blob: 8ab38bbacb657722667aea70476ae7c0584ac765 [file] [log] [blame]
/*
* U-boot - Configuration file for BF561 EZKIT board
*/
#ifndef __CONFIG_BF561_EZKIT_H__
#define __CONFIG_BF561_EZKIT_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf561-0.3
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 30000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 20
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 6
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 9
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_SDRRC_VAL 0x306
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
#define CONFIG_EBIU_AMGCTL_VAL 0x3F
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_NET_MULTI
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x2C010300
#define CONFIG_SMC_USE_32_BIT 1
#define CONFIG_HOSTNAME bf561-ezkit
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 135
/* The BF561-EZKIT uses a top boot flash */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0x20004000
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x10000
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
#define ENV_IS_EMBEDDED
#else
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
#endif
#ifdef ENV_IS_EMBEDDED
/* WARNING - the following is hand-optimized to fit within
* the sector before the environment sector. If it throws
* an error during compilation remove an object here to get
* it linked after the configuration sector.
*/
# define LDS_BOARD_TEXT \
cpu/blackfin/traps.o (.text .text.*); \
cpu/blackfin/interrupt.o (.text .text.*); \
cpu/blackfin/serial.o (.text .text.*); \
common/dlmalloc.o (.text .text.*); \
lib_generic/crc32.o (.text .text.*); \
lib_generic/zlib.o (.text .text.*); \
board/bf561-ezkit/bf561-ezkit.o (.text .text.*); \
. = DEFINED(env_offset) ? env_offset : .; \
common/env_embedded.o (.text .text.*);
#endif
/*
* I2C Settings
*/
#define CONFIG_SOFT_I2C
#ifdef CONFIG_SOFT_I2C
#define PF_SCL PF0
#define PF_SDA PF1
#define I2C_INIT \
do { \
*pFIO0_DIR |= PF_SCL; \
SSYNC(); \
} while (0)
#define I2C_ACTIVE \
do { \
*pFIO0_DIR |= PF_SDA; \
*pFIO0_INEN &= ~PF_SDA; \
SSYNC(); \
} while (0)
#define I2C_TRISTATE \
do { \
*pFIO0_DIR &= ~PF_SDA; \
*pFIO0_INEN |= PF_SDA; \
SSYNC(); \
} while (0)
#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
#define I2C_SDA(bit) \
do { \
if (bit) \
*pFIO0_FLAG_S = PF_SDA; \
else \
*pFIO0_FLAG_C = PF_SDA; \
SSYNC(); \
} while (0)
#define I2C_SCL(bit) \
do { \
if (bit) \
*pFIO0_FLAG_S = PF_SCL; \
else \
*pFIO0_FLAG_C = PF_SCL; \
SSYNC(); \
} while (0)
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
#define CONFIG_SYS_I2C_SPEED 50000
#define CONFIG_SYS_I2C_SLAVE 0
#endif
/*
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif