| // SPDX-License-Identifier: GPL-2.0 |
| #include <dt-bindings/clock/mt7628-clk.h> |
| #include <dt-bindings/reset/mt7628-reset.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "ralink,mt7628a-soc"; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu@0 { |
| compatible = "mti,mips24KEc"; |
| device_type = "cpu"; |
| reg = <0>; |
| }; |
| }; |
| |
| cpuintc: interrupt-controller { |
| #address-cells = <0>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| compatible = "mti,cpu-interrupt-controller"; |
| }; |
| |
| clk48m: clk48m@0 { |
| compatible = "fixed-clock"; |
| |
| clock-frequency = <48000000>; |
| |
| #clock-cells = <0>; |
| }; |
| |
| palmbus@10000000 { |
| compatible = "palmbus", "simple-bus"; |
| reg = <0x10000000 0x200000>; |
| ranges = <0x0 0x10000000 0x1FFFFF>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| sysc: system-controller@0 { |
| compatible = "ralink,mt7620a-sysc", "syscon"; |
| reg = <0x0 0x100>; |
| }; |
| |
| syscon-reboot { |
| compatible = "syscon-reboot"; |
| regmap = <&sysc>; |
| offset = <0x34>; |
| mask = <0x1>; |
| }; |
| |
| clkctrl: clkctrl@0x2c { |
| reg = <0x2c 0x8>, <0x10 0x4>; |
| reg-names = "syscfg0", "clkcfg"; |
| compatible = "mediatek,mt7628-clk"; |
| #clock-cells = <1>; |
| u-boot,dm-pre-reloc; |
| }; |
| |
| rstctrl: rstctrl@0x34 { |
| reg = <0x34 0x4>; |
| compatible = "mediatek,mtmips-reset"; |
| #reset-cells = <1>; |
| }; |
| |
| pinctrl: pinctrl@60 { |
| compatible = "mediatek,mt7628-pinctrl"; |
| reg = <0x3c 0x2c>, <0x1300 0x100>; |
| reg-names = "gpiomode", "padconf"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&state_default>; |
| |
| state_default: pin_state { |
| }; |
| |
| spi_single_pins: spi_single_pins { |
| groups = "spi"; |
| function = "spi"; |
| }; |
| |
| spi_dual_pins: spi_dual_pins { |
| spi_master_pins { |
| groups = "spi"; |
| function = "spi"; |
| }; |
| |
| spi_cs1_pin { |
| groups = "spi cs1"; |
| function = "spi cs1"; |
| }; |
| }; |
| |
| uart0_pins: uart0_pins { |
| groups = "uart0"; |
| function = "uart0"; |
| }; |
| |
| uart1_pins: uart1_pins { |
| groups = "uart1"; |
| function = "uart1"; |
| }; |
| |
| uart2_pins: uart2_pins { |
| groups = "uart2"; |
| function = "uart2"; |
| }; |
| |
| i2c_pins: i2c_pins { |
| groups = "i2c"; |
| function = "i2c"; |
| }; |
| |
| ephy_iot_mode: ephy_iot_mode { |
| ephy4_1_dis { |
| groups = "ephy4_1_pad"; |
| function = "digital"; |
| }; |
| |
| ephy0_en { |
| groups = "ephy0"; |
| function = "enable"; |
| }; |
| }; |
| |
| ephy_router_mode: ephy_router_mode { |
| ephy4_1_en { |
| groups = "ephy4_1_pad"; |
| function = "analog"; |
| }; |
| |
| ephy0_en { |
| groups = "ephy0"; |
| function = "enable"; |
| }; |
| }; |
| |
| sd_iot_mode: sd_iot_mode { |
| ephy4_1_dis { |
| groups = "ephy4_1_pad"; |
| function = "digital"; |
| }; |
| |
| sdxc_en { |
| groups = "sdmode"; |
| function = "sdxc"; |
| }; |
| |
| sdxc_iot_mode { |
| groups = "sd router"; |
| function = "iot"; |
| }; |
| |
| sd_clk_pad { |
| pins = "sd_clk"; |
| drive-strength-4g = <8>; |
| }; |
| }; |
| |
| sd_router_mode: sd_router_mode { |
| sdxc_router_mode { |
| groups = "sd router"; |
| function = "router"; |
| }; |
| |
| sdxc_map_pins { |
| groups = "gpio0", "i2s", "sdmode", \ |
| "i2c", "uart1"; |
| function = "gpio"; |
| }; |
| |
| sd_clk_pad { |
| pins = "gpio0"; |
| drive-strength-28 = <8>; |
| }; |
| }; |
| |
| emmc_iot_8bit_mode: emmc_iot_8bit_mode { |
| ephy4_1_dis { |
| groups = "ephy4_1_pad"; |
| function = "digital"; |
| }; |
| |
| emmc_en { |
| groups = "sdmode"; |
| function = "sdxc"; |
| }; |
| |
| emmc_iot_mode { |
| groups = "sd router"; |
| function = "iot"; |
| }; |
| |
| emmc_d4_d5 { |
| groups = "uart2"; |
| function = "sdxc d5 d4"; |
| }; |
| |
| emmc_d6 { |
| groups = "pwm1"; |
| function = "sdxc d6"; |
| }; |
| |
| emmc_d7 { |
| groups = "pwm0"; |
| function = "sdxc d7"; |
| }; |
| |
| sd_clk_pad { |
| pins = "sd_clk"; |
| drive-strength-4g = <8>; |
| }; |
| }; |
| }; |
| |
| watchdog: watchdog@100 { |
| compatible = "ralink,mt7628a-wdt", "mediatek,mt7621-wdt"; |
| reg = <0x100 0x30>; |
| |
| resets = <&rstctrl MT7628_TIMER_RST>; |
| reset-names = "wdt"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <24>; |
| }; |
| |
| intc: interrupt-controller@200 { |
| compatible = "ralink,rt2880-intc"; |
| reg = <0x200 0x100>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| resets = <&rstctrl MT7628_INT_RST>; |
| reset-names = "intc"; |
| |
| interrupt-parent = <&cpuintc>; |
| interrupts = <2>; |
| |
| ralink,intc-registers = <0x9c 0xa0 |
| 0x6c 0xa4 |
| 0x80 0x78>; |
| }; |
| |
| memory-controller@300 { |
| compatible = "ralink,mt7620a-memc"; |
| reg = <0x300 0x100>; |
| }; |
| |
| gpio@600 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| compatible = "mtk,mt7628-gpio", "mtk,mt7621-gpio"; |
| reg = <0x600 0x100>; |
| |
| resets = <&rstctrl MT7628_PIO_RST>; |
| reset-names = "pio"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <6>; |
| |
| gpio0: bank@0 { |
| reg = <0>; |
| compatible = "mtk,mt7621-gpio-bank"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpio1: bank@1 { |
| reg = <1>; |
| compatible = "mtk,mt7621-gpio-bank"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpio2: bank@2 { |
| reg = <2>; |
| compatible = "mtk,mt7621-gpio-bank"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| |
| spi0: spi@b00 { |
| compatible = "ralink,mt7621-spi"; |
| reg = <0xb00 0x40>; |
| |
| resets = <&rstctrl MT7628_SPI_RST>; |
| reset-names = "spi"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| clocks = <&clkctrl CLK_SPI>; |
| }; |
| |
| uart0: uartlite@c00 { |
| compatible = "mediatek,hsuart", "ns16550a"; |
| reg = <0xc00 0x100>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pins>; |
| |
| clocks = <&clkctrl CLK_UART0>; |
| |
| resets = <&rstctrl MT7628_UART0_RST>; |
| reset-names = "uart0"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <20>; |
| |
| reg-shift = <2>; |
| }; |
| |
| uart1: uart1@d00 { |
| compatible = "mediatek,hsuart", "ns16550a"; |
| reg = <0xd00 0x100>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_pins>; |
| |
| clocks = <&clkctrl CLK_UART1>; |
| |
| resets = <&rstctrl MT7628_UART1_RST>; |
| reset-names = "uart1"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <21>; |
| |
| reg-shift = <2>; |
| }; |
| |
| uart2: uart2@e00 { |
| compatible = "mediatek,hsuart", "ns16550a"; |
| reg = <0xe00 0x100>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| |
| clocks = <&clkctrl CLK_UART2>; |
| |
| resets = <&rstctrl MT7628_UART2_RST>; |
| reset-names = "uart2"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <22>; |
| |
| reg-shift = <2>; |
| }; |
| }; |
| |
| eth: eth@10110000 { |
| compatible = "mediatek,mt7628-eth"; |
| reg = <0x10100000 0x10000 |
| 0x10110000 0x8000>; |
| |
| resets = <&rstctrl MT7628_EPHY_RST>; |
| reset-names = "ephy"; |
| |
| syscon = <&sysc>; |
| }; |
| |
| usb_phy: usb-phy@10120000 { |
| compatible = "mediatek,mt7628-usbphy"; |
| reg = <0x10120000 0x1000>; |
| |
| #phy-cells = <0>; |
| |
| ralink,sysctl = <&sysc>; |
| |
| resets = <&rstctrl MT7628_UPHY_RST>; |
| reset-names = "phy"; |
| |
| clocks = <&clkctrl CLK_UPHY>; |
| clock-names = "cg"; |
| }; |
| |
| ehci@101c0000 { |
| compatible = "generic-ehci"; |
| reg = <0x101c0000 0x1000>; |
| |
| phys = <&usb_phy>; |
| phy-names = "usb"; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <18>; |
| }; |
| |
| mmc: mmc@10130000 { |
| compatible = "mediatek,mt7620-mmc"; |
| reg = <0x10130000 0x4000>; |
| builtin-cd = <1>; |
| r_smpl = <1>; |
| |
| clocks = <&clk48m>, <&clkctrl CLK_SDXC>; |
| clock-names = "source", "hclk"; |
| |
| resets = <&rstctrl MT7628_SDXC_RST>; |
| |
| status = "disabled"; |
| }; |
| }; |