| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2021 NXP |
| */ |
| |
| /dts-v1/; |
| |
| #include "imx93.dtsi" |
| |
| /{ |
| chosen { |
| stdout-path = &lpuart1; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| audio: audio@a4120000 { |
| compatible = "shared-dma-pool"; |
| reg = <0 0xa4120000 0 0x100000>; |
| no-map; |
| }; |
| }; |
| |
| reg_can2_stby: regulator-can2-stby { |
| compatible = "regulator-fixed"; |
| regulator-name = "can2-stby"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&adp5585gpio 5 GPIO_ACTIVE_LOW>; |
| enable-active-low; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2 { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; |
| regulator-name = "VSD_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| usdhc3_pwrseq: usdhc3_pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&pcal6524 20 GPIO_ACTIVE_LOW>; |
| }; |
| |
| reg_vref_1v8: regulator-adc-vref { |
| compatible = "regulator-fixed"; |
| regulator-name = "vref_1v8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| }; |
| |
| &lpi2c1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_lpi2c1>; |
| pinctrl-1 = <&pinctrl_lpi2c1>; |
| status = "okay"; |
| |
| ptn5110: tcpc@50 { |
| compatible = "nxp,ptn5110"; |
| reg = <0x50>; |
| interrupt-parent = <&pcal6524>; |
| interrupts = <1 IRQ_TYPE_EDGE_FALLING>; |
| status = "okay"; |
| |
| port { |
| typec1_dr_sw: endpoint { |
| remote-endpoint = <&usb1_drd_sw>; |
| }; |
| }; |
| |
| typec1_con: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "dual"; |
| data-role = "dual"; |
| try-power-role = "sink"; |
| source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; |
| sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) |
| PDO_VAR(5000, 20000, 3000)>; |
| op-sink-microwatt = <15000000>; |
| self-powered; |
| }; |
| }; |
| |
| ptn5110_2: tcpc@51 { |
| compatible = "nxp,ptn5110"; |
| reg = <0x51>; |
| interrupt-parent = <&pcal6524>; |
| interrupts = <9 IRQ_TYPE_EDGE_FALLING>; |
| status = "okay"; |
| |
| port { |
| typec2_dr_sw: endpoint { |
| remote-endpoint = <&usb2_drd_sw>; |
| }; |
| }; |
| |
| typec2_con: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "dual"; |
| data-role = "dual"; |
| try-power-role = "sink"; |
| source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; |
| sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) |
| PDO_VAR(5000, 20000, 3000)>; |
| op-sink-microwatt = <15000000>; |
| self-powered; |
| }; |
| }; |
| }; |
| |
| &lpi2c2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <400000>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&pinctrl_lpi2c2>; |
| pinctrl-1 = <&pinctrl_lpi2c2>; |
| status = "okay"; |
| |
| pmic@25 { |
| compatible = "nxp,pca9451a"; |
| reg = <0x25>; |
| pinctrl-names = "default"; |
| interrupt-parent = <&pcal6524>; |
| interrupts = <12 IRQ_TYPE_LEVEL_LOW>; |
| |
| regulators { |
| buck1: BUCK1 { |
| regulator-name = "BUCK1"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <2187500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| buck2: BUCK2 { |
| regulator-name = "BUCK2"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <2187500>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <3125>; |
| }; |
| |
| buck4: BUCK4{ |
| regulator-name = "BUCK4"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck5: BUCK5{ |
| regulator-name = "BUCK5"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck6: BUCK6 { |
| regulator-name = "BUCK6"; |
| regulator-min-microvolt = <600000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1: LDO1 { |
| regulator-name = "LDO1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo2: LDO2 { |
| regulator-name = "LDO2"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo3: LDO3 { |
| regulator-name = "LDO3"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo4: LDO4 { |
| regulator-name = "LDO4"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo5: LDO5 { |
| regulator-name = "LDO5"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| pcal6524: gpio@22 { |
| compatible = "nxp,pcal6524"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcal6524>; |
| reg = <0x22>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&gpio3>; |
| interrupts = <27 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| adp5585gpio: gpio@34 { |
| compatible = "adp5585"; |
| reg = <0x34>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| &lpuart1 { /* console */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &lpuart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "disabled"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| usb-role-switch; |
| disable-over-current; |
| samsung,picophy-pre-emp-curr-control = <3>; |
| samsung,picophy-dc-vol-level-adjust = <7>; |
| status = "okay"; |
| |
| port { |
| usb1_drd_sw: endpoint { |
| remote-endpoint = <&typec1_dr_sw>; |
| }; |
| }; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| usb-role-switch; |
| disable-over-current; |
| samsung,picophy-pre-emp-curr-control = <3>; |
| samsung,picophy-dc-vol-level-adjust = <7>; |
| status = "okay"; |
| |
| port { |
| usb2_drd_sw: endpoint { |
| remote-endpoint = <&typec2_dr_sw>; |
| }; |
| }; |
| }; |
| |
| &usdhc1 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1>; |
| pinctrl-2 = <&pinctrl_usdhc1>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| bus-width = <4>; |
| status = "okay"; |
| no-sdio; |
| no-mmc; |
| }; |
| |
| &usdhc3 { |
| status = "disabled"; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy2>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <5000000>; |
| |
| ethphy2: ethernet-phy@2 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <2>; |
| eee-broken-1000t; |
| rtl821x,aldps-disable; |
| rtl821x,clkout-disable; |
| }; |
| }; |
| }; |
| |
| &eqos { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_eqos>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy1>; |
| status = "okay"; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clock-frequency = <5000000>; |
| |
| ethphy1: ethernet-phy@1 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <1>; |
| eee-broken-1000t; |
| rtl821x,aldps-disable; |
| rtl821x,clkout-disable; |
| }; |
| }; |
| }; |
| |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi>; |
| status = "disabled"; |
| |
| flash0: flash@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <80000000>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <1>; |
| }; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| status = "okay"; |
| |
| pinctrl_flexcan2: flexcan2grp { |
| fsl,pins = < |
| MX93_PAD_GPIO_IO25__CAN2_TX 0x139e |
| MX93_PAD_GPIO_IO27__CAN2_RX 0x139e |
| >; |
| }; |
| |
| pinctrl_flexspi: flexspigrp { |
| fsl,pins = < |
| MX93_PAD_SD3_CMD__FLEXSPI1_A_SS0_B 0x42 |
| MX93_PAD_SD1_DATA3__FLEXSPI1_A_SS1_B 0x42 |
| MX93_PAD_SD3_CLK__FLEXSPI1_A_SCLK 0x42 |
| MX93_PAD_SD1_STROBE__FLEXSPI1_A_DQS 0x42 |
| MX93_PAD_SD3_DATA0__FLEXSPI1_A_DATA00 0x42 |
| MX93_PAD_SD3_DATA1__FLEXSPI1_A_DATA01 0x42 |
| MX93_PAD_SD3_DATA2__FLEXSPI1_A_DATA02 0x42 |
| MX93_PAD_SD3_DATA3__FLEXSPI1_A_DATA03 0x42 |
| MX93_PAD_SD1_DATA4__FLEXSPI1_A_DATA04 0x42 |
| MX93_PAD_SD1_DATA5__FLEXSPI1_A_DATA05 0x42 |
| MX93_PAD_SD1_DATA6__FLEXSPI1_A_DATA06 0x42 |
| MX93_PAD_SD1_DATA7__FLEXSPI1_A_DATA07 0x42 |
| >; |
| }; |
| |
| pinctrl_fec: fecgrp { |
| fsl,pins = < |
| MX93_PAD_ENET2_MDC__ENET1_MDC 0x57e |
| MX93_PAD_ENET2_MDIO__ENET1_MDIO 0x57e |
| MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0 0x57e |
| MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1 0x57e |
| MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2 0x57e |
| MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3 0x57e |
| MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC 0x5fe |
| MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL 0x57e |
| MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0 0x57e |
| MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1 0x57e |
| MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2 0x57e |
| MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3 0x57e |
| MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC 0x5fe |
| MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x57e |
| >; |
| }; |
| |
| pinctrl_eqos: eqosgrp { |
| fsl,pins = < |
| MX93_PAD_ENET1_MDC__ENET_QOS_MDC 0x57e |
| MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO 0x57e |
| MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0 0x57e |
| MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1 0x57e |
| MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2 0x57e |
| MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3 0x57e |
| MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x5fe |
| MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x57e |
| MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0 0x57e |
| MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1 0x57e |
| MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2 0x57e |
| MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3 0x57e |
| MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x5fe |
| MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x57e |
| >; |
| }; |
| |
| pinctrl_lpi2c1: lpi2c1grp { |
| fsl,pins = < |
| MX93_PAD_I2C1_SCL__LPI2C1_SCL 0x40000b9e |
| MX93_PAD_I2C1_SDA__LPI2C1_SDA 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_lpi2c2: lpi2c2grp { |
| fsl,pins = < |
| MX93_PAD_I2C2_SCL__LPI2C2_SCL 0x40000b9e |
| MX93_PAD_I2C2_SDA__LPI2C2_SDA 0x40000b9e |
| >; |
| }; |
| |
| pinctrl_pcal6524: pcal6524grp { |
| fsl,pins = < |
| MX93_PAD_CCM_CLKO2__GPIO3_IO27 0x31e |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX93_PAD_UART1_RXD__LPUART1_RX 0x31e |
| MX93_PAD_UART1_TXD__LPUART1_TX 0x31e |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX93_PAD_UART2_TXD__LPUART2_TX 0x31e |
| MX93_PAD_UART2_RXD__LPUART2_RX 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX93_PAD_SD1_CLK__USDHC1_CLK 0x17fe |
| MX93_PAD_SD1_CMD__USDHC1_CMD 0x13fe |
| MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe |
| MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe |
| MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe |
| MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe |
| MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe |
| MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe |
| MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe |
| MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe |
| MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x17fe |
| >; |
| }; |
| |
| pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { |
| fsl,pins = < |
| MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX93_PAD_SD2_CLK__USDHC2_CLK 0x17fe |
| MX93_PAD_SD2_CMD__USDHC2_CMD 0x13fe |
| MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x13fe |
| MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x13fe |
| MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x13fe |
| MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x13fe |
| MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e |
| >; |
| }; |
| }; |
| |
| &wdog3 { |
| status = "okay"; |
| }; |