arch/arm/dts/ebisu.dtsi - platform/external/u-boot - Gitiles

 // SPDX-License-Identifier: GPL-2.0
 /*
  * Device Tree Source for the Ebisu board
  *
  * Copyright (C) 2018 Renesas Electronics Corp.
  */

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>

 / {
 	model = "Renesas Ebisu board";
 	compatible = "renesas,ebisu";

 	aliases {
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		i2c2 = &i2c2;
 		i2c3 = &i2c3;
 		i2c4 = &i2c4;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
 		i2c7 = &i2c7;
 		serial0 = &scif2;
 		ethernet0 = &avb;
 		mmc0 = &sdhi3;
 		mmc1 = &sdhi0;
 		mmc2 = &sdhi1;
 	};

 	chosen {
 		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
 		stdout-path = "serial0:115200n8";
 	};

 	audio_clkout: audio-clkout {
 		/*
 		 * This is same as <&rcar_sound 0>
 		 * but needed to avoid cs2000/rcar_sound probe dead-lock
 		 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <11289600>;
 	};

 	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm3 0 50000>;

 		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
 		default-brightness-level = <10>;

 		power-supply = <&reg_12p0v>;
 	};

 	cvbs-in {
 		compatible = "composite-video-connector";
 		label = "CVBS IN";

 		port {
 			cvbs_con: endpoint {
 				remote-endpoint = <&adv7482_ain7>;
 			};
 		};
 	};

 	hdmi-in {
 		compatible = "hdmi-connector";
 		label = "HDMI IN";
 		type = "a";

 		port {
 			hdmi_in_con: endpoint {
 				remote-endpoint = <&adv7482_hdmi>;
 			};
 		};
 	};

 	hdmi-out {
 		compatible = "hdmi-connector";
 		type = "a";

 		port {
 			hdmi_con_out: endpoint {
 				remote-endpoint = <&adv7511_out>;
 			};
 		};
 	};

 	keys {
 		compatible = "gpio-keys";

 		pinctrl-0 = <&keys_pins>;
 		pinctrl-names = "default";

 		key-1 {
 			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_1>;
 			label = "SW4-1";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-2 {
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_2>;
 			label = "SW4-2";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-3 {
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_3>;
 			label = "SW4-3";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-4 {
 			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_4>;
 			label = "SW4-4";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 	};

 	lvds-decoder {
 		compatible = "thine,thc63lvd1024";
 		vcc-supply = <&reg_3p3v>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				thc63lvd1024_in: endpoint {
 					remote-endpoint = <&lvds0_out>;
 				};
 			};

 			port@2 {
 				reg = <2>;
 				thc63lvd1024_out: endpoint {
 					remote-endpoint = <&adv7511_in>;
 				};
 			};
 		};
 	};

 	memory@48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
 		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};

 	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	reg_12p0v: regulator-12p0v {
 		compatible = "regulator-fixed";
 		regulator-name = "D12.0V";
 		regulator-min-microvolt = <12000000>;
 		regulator-max-microvolt = <12000000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	rsnd_ak4613: sound {
 		compatible = "simple-audio-card";

 		simple-audio-card,name = "rsnd-ak4613";
 		simple-audio-card,format = "left_j";
 		simple-audio-card,bitclock-master = <&sndcpu>;
 		simple-audio-card,frame-master = <&sndcpu>;

 		sndcodec: simple-audio-card,codec {
 			sound-dai = <&ak4613>;
 		};

 		sndcpu: simple-audio-card,cpu {
 			sound-dai = <&rcar_sound>;
 		};
 	};

 	vbus0_usb2: regulator-vbus0-usb2 {
 		compatible = "regulator-fixed";

 		regulator-name = "USB20_VBUS_CN";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;

 		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};

 	vcc_sdhi0: regulator-vcc-sdhi0 {
 		compatible = "regulator-fixed";

 		regulator-name = "SDHI0 Vcc";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;

 		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};

 	vccq_sdhi0: regulator-vccq-sdhi0 {
 		compatible = "regulator-gpio";

 		regulator-name = "SDHI0 VccQ";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;

 		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
 		states = <3300000 1>, <1800000 0>;
 	};

 	vcc_sdhi1: regulator-vcc-sdhi1 {
 		compatible = "regulator-fixed";

 		regulator-name = "SDHI1 Vcc";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;

 		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};

 	vccq_sdhi1: regulator-vccq-sdhi1 {
 		compatible = "regulator-gpio";

 		regulator-name = "SDHI1 VccQ";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;

 		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
 		states = <3300000 1>, <1800000 0>;
 	};

 	vga {
 		compatible = "vga-connector";

 		port {
 			vga_in: endpoint {
 				remote-endpoint = <&adv7123_out>;
 			};
 		};
 	};

 	vga-encoder {
 		compatible = "adi,adv7123";

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				adv7123_in: endpoint {
 					remote-endpoint = <&du_out_rgb>;
 				};
 			};
 			port@1 {
 				reg = <1>;
 				adv7123_out: endpoint {
 					remote-endpoint = <&vga_in>;
 				};
 			};
 		};
 	};

 	x12_clk: x12 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24576000>;
 	};

 	x13_clk: x13 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <74250000>;
 	};
 };

 &audio_clk_a {
 	clock-frequency = <22579200>;
 };

 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
 	phy-handle = <&phy0>;
 	status = "okay";

 	phy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-id0022.1622",
 			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 		/*
 		 * TX clock internal delay mode is required for reliable
 		 * 1Gbps communication using the KSZ9031RNX phy present on
 		 * the Ebisu board, however, TX clock internal delay mode
 		 * isn't supported on R-Car E3(e).  Thus, limit speed to
 		 * 100Mbps for reliable communication.
 		 */
 		max-speed = <100>;
 	};
 };

 &canfd {
 	pinctrl-0 = <&canfd0_pins>;
 	pinctrl-names = "default";
 	status = "okay";

 	channel0 {
 		status = "okay";
 	};
 };

 &csi40 {
 	status = "okay";

 	ports {
 		port@0 {
 			csi40_in: endpoint {
 				clock-lanes = <0>;
 				data-lanes = <1 2>;
 				remote-endpoint = <&adv7482_txa>;
 			};
 		};
 	};
 };

 &du {
 	pinctrl-0 = <&du_pins>;
 	pinctrl-names = "default";
 	status = "okay";

 	clocks = <&cpg CPG_MOD 724>,
 		 <&cpg CPG_MOD 723>,
 		 <&x13_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0";

 	ports {
 		port@0 {
 			du_out_rgb: endpoint {
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
 	};
 };

 &ehci0 {
 	dr_mode = "otg";
 	status = "okay";
 };

 &extal_clk {
 	clock-frequency = <48000000>;
 };

 &hsusb {
 	dr_mode = "otg";
 	status = "okay";
 };

 &i2c0 {
 	status = "okay";

 	io_expander: gpio@20 {
 		compatible = "onnn,pca9654";
 		reg = <0x20>;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
 	};

 	hdmi-encoder@39 {
 		compatible = "adi,adv7511w";
 		reg = <0x39>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;

 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				adv7511_in: endpoint {
 					remote-endpoint = <&thc63lvd1024_out>;
 				};
 			};

 			port@1 {
 				reg = <1>;
 				adv7511_out: endpoint {
 					remote-endpoint = <&hdmi_con_out>;
 				};
 			};
 		};
 	};

 	video-receiver@70 {
 		compatible = "adi,adv7482";
 		reg = <0x70>;

 		interrupt-parent = <&gpio0>;
 		interrupt-names = "intrq1", "intrq2";
 		interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
 			     <17 IRQ_TYPE_LEVEL_LOW>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@7 {
 				reg = <7>;

 				adv7482_ain7: endpoint {
 					remote-endpoint = <&cvbs_con>;
 				};
 			};

 			port@8 {
 				reg = <8>;

 				adv7482_hdmi: endpoint {
 					remote-endpoint = <&hdmi_in_con>;
 				};
 			};

 			port@a {
 				reg = <10>;

 				adv7482_txa: endpoint {
 					clock-lanes = <0>;
 					data-lanes = <1 2>;
 					remote-endpoint = <&csi40_in>;
 				};
 			};
 		};
 	};
 };

 &i2c3 {
 	status = "okay";

 	ak4613: codec@10 {
 		compatible = "asahi-kasei,ak4613";
 		#sound-dai-cells = <0>;
 		reg = <0x10>;
 		clocks = <&rcar_sound 3>;

 		asahi-kasei,in1-single-end;
 		asahi-kasei,in2-single-end;
 		asahi-kasei,out1-single-end;
 		asahi-kasei,out2-single-end;
 		asahi-kasei,out3-single-end;
 		asahi-kasei,out4-single-end;
 		asahi-kasei,out5-single-end;
 		asahi-kasei,out6-single-end;
 	};

 	cs2000: clk-multiplier@4f {
 		#clock-cells = <0>;
 		compatible = "cirrus,cs2000-cp";
 		reg = <0x4f>;
 		clocks = <&audio_clkout>, <&x12_clk>;
 		clock-names = "clk_in", "ref_clk";

 		assigned-clocks = <&cs2000>;
 		assigned-clock-rates = <24576000>; /* 1/1 divide */
 	};
 };

 &i2c_dvfs {
 	status = "okay";

 	clock-frequency = <400000>;

 	pmic: pmic@30 {
 		pinctrl-0 = <&irq0_pins>;
 		pinctrl-names = "default";

 		compatible = "rohm,bd9571mwv";
 		reg = <0x30>;
 		interrupt-parent = <&intc_ex>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		gpio-controller;
 		#gpio-cells = <2>;
 		rohm,ddr-backup-power = <0x1>;
 		rohm,rstbmode-level;
 	};

 	eeprom@50 {
 		compatible = "rohm,br24t01", "atmel,24c01";
 		reg = <0x50>;
 		pagesize = <8>;
 	};
 };

 &lvds0 {
 	status = "okay";

 	clocks = <&cpg CPG_MOD 727>,
 		 <&x13_clk>,
 		 <&extal_clk>;
 	clock-names = "fck", "dclkin.0", "extal";

 	ports {
 		port@1 {
 			lvds0_out: endpoint {
 				remote-endpoint = <&thc63lvd1024_in>;
 			};
 		};
 	};
 };

 &lvds1 {
 	/*
 	 * Even though the LVDS1 output is not connected, the encoder must be
 	 * enabled to supply a pixel clock to the DU for the DPAD output when
 	 * LVDS0 is in use.
 	 */
 	status = "okay";

 	clocks = <&cpg CPG_MOD 727>,
 		 <&x13_clk>,
 		 <&extal_clk>;
 	clock-names = "fck", "dclkin.0", "extal";
 };

 &ohci0 {
 	dr_mode = "otg";
 	status = "okay";
 };

 &pcie_bus_clk {
 	clock-frequency = <100000000>;
 };

 &pciec0 {
 	status = "okay";
 };

 &pfc {
 	avb_pins: avb {
 		groups = "avb_link", "avb_mii";
 		function = "avb";
 	};

 	canfd0_pins: canfd0 {
 		groups = "canfd0_data";
 		function = "canfd0";
 	};

 	du_pins: du {
 		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
 		function = "du";
 	};

 	irq0_pins: irq0 {
 		groups = "intc_ex_irq0";
 		function = "intc_ex";
 	};

 	keys_pins: keys {
 		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
 		bias-pull-up;
 	};

 	pwm3_pins: pwm3 {
 		groups = "pwm3_b";
 		function = "pwm3";
 	};

 	pwm5_pins: pwm5 {
 		groups = "pwm5_a";
 		function = "pwm5";
 	};

 	rpc_pins: rpc {
 		groups = "rpc_clk2", "rpc_ctrl", "rpc_data", "rpc_reset",
 			 "rpc_int";
 		function = "rpc";
 	};

 	scif2_pins: scif2 {
 		groups = "scif2_data_a";
 		function = "scif2";
 	};

 	sdhi0_pins: sd0 {
 		groups = "sdhi0_data4", "sdhi0_ctrl";
 		function = "sdhi0";
 		power-source = <3300>;
 	};

 	sdhi0_pins_uhs: sd0_uhs {
 		groups = "sdhi0_data4", "sdhi0_ctrl";
 		function = "sdhi0";
 		power-source = <1800>;
 	};

 	sdhi1_pins: sd1 {
 		groups = "sdhi1_data4", "sdhi1_ctrl";
 		function = "sdhi1";
 		power-source = <3300>;
 	};

 	sdhi1_pins_uhs: sd1_uhs {
 		groups = "sdhi1_data4", "sdhi1_ctrl";
 		function = "sdhi1";
 		power-source = <1800>;
 	};

 	sdhi3_pins: sd3 {
 		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
 		function = "sdhi3";
 		power-source = <1800>;
 	};

 	sound_clk_pins: sound_clk {
 		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
 			 "audio_clkout_a", "audio_clkout1_a";
 		function = "audio_clk";
 	};

 	sound_pins: sound {
 		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
 		function = "ssi";
 	};

 	usb0_pins: usb {
 		groups = "usb0_b", "usb0_id";
 		function = "usb0";
 	};

 	usb30_pins: usb30 {
 		groups = "usb30";
 		function = "usb30";
 	};
 };

 &pwm3 {
 	pinctrl-0 = <&pwm3_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &pwm5 {
 	pinctrl-0 = <&pwm5_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &rcar_sound {
 	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
 	pinctrl-names = "default";

 	/* Single DAI */
 	#sound-dai-cells = <0>;

 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
 	clock-frequency = <12288000 11289600>;

 	status = "okay";

 	/* update <audio_clk_b> to <cs2000> */
 	clocks = <&cpg CPG_MOD 1005>,
 		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
 		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
 		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
 		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
 		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
 		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
 		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
 		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
 		 <&cpg CPG_CORE R8A77990_CLK_ZA2>;

 	rcar_sound,dai {
 		dai0 {
 			playback = <&ssi0>, <&src0>, <&dvc0>;
 			capture = <&ssi1>, <&src1>, <&dvc1>;
 		};
 	};

 };

 &rpc {
 	pinctrl-0 = <&rpc_pins>;
 	pinctrl-names = "default";

 	/* Left disabled.  To be enabled by firmware when unlocked. */

 	flash@0 {
 		compatible = "cypress,hyperflash", "cfi-flash";
 		reg = <0>;

 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;

 			bootparam@0 {
 				reg = <0x00000000 0x040000>;
 				read-only;
 			};
 			bl2@40000 {
 				reg = <0x00040000 0x140000>;
 				read-only;
 			};
 			cert_header_sa6@180000 {
 				reg = <0x00180000 0x040000>;
 				read-only;
 			};
 			bl31@1c0000 {
 				reg = <0x001c0000 0x040000>;
 				read-only;
 			};
 			tee@200000 {
 				reg = <0x00200000 0x440000>;
 				read-only;
 			};
 			uboot@640000 {
 				reg = <0x00640000 0x100000>;
 				read-only;
 			};
 			dtb@740000 {
 				reg = <0x00740000 0x080000>;
 			};
 			kernel@7c0000 {
 				reg = <0x007c0000 0x1400000>;
 			};
 			user@1bc0000 {
 				reg = <0x01bc0000 0x2440000>;
 			};
 		};
 	};
 };

 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
 };

 &scif2 {
 	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
 	pinctrl-1 = <&sdhi0_pins_uhs>;
 	pinctrl-names = "default", "state_uhs";

 	vmmc-supply = <&vcc_sdhi0>;
 	vqmmc-supply = <&vccq_sdhi0>;
 	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 	bus-width = <4>;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	status = "okay";
 };

 &sdhi1 {
 	pinctrl-0 = <&sdhi1_pins>;
 	pinctrl-1 = <&sdhi1_pins_uhs>;
 	pinctrl-names = "default", "state_uhs";

 	vmmc-supply = <&vcc_sdhi1>;
 	vqmmc-supply = <&vccq_sdhi1>;
 	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	status = "okay";
 };

 &sdhi3 {
 	/* used for on-board 8bit eMMC */
 	pinctrl-0 = <&sdhi3_pins>;
 	pinctrl-1 = <&sdhi3_pins>;
 	pinctrl-names = "default", "state_uhs";

 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	mmc-hs200-1_8v;
 	mmc-hs400-1_8v;
 	bus-width = <8>;
 	no-sd;
 	no-sdio;
 	non-removable;
 	full-pwr-cycle-in-suspend;
 	status = "okay";
 };

 &ssi1 {
 	shared-pin;
 };

 &usb2_phy0 {
 	pinctrl-0 = <&usb0_pins>;
 	pinctrl-names = "default";

 	vbus-supply = <&vbus0_usb2>;
 	status = "okay";
 };

 &usb3_peri0 {
 	companion = <&xhci0>;
 	status = "okay";
 };

 &vin4 {
 	status = "okay";
 };

 &vin5 {
 	status = "okay";
 };

 &xhci0 {
 	pinctrl-0 = <&usb30_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };
	// SPDX-License-Identifier: GPL-2.0
	/*
	* Device Tree Source for the Ebisu board
	*
	* Copyright (C) 2018 Renesas Electronics Corp.
	*/

	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>

	/ {
	model = "Renesas Ebisu board";
	compatible = "renesas,ebisu";

	aliases {
	i2c0 = &i2c0;
	i2c1 = &i2c1;
	i2c2 = &i2c2;
	i2c3 = &i2c3;
	i2c4 = &i2c4;
	i2c5 = &i2c5;
	i2c6 = &i2c6;
	i2c7 = &i2c7;
	serial0 = &scif2;
	ethernet0 = &avb;
	mmc0 = &sdhi3;
	mmc1 = &sdhi0;
	mmc2 = &sdhi1;
	};

	chosen {
	bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
	stdout-path = "serial0:115200n8";
	};

	audio_clkout: audio-clkout {
	/*
	* This is same as <&rcar_sound 0>
	* but needed to avoid cs2000/rcar_sound probe dead-lock
	*/
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <11289600>;
	};

	backlight: backlight {
	compatible = "pwm-backlight";
	pwms = <&pwm3 0 50000>;

	brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
	default-brightness-level = <10>;

	power-supply = <&reg_12p0v>;
	};

	cvbs-in {
	compatible = "composite-video-connector";
	label = "CVBS IN";

	port {
	cvbs_con: endpoint {
	remote-endpoint = <&adv7482_ain7>;
	};
	};
	};

	hdmi-in {
	compatible = "hdmi-connector";
	label = "HDMI IN";
	type = "a";

	port {
	hdmi_in_con: endpoint {
	remote-endpoint = <&adv7482_hdmi>;
	};
	};
	};

	hdmi-out {
	compatible = "hdmi-connector";
	type = "a";

	port {
	hdmi_con_out: endpoint {
	remote-endpoint = <&adv7511_out>;
	};
	};
	};

	keys {
	compatible = "gpio-keys";

	pinctrl-0 = <&keys_pins>;
	pinctrl-names = "default";

	key-1 {
	gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_1>;
	label = "SW4-1";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-2 {
	gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_2>;
	label = "SW4-2";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-3 {
	gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_3>;
	label = "SW4-3";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-4 {
	gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_4>;
	label = "SW4-4";
	wakeup-source;
	debounce-interval = <20>;
	};
	};

	lvds-decoder {
	compatible = "thine,thc63lvd1024";
	vcc-supply = <&reg_3p3v>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	thc63lvd1024_in: endpoint {
	remote-endpoint = <&lvds0_out>;
	};
	};

	port@2 {
	reg = <2>;
	thc63lvd1024_out: endpoint {
	remote-endpoint = <&adv7511_in>;
	};
	};
	};
	};

	memory@48000000 {
	device_type = "memory";
	/* first 128MB is reserved for secure area. */
	reg = <0x0 0x48000000 0x0 0x38000000>;
	};

	reg_1p8v: regulator-1p8v {
	compatible = "regulator-fixed";
	regulator-name = "fixed-1.8V";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-boot-on;
	regulator-always-on;
	};

	reg_3p3v: regulator-3p3v {
	compatible = "regulator-fixed";
	regulator-name = "fixed-3.3V";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-boot-on;
	regulator-always-on;
	};

	reg_12p0v: regulator-12p0v {
	compatible = "regulator-fixed";
	regulator-name = "D12.0V";
	regulator-min-microvolt = <12000000>;
	regulator-max-microvolt = <12000000>;
	regulator-boot-on;
	regulator-always-on;
	};

	rsnd_ak4613: sound {
	compatible = "simple-audio-card";

	simple-audio-card,name = "rsnd-ak4613";
	simple-audio-card,format = "left_j";
	simple-audio-card,bitclock-master = <&sndcpu>;
	simple-audio-card,frame-master = <&sndcpu>;

	sndcodec: simple-audio-card,codec {
	sound-dai = <&ak4613>;
	};

	sndcpu: simple-audio-card,cpu {
	sound-dai = <&rcar_sound>;
	};
	};

	vbus0_usb2: regulator-vbus0-usb2 {
	compatible = "regulator-fixed";

	regulator-name = "USB20_VBUS_CN";
	regulator-min-microvolt = <5000000>;
	regulator-max-microvolt = <5000000>;

	gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	};

	vcc_sdhi0: regulator-vcc-sdhi0 {
	compatible = "regulator-fixed";

	regulator-name = "SDHI0 Vcc";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;

	gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	};

	vccq_sdhi0: regulator-vccq-sdhi0 {
	compatible = "regulator-gpio";

	regulator-name = "SDHI0 VccQ";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <3300000>;

	gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
	gpios-states = <1>;
	states = <3300000 1>, <1800000 0>;
	};

	vcc_sdhi1: regulator-vcc-sdhi1 {
	compatible = "regulator-fixed";

	regulator-name = "SDHI1 Vcc";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;

	gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
	enable-active-high;
	};

	vccq_sdhi1: regulator-vccq-sdhi1 {
	compatible = "regulator-gpio";

	regulator-name = "SDHI1 VccQ";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <3300000>;

	gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
	gpios-states = <1>;
	states = <3300000 1>, <1800000 0>;
	};

	vga {
	compatible = "vga-connector";

	port {
	vga_in: endpoint {
	remote-endpoint = <&adv7123_out>;
	};
	};
	};

	vga-encoder {
	compatible = "adi,adv7123";

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	adv7123_in: endpoint {
	remote-endpoint = <&du_out_rgb>;
	};
	};
	port@1 {
	reg = <1>;
	adv7123_out: endpoint {
	remote-endpoint = <&vga_in>;
	};
	};
	};
	};

	x12_clk: x12 {
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <24576000>;
	};

	x13_clk: x13 {
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <74250000>;
	};
	};

	&audio_clk_a {
	clock-frequency = <22579200>;
	};

	&avb {
	pinctrl-0 = <&avb_pins>;
	pinctrl-names = "default";
	phy-handle = <&phy0>;
	status = "okay";

	phy0: ethernet-phy@0 {
	compatible = "ethernet-phy-id0022.1622",
	"ethernet-phy-ieee802.3-c22";
	rxc-skew-ps = <1500>;
	reg = <0>;
	interrupt-parent = <&gpio2>;
	interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
	reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
	/*
	* TX clock internal delay mode is required for reliable
	* 1Gbps communication using the KSZ9031RNX phy present on
	* the Ebisu board, however, TX clock internal delay mode
	* isn't supported on R-Car E3(e). Thus, limit speed to
	* 100Mbps for reliable communication.
	*/
	max-speed = <100>;
	};
	};

	&canfd {
	pinctrl-0 = <&canfd0_pins>;
	pinctrl-names = "default";
	status = "okay";

	channel0 {
	status = "okay";
	};
	};

	&csi40 {
	status = "okay";

	ports {
	port@0 {
	csi40_in: endpoint {
	clock-lanes = <0>;
	data-lanes = <1 2>;
	remote-endpoint = <&adv7482_txa>;
	};
	};
	};
	};

	&du {
	pinctrl-0 = <&du_pins>;
	pinctrl-names = "default";
	status = "okay";

	clocks = <&cpg CPG_MOD 724>,
	<&cpg CPG_MOD 723>,
	<&x13_clk>;
	clock-names = "du.0", "du.1", "dclkin.0";

	ports {
	port@0 {
	du_out_rgb: endpoint {
	remote-endpoint = <&adv7123_in>;
	};
	};
	};
	};

	&ehci0 {
	dr_mode = "otg";
	status = "okay";
	};

	&extal_clk {
	clock-frequency = <48000000>;
	};

	&hsusb {
	dr_mode = "otg";
	status = "okay";
	};

	&i2c0 {
	status = "okay";

	io_expander: gpio@20 {
	compatible = "onnn,pca9654";
	reg = <0x20>;
	gpio-controller;
	#gpio-cells = <2>;
	interrupt-parent = <&gpio2>;
	interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
	};

	hdmi-encoder@39 {
	compatible = "adi,adv7511w";
	reg = <0x39>;
	interrupt-parent = <&gpio1>;
	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;

	adi,input-depth = <8>;
	adi,input-colorspace = "rgb";
	adi,input-clock = "1x";

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	adv7511_in: endpoint {
	remote-endpoint = <&thc63lvd1024_out>;
	};
	};

	port@1 {
	reg = <1>;
	adv7511_out: endpoint {
	remote-endpoint = <&hdmi_con_out>;
	};
	};
	};
	};

	video-receiver@70 {
	compatible = "adi,adv7482";
	reg = <0x70>;

	interrupt-parent = <&gpio0>;
	interrupt-names = "intrq1", "intrq2";
	interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
	<17 IRQ_TYPE_LEVEL_LOW>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@7 {
	reg = <7>;

	adv7482_ain7: endpoint {
	remote-endpoint = <&cvbs_con>;
	};
	};

	port@8 {
	reg = <8>;

	adv7482_hdmi: endpoint {
	remote-endpoint = <&hdmi_in_con>;
	};
	};

	port@a {
	reg = <10>;

	adv7482_txa: endpoint {
	clock-lanes = <0>;
	data-lanes = <1 2>;
	remote-endpoint = <&csi40_in>;
	};
	};
	};
	};
	};

	&i2c3 {
	status = "okay";

	ak4613: codec@10 {
	compatible = "asahi-kasei,ak4613";
	#sound-dai-cells = <0>;
	reg = <0x10>;
	clocks = <&rcar_sound 3>;

	asahi-kasei,in1-single-end;
	asahi-kasei,in2-single-end;
	asahi-kasei,out1-single-end;
	asahi-kasei,out2-single-end;
	asahi-kasei,out3-single-end;
	asahi-kasei,out4-single-end;
	asahi-kasei,out5-single-end;
	asahi-kasei,out6-single-end;
	};

	cs2000: clk-multiplier@4f {
	#clock-cells = <0>;
	compatible = "cirrus,cs2000-cp";
	reg = <0x4f>;
	clocks = <&audio_clkout>, <&x12_clk>;
	clock-names = "clk_in", "ref_clk";

	assigned-clocks = <&cs2000>;
	assigned-clock-rates = <24576000>; /* 1/1 divide */
	};
	};

	&i2c_dvfs {
	status = "okay";

	clock-frequency = <400000>;

	pmic: pmic@30 {
	pinctrl-0 = <&irq0_pins>;
	pinctrl-names = "default";

	compatible = "rohm,bd9571mwv";
	reg = <0x30>;
	interrupt-parent = <&intc_ex>;
	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
	interrupt-controller;
	#interrupt-cells = <2>;
	gpio-controller;
	#gpio-cells = <2>;
	rohm,ddr-backup-power = <0x1>;
	rohm,rstbmode-level;
	};

	eeprom@50 {
	compatible = "rohm,br24t01", "atmel,24c01";
	reg = <0x50>;
	pagesize = <8>;
	};
	};

	&lvds0 {
	status = "okay";

	clocks = <&cpg CPG_MOD 727>,
	<&x13_clk>,
	<&extal_clk>;
	clock-names = "fck", "dclkin.0", "extal";

	ports {
	port@1 {
	lvds0_out: endpoint {
	remote-endpoint = <&thc63lvd1024_in>;
	};
	};
	};
	};

	&lvds1 {
	/*
	* Even though the LVDS1 output is not connected, the encoder must be
	* enabled to supply a pixel clock to the DU for the DPAD output when
	* LVDS0 is in use.
	*/
	status = "okay";

	clocks = <&cpg CPG_MOD 727>,
	<&x13_clk>,
	<&extal_clk>;
	clock-names = "fck", "dclkin.0", "extal";
	};

	&ohci0 {
	dr_mode = "otg";
	status = "okay";
	};

	&pcie_bus_clk {
	clock-frequency = <100000000>;
	};

	&pciec0 {
	status = "okay";
	};

	&pfc {
	avb_pins: avb {
	groups = "avb_link", "avb_mii";
	function = "avb";
	};

	canfd0_pins: canfd0 {
	groups = "canfd0_data";
	function = "canfd0";
	};

	du_pins: du {
	groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
	function = "du";
	};

	irq0_pins: irq0 {
	groups = "intc_ex_irq0";
	function = "intc_ex";
	};

	keys_pins: keys {
	pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
	bias-pull-up;
	};

	pwm3_pins: pwm3 {
	groups = "pwm3_b";
	function = "pwm3";
	};

	pwm5_pins: pwm5 {
	groups = "pwm5_a";
	function = "pwm5";
	};

	rpc_pins: rpc {
	groups = "rpc_clk2", "rpc_ctrl", "rpc_data", "rpc_reset",
	"rpc_int";
	function = "rpc";
	};

	scif2_pins: scif2 {
	groups = "scif2_data_a";
	function = "scif2";
	};

	sdhi0_pins: sd0 {
	groups = "sdhi0_data4", "sdhi0_ctrl";
	function = "sdhi0";
	power-source = <3300>;
	};

	sdhi0_pins_uhs: sd0_uhs {
	groups = "sdhi0_data4", "sdhi0_ctrl";
	function = "sdhi0";
	power-source = <1800>;
	};

	sdhi1_pins: sd1 {
	groups = "sdhi1_data4", "sdhi1_ctrl";
	function = "sdhi1";
	power-source = <3300>;
	};

	sdhi1_pins_uhs: sd1_uhs {
	groups = "sdhi1_data4", "sdhi1_ctrl";
	function = "sdhi1";
	power-source = <1800>;
	};

	sdhi3_pins: sd3 {
	groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
	function = "sdhi3";
	power-source = <1800>;
	};

	sound_clk_pins: sound_clk {
	groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
	"audio_clkout_a", "audio_clkout1_a";
	function = "audio_clk";
	};

	sound_pins: sound {
	groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
	function = "ssi";
	};

	usb0_pins: usb {
	groups = "usb0_b", "usb0_id";
	function = "usb0";
	};

	usb30_pins: usb30 {
	groups = "usb30";
	function = "usb30";
	};
	};

	&pwm3 {
	pinctrl-0 = <&pwm3_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&pwm5 {
	pinctrl-0 = <&pwm5_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&rcar_sound {
	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
	pinctrl-names = "default";

	/* Single DAI */
	#sound-dai-cells = <0>;

	/* audio_clkout0/1/2/3 */
	#clock-cells = <1>;
	clock-frequency = <12288000 11289600>;

	status = "okay";

	/* update <audio_clk_b> to <cs2000> */
	clocks = <&cpg CPG_MOD 1005>,
	<&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
	<&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
	<&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
	<&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
	<&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
	<&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
	<&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
	<&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
	<&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
	<&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
	<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
	<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
	<&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
	<&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
	<&cpg CPG_CORE R8A77990_CLK_ZA2>;

	rcar_sound,dai {
	dai0 {
	playback = <&ssi0>, <&src0>, <&dvc0>;
	capture = <&ssi1>, <&src1>, <&dvc1>;
	};
	};

	};

	&rpc {
	pinctrl-0 = <&rpc_pins>;
	pinctrl-names = "default";

	/* Left disabled. To be enabled by firmware when unlocked. */

	flash@0 {
	compatible = "cypress,hyperflash", "cfi-flash";
	reg = <0>;

	partitions {
	compatible = "fixed-partitions";
	#address-cells = <1>;
	#size-cells = <1>;

	bootparam@0 {
	reg = <0x00000000 0x040000>;
	read-only;
	};
	bl2@40000 {
	reg = <0x00040000 0x140000>;
	read-only;
	};
	cert_header_sa6@180000 {
	reg = <0x00180000 0x040000>;
	read-only;
	};
	bl31@1c0000 {
	reg = <0x001c0000 0x040000>;
	read-only;
	};
	tee@200000 {
	reg = <0x00200000 0x440000>;
	read-only;
	};
	uboot@640000 {
	reg = <0x00640000 0x100000>;
	read-only;
	};
	dtb@740000 {
	reg = <0x00740000 0x080000>;
	};
	kernel@7c0000 {
	reg = <0x007c0000 0x1400000>;
	};
	user@1bc0000 {
	reg = <0x01bc0000 0x2440000>;
	};
	};
	};
	};

	&rwdt {
	timeout-sec = <60>;
	status = "okay";
	};

	&scif2 {
	pinctrl-0 = <&scif2_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&sdhi0 {
	pinctrl-0 = <&sdhi0_pins>;
	pinctrl-1 = <&sdhi0_pins_uhs>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&vcc_sdhi0>;
	vqmmc-supply = <&vccq_sdhi0>;
	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
	bus-width = <4>;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	status = "okay";
	};

	&sdhi1 {
	pinctrl-0 = <&sdhi1_pins>;
	pinctrl-1 = <&sdhi1_pins_uhs>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&vcc_sdhi1>;
	vqmmc-supply = <&vccq_sdhi1>;
	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
	bus-width = <4>;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	status = "okay";
	};

	&sdhi3 {
	/* used for on-board 8bit eMMC */
	pinctrl-0 = <&sdhi3_pins>;
	pinctrl-1 = <&sdhi3_pins>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&reg_1p8v>;
	mmc-hs200-1_8v;
	mmc-hs400-1_8v;
	bus-width = <8>;
	no-sd;
	no-sdio;
	non-removable;
	full-pwr-cycle-in-suspend;
	status = "okay";
	};

	&ssi1 {
	shared-pin;
	};

	&usb2_phy0 {
	pinctrl-0 = <&usb0_pins>;
	pinctrl-names = "default";

	vbus-supply = <&vbus0_usb2>;
	status = "okay";
	};

	&usb3_peri0 {
	companion = <&xhci0>;
	status = "okay";
	};

	&vin4 {
	status = "okay";
	};

	&vin5 {
	status = "okay";
	};

	&xhci0 {
	pinctrl-0 = <&usb30_pins>;
	pinctrl-names = "default";

	status = "okay";
	};