KERNEL_OFFS, sizeof(*header), |
| (void *)header); |
| |
| if (image_get_magic(header) != IH_MAGIC) |
| return -1; |
| |
| err = spl_parse_image_header(spl_image, bootdev, header); |
| if (err) |
| return err; |
| |
| spi_flash_read(flash, CONFIG_SYS_SPI_KERNEL_OFFS, |
| spl_image->size, (void *)spl_image->load_addr); |
| |
| /* Read device tree. */ |
| spi_flash_read(flash, CONFIG_SYS_SPI_ARGS_OFFS, |
| CONFIG_SYS_SPI_ARGS_SIZE, |
| (void *)CONFIG_SYS_SPL_ARGS_ADDR); |
| |
| return 0; |
| } |
| #endif |
| |
| static ulong spl_spi_fit_read(struct spl_load_info *load, ulong sector, |
| ulong count, void *buf) |
| { |
| struct spi_flash *flash = load->dev; |
| ulong ret; |
| |
| ret = spi_flash_read(flash, sector, count, buf); |
| if (!ret) |
| return count; |
| else |
| return 0; |
| } |
| |
| unsigned int __weak spl_spi_get_uboot_offs(struct spi_flash *flash) |
| { |
| return CONFIG_SYS_SPI_U_BOOT_OFFS; |
| } |
| |
| u32 __weak spl_spi_boot_bus(void) |
| { |
| return CONFIG_SF_DEFAULT_BUS; |
| } |
| |
| u32 __weak spl_spi_boot_cs(void) |
| { |
| return CONFIG_SF_DEFAULT_CS; |
| } |
| |
| /* |
| * The main entry for SPI booting. It's necessary that SDRAM is already |
| * configured and available since this code loads the main U-Boot image |
| * from SPI into SDRAM and starts it from there. |
| */ |
| static int spl_spi_load_image(struct spl_image_info *spl_image, |
| struct spl_boot_device *bootdev) |
| { |
| int err = 0; |
| unsigned int payload_offs; |
| struct spi_flash *flash; |
| struct image_header *header; |
| unsigned int sf_bus = spl_spi_boot_bus(); |
| unsigned int sf_cs = spl_spi_boot_cs(); |
| |
| /* |
| * Load U-Boot image from SPI flash into RAM |
| * In DM mode: defaults speed and mode will be |
| * taken from DT when available |
| */ |
| flash = spi_flash_probe(sf_bus, sf_cs, |
| CONFIG_SF_DEFAULT_SPEED, |
| CONFIG_SF_DEFAULT_MODE); |
| if (!flash) { |
| puts("SPI probe failed.\n"); |
| return -ENODEV; |
| } |
| |
| payload_offs = spl_spi_get_uboot_offs(flash); |
| |
| header = spl_get_load_buffer(-sizeof(*header), sizeof(*header)); |
| |
| if (CONFIG_IS_ENABLED(OF_REAL)) { |
| payload_offs = ofnode_conf_read_int("u-boot,spl-payload-offset", |
| payload_offs); |
| } |
| |
| #if CONFIG_IS_ENABLED(OS_BOOT) |
| if (spl_start_uboot() || spi_load_image_os(spl_image, bootdev, flash, header)) |
| #endif |
| { |
| /* Load u-boot, mkimage header is 64 bytes. */ |
| err = spi_flash_read(flash, payload_offs, sizeof(*header), |
| (void *)header); |
| if (err) { |
| debug("%s: Failed to read from SPI flash (err=%d)\n", |
| __func__, err); |
| return err; |
| } |
| |
| if (IS_ENABLED(CONFIG_SPL_LOAD_FIT_FULL) && |
| image_get_magic(header) == FDT_MAGIC) { |
| err = spi_flash_read(flash, payload_offs, |
| roundup(fdt_totalsize(header), 4), |
| (void *)CONFIG_SYS_LOAD_ADDR); |
| if (err) |
| return err; |
| err = spl_parse_image_header(spl_image, bootdev, |
| (struct image_header *)CONFIG_SYS_LOAD_ADDR); |
| } else if (IS_ENABLED(CONFIG_SPL_LOAD_FIT) && |
| image_get_magic(header) == FDT_MAGIC) { |
| struct spl_load_info load; |
| |
| debug("Found FIT\n"); |
| load.dev = flash; |
| load.priv = NULL; |
| load.filename = NULL; |
| load.bl_len = 1; |
| load.read = spl_spi_fit_read; |
| err = spl_load_simple_fit(spl_image, &load, |
| payload_offs, |
| header); |
| } else if (IS_ENABLED(CONFIG_SPL_LOAD_IMX_CONTAINER)) { |
| struct spl_load_info load; |
| |
| load.dev = flash; |
| load.priv = NULL; |
| load.filename = NULL; |
| load.bl_len = 1; |
| load.read = spl_spi_fit_read; |
| |
| err = spl_load_imx_container(spl_image, &load, |
| payload_offs); |
| } else { |
| err = spl_parse_image_header(spl_image, bootdev, header); |
| if (err) |
| return err; |
| err = spi_flash_read(flash, payload_offs + spl_image->offset, |
| spl_image->size, |
| (void *)spl_image->load_addr); |
| } |
| if (IS_ENABLED(CONFIG_SPI_FLASH_SOFT_RESET)) { |
| err = spi_nor_remove(flash); |
| if (err) |
| return err; |
| } |
| } |
| |
| return err; |
| } |
| /* Use priorty 1 so that boards can override this */ |
| SPL_LOAD_IMAGE_METHOD("SPI", 1, BOOT_DEVICE_SPI, spl_spi_load_image); |