blob: a469c83fa4eb08f38f91a510f5505e602119cb08 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018-2021 NXP
*/
#ifndef __LX2_COMMON_H
#define __LX2_COMMON_H
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
#define CFG_SYS_FLASH_BASE 0x20000000
/* DDR */
#define CONFIG_VERY_BIG_RAM
#define CFG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CFG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CFG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
#define CFG_SYS_SDRAM_SIZE 0x200000000UL
#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS3 0x53
#define SPD_EEPROM_ADDRESS4 0x54
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
/* Miscellaneous configurable options */
/* SMP Definitinos */
#define CPU_RELEASE_ADDR secondary_boot_addr
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
/* Serial Port */
#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4)
#define CFG_SYS_SERIAL0 0x21c0000
#define CFG_SYS_SERIAL1 0x21d0000
#define CFG_SYS_SERIAL2 0x21e0000
#define CFG_SYS_SERIAL3 0x21f0000
/*below might needs to be removed*/
#define CONFIG_PL01x_PORTS {(void *)CFG_SYS_SERIAL0, \
(void *)CFG_SYS_SERIAL1, \
(void *)CFG_SYS_SERIAL2, \
(void *)CFG_SYS_SERIAL3 }
/* MC firmware */
#define CFG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CFG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CFG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CFG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CFG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
#define CFG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
#endif
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT 0x8
/* RTC */
#define CFG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* Qixis */
#define CFG_SYS_I2C_FPGA_ADDR 0x66
/* USB */
#define COUNTER_FREQUENCY_REAL (get_board_sys_clk() / 4)
#define HWCONFIG_BUFFER_SIZE 128
/* Initial environment variables */
#define XSPI_MC_INIT_CMD \
"sf probe 0:0 && " \
"sf read 0x80640000 0x640000 0x80000 && " \
"sf read $fdt_addr_r 0xf00000 0x100000 && " \
"env exists secureboot && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000; " \
"sf read 0x80a00000 0xa00000 0x300000 && " \
"sf read 0x80e00000 0xe00000 0x100000; " \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD_MC_INIT_CMD \
"mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"mmc read $fdt_addr_r 0x7800 0x800;" \
"env exists secureboot && " \
"mmc read 0x80640000 0x3200 0x20 && " \
"mmc read 0x80680000 0x3400 0x20 && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define SD2_MC_INIT_CMD \
"mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"mmc read $fdt_addr_r 0x7800 0x800;" \
"env exists secureboot && " \
"mmc read 0x80640000 0x3200 0x20 && " \
"mmc read 0x80680000 0x3400 0x20 && " \
"esbc_validate 0x80640000 && " \
"esbc_validate 0x80680000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x600000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"fdt_addr_r=0x90000000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_addr_sd=0x8000\0" \
"kernelhdr_addr_sd=0x3000\0" \
"kernel_size_sd=0x14000\0" \
"kernelhdr_size_sd=0x20\0" \
"console=ttyAMA0,38400n8\0" \
BOOTENV \
"mcmemsize=0x70000000\0" \
XSPI_MC_INIT_CMD \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0"
#define XSPI_NOR_BOOTCOMMAND \
"sf probe 0:0; " \
"sf read 0x806c0000 0x6c0000 0x40000; " \
"env exists mcinitcmd && env exists secureboot" \
" && esbc_validate 0x806c0000; " \
"sf read 0x80d00000 0xd00000 0x100000; " \
"env exists mcinitcmd && " \
"fsl_mc lazyapply dpl 0x80d00000; " \
"run distro_bootcmd;run xspi_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define SD_BOOTCOMMAND \
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
" && mmc read 0x806C0000 0x3600 0x20 " \
"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
#define SD2_BOOTCOMMAND \
"mmc dev 1; env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
" && mmc read 0x806C0000 0x3600 0x20 " \
"&& esbc_validate 0x806C0000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd2_bootcmd;" \
"env exists secureboot && esbc_halt;"
#ifdef CONFIG_CMD_USB
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
#else
#define BOOT_TARGET_DEVICES_USB(func)
#endif
#ifdef CONFIG_MMC
#define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
#else
#define BOOT_TARGET_DEVICES_MMC(func)
#endif
#ifdef CONFIG_SCSI
#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
#else
#define BOOT_TARGET_DEVICES_SCSI(func)
#endif
#ifdef CONFIG_CMD_DHCP
#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
#else
#define BOOT_TARGET_DEVICES_DHCP(func)
#endif
#define BOOT_TARGET_DEVICES(func) \
BOOT_TARGET_DEVICES_USB(func) \
BOOT_TARGET_DEVICES_MMC(func, 0) \
BOOT_TARGET_DEVICES_MMC(func, 1) \
BOOT_TARGET_DEVICES_SCSI(func) \
BOOT_TARGET_DEVICES_DHCP(func)
#include <config_distro_bootcmd.h>
#endif /* __LX2_COMMON_H */