blob: ad8ea6538c202fd154d728f710296e6e640ec8f5 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2007-2013 Tensilica, Inc.
* Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/core.h>
#include <asm/addrspace.h>
#include <asm/config.h>
/*
* The 'xtfpga' board describes a set of very similar boards with only minimal
* differences.
*/
/*===================*/
/* RAM Layout */
/*===================*/
#if XCHAL_HAVE_PTP_MMU
#define CONFIG_SYS_MEMORY_BASE \
(XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
#define CONFIG_SYS_IO_BASE 0xf0000000
#else
#define CONFIG_SYS_MEMORY_BASE 0x60000000
#define CONFIG_SYS_IO_BASE 0x90000000
#define CONFIG_MAX_MEM_MAPPED 0x10000000
#endif
/* Onboard RAM sizes:
*
* LX60 0x04000000 64 MB
* LX110 0x03000000 48 MB
* LX200 0x06000000 96 MB
* ML605 0x18000000 384 MB
* KC705 0x38000000 896 MB
*
* noMMU configurations can only see first 256MB of onboard memory.
*/
#if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
#define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE
#else
#define CONFIG_SYS_SDRAM_SIZE 0x10000000
#endif
#define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000)
/* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */
#ifdef CONFIG_XTFPGA_LX60
# define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */
#else
# define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */
#endif
/* Memory test is destructive so default must not overlap vectors or U-Boot*/
/* Load address for stand-alone applications.
* MEMADDR cannot be used here, because the definition needs to be
* a plain number as it's used as -Ttext argument for ld in standalone
* example makefile.
* Handle noMMU vs MMUv2 vs MMUv3 distinction here manually.
*/
#if XCHAL_HAVE_PTP_MMU
#if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR
#define CONFIG_STANDALONE_LOAD_ADDR 0x00800000
#else
#define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000
#endif
#else
#define CONFIG_STANDALONE_LOAD_ADDR 0x60800000
#endif
#if defined(CONFIG_MAX_MEM_MAPPED) && \
CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE
#define XTENSA_SYS_TEXT_ADDR \
(MEMADDR(CONFIG_MAX_MEM_MAPPED) - CONFIG_SYS_MONITOR_LEN)
#else
#define XTENSA_SYS_TEXT_ADDR \
(MEMADDR(CONFIG_SYS_SDRAM_SIZE) - CONFIG_SYS_MONITOR_LEN)
#endif
/*==============================*/
/* U-Boot general configuration */
/*==============================*/
/* Console I/O Buffer Size */
/*==============================*/
/* U-Boot autoboot configuration */
/*==============================*/
/*=========================================*/
/* FPGA Registers (board info and control) */
/*=========================================*/
/*
* These assume FPGA bitstreams from Tensilica release RB and up. Earlier
* releases may not provide any/all of these registers or at these offsets.
* Some of the FPGA registers are broken down into bitfields described by
* SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
*/
/* FPGA core clock frequency in Hz (also input to UART) */
#define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/
/*
* DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
* Bits 0..5 set the lower 6 bits of the default ethernet MAC.
* Bit 6 is reserved for future use by Tensilica.
* Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to
* the base of flash * (when on/1) or to the base of RAM (when off/0).
*/
#define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C)
#define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */
#define FPGAREG_MAC_WIDTH 6
#define FPGAREG_MAC_MASK 0x3f
#define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */
#define FPGAREG_BOOT_WIDTH 1
#define FPGAREG_BOOT_MASK 0x80
#define FPGAREG_BOOT_RAM 0
#define FPGAREG_BOOT_FLASH (1<<FPGAREG_BOOT_SHIFT)
/* Force hard reset of board by writing a code to this register */
#define CONFIG_SYS_FPGAREG_RESET IOADDR(0x0D020010) /* Reset board .. */
#define CONFIG_SYS_FPGAREG_RESET_CODE 0x0000DEAD /* by writing this code */
/*====================*/
/* Serial Driver Info */
/*====================*/
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */
/* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
#define CONFIG_SYS_NS16550_CLK get_board_sys_clk()
/*======================*/
/* Ethernet Driver Info */
/*======================*/
#define CONFIG_ETHBASE 00:50:C2:13:6f:00
#define CONFIG_SYS_ETHOC_BASE IOADDR(0x0d030000)
#define CONFIG_SYS_ETHOC_BUFFER_ADDR IOADDR(0x0D800000)
/*=====================*/
/* Flash & Environment */
/*=====================*/
#ifdef CONFIG_XTFPGA_LX60
# define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
#elif defined(CONFIG_XTFPGA_KC705)
# define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000)
#else
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */
# define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */
# define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000)
#endif
/*
* Put environment in top block (64kB)
* Another option would be to put env. in 2nd param block offs 8KB, size 8KB
*/
/* print 'E' for empty sector on flinfo */
#endif /* __CONFIG_H */