include/configs/ls1021atwr.h - platform/external/u-boot - Gitiles

 /*
  * Copyright 2014 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_ARMV7_PSCI_1_0

 #define CONFIG_ARMV7_SECURE_BASE	OCRAM_BASE_S_ADDR

 #define CONFIG_SYS_FSL_CLK

 #define CONFIG_SKIP_LOWLEVEL_INIT
 #define CONFIG_DEEP_SLEEP

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 16 * 1024 * 1024)

 #define CONFIG_SYS_INIT_RAM_ADDR	OCRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	OCRAM_SIZE

 /*
  * USB
  */

 /*
  * EHCI Support - disbaled by default as
  * there is no signal coming out of soc on
  * this board for this controller. However,
  * the silicon still has this controller,
  * and anyone can use this controller by
  * taking signals out on their board.
  */

 /*#define CONFIG_HAS_FSL_DR_USB*/

 #ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #endif

 /* XHCI Support - enabled by default */
 #define CONFIG_HAS_FSL_XHCI_USB

 #ifdef CONFIG_HAS_FSL_XHCI_USB
 #define CONFIG_USB_XHCI_FSL
 #define CONFIG_USB_MAX_CONTROLLER_COUNT        1
 #endif

 #define CONFIG_SYS_CLK_FREQ		100000000
 #define CONFIG_DDR_CLK_FREQ		100000000

 #define DDR_SDRAM_CFG			0x470c0008
 #define DDR_CS0_BNDS			0x008000bf
 #define DDR_CS0_CONFIG			0x80014302
 #define DDR_TIMING_CFG_0		0x50550004
 #define DDR_TIMING_CFG_1		0xbcb38c56
 #define DDR_TIMING_CFG_2		0x0040d120
 #define DDR_TIMING_CFG_3		0x010e1000
 #define DDR_TIMING_CFG_4		0x00000001
 #define DDR_TIMING_CFG_5		0x03401400
 #define DDR_SDRAM_CFG_2			0x00401010
 #define DDR_SDRAM_MODE			0x00061c60
 #define DDR_SDRAM_MODE_2		0x00180000
 #define DDR_SDRAM_INTERVAL		0x18600618
 #define DDR_DDR_WRLVL_CNTL		0x8655f605
 #define DDR_DDR_WRLVL_CNTL_2		0x05060607
 #define DDR_DDR_WRLVL_CNTL_3		0x05050505
 #define DDR_DDR_CDR1			0x80040000
 #define DDR_DDR_CDR2			0x00000001
 #define DDR_SDRAM_CLK_CNTL		0x02000000
 #define DDR_DDR_ZQ_CNTL			0x89080600
 #define DDR_CS0_CONFIG_2		0
 #define DDR_SDRAM_CFG_MEM_EN		0x80000000
 #define SDRAM_CFG2_D_INIT		0x00000010
 #define DDR_CDR2_VREF_TRAIN_EN		0x00000080
 #define SDRAM_CFG2_FRC_SR		0x80000000
 #define SDRAM_CFG_BI			0x00000001

 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_SYS_FSL_PBL_PBI	board/freescale/ls1021atwr/ls102xa_pbi.cfg
 #endif

 #ifdef CONFIG_SD_BOOT
 #ifdef CONFIG_SD_BOOT_QSPI
 #define CONFIG_SYS_FSL_PBL_RCW	\
 	board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
 #else
 #define CONFIG_SYS_FSL_PBL_RCW	\
 	board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
 #endif
 #define CONFIG_SPL_FRAMEWORK

 #ifdef CONFIG_SECURE_BOOT
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image.
  */
 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
 #endif /* ifdef CONFIG_SECURE_BOOT */

 #define CONFIG_SPL_TEXT_BASE		0x10000000
 #define CONFIG_SPL_MAX_SIZE		0x1a000
 #define CONFIG_SPL_STACK		0x1001d000
 #define CONFIG_SPL_PAD_TO		0x1c000
 #define CONFIG_SYS_TEXT_BASE		0x82000000

 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE + \
 		CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000

 #ifdef CONFIG_U_BOOT_HDR_SIZE
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw u-boot image instead of fit image.
  */
 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN		0x100000
 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
 #endif

 #ifdef CONFIG_QSPI_BOOT
 #define CONFIG_SYS_TEXT_BASE		0x40100000
 #endif

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE		0x60100000
 #endif

 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			0x80000000
 #define PHYS_SDRAM_SIZE			(1u * 1024 * 1024 * 1024)

 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE

 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
 	!defined(CONFIG_QSPI_BOOT)
 #define CONFIG_U_QE
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 #endif

 /*
  * IFC Definitions
  */
 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_FSL_IFC
 #define CONFIG_SYS_FLASH_BASE		0x60000000
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 				CSPR_PORT_SIZE_16 | \
 				CSPR_MSEL_NOR | \
 				CSPR_V)
 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)

 /* NOR Flash Timing Params */
 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
 					CSOR_NOR_TRHZ_80)
 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
 					FTIM0_NOR_TEADC(0x5) | \
 					FTIM0_NOR_TAVDS(0x0) | \
 					FTIM0_NOR_TEAHC(0x5))
 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
 					FTIM1_NOR_TRAD_NOR(0x1A) | \
 					FTIM1_NOR_TSEQRAD_NOR(0x13))
 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
 					FTIM2_NOR_TCH(0x4) | \
 					FTIM2_NOR_TWP(0x1c) | \
 					FTIM2_NOR_TWPH(0x0e))
 #define CONFIG_SYS_NOR_FTIM3		0

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 #define CONFIG_SYS_FLASH_QUIET_TEST
 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE_PHYS }

 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 #define CONFIG_SYS_WRITE_SWAPPED_DATA
 #endif

 /* CPLD */

 #define CONFIG_SYS_CPLD_BASE	0x7fb00000
 #define CPLD_BASE_PHYS		CONFIG_SYS_CPLD_BASE

 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
 					CSPR_PORT_SIZE_8 | \
 					CSPR_MSEL_GPCM | \
 					CSPR_V)
 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
 					CSOR_NOR_NOR_MODE_AVD_NOR | \
 					CSOR_NOR_TRHZ_80)

 /* CPLD Timing parameters for IFC GPCM */
 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xf) | \
 					FTIM0_GPCM_TEADC(0xf) | \
 					FTIM0_GPCM_TEAHC(0xf))
 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
 					FTIM1_GPCM_TRAD(0x3f))
 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
 					FTIM2_GPCM_TCH(0xf) | \
 					FTIM2_GPCM_TWP(0xff))
 #define CONFIG_SYS_FPGA_FTIM3           0x0
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_FPGA_CSPR_EXT
 #define CONFIG_SYS_CSPR1		CONFIG_SYS_FPGA_CSPR
 #define CONFIG_SYS_AMASK1		CONFIG_SYS_FPGA_AMASK
 #define CONFIG_SYS_CSOR1		CONFIG_SYS_FPGA_CSOR
 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_FPGA_FTIM0
 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_FPGA_FTIM1
 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_FPGA_FTIM2
 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_FPGA_FTIM3

 /*
  * Serial Port
  */
 #ifdef CONFIG_LPUART
 #define CONFIG_LPUART_32B_REG
 #else
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550_SERIAL
 #ifndef CONFIG_DM_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #endif
 #define CONFIG_SYS_NS16550_CLK		get_serial_clock()
 #endif

 /*
  * I2C
  */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

 /* EEPROM */
 #define CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM		1
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x53
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5

 /*
  * MMC
  */
 #define CONFIG_FSL_ESDHC

 /* SPI */
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 /* QSPI */
 #define QSPI0_AMBA_BASE			0x40000000
 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
 #define FSL_QSPI_FLASH_NUM		2

 /* DSPI */
 #endif

 /* DM SPI */
 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI)
 #define CONFIG_DM_SPI_FLASH
 #endif

 /*
  * Video
  */
 #ifdef CONFIG_VIDEO_FSL_DCU_FB
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_BMP_LOGO

 #define CONFIG_FSL_DCU_SII9022A
 #define CONFIG_SYS_I2C_DVI_BUS_NUM	1
 #define CONFIG_SYS_I2C_DVI_ADDR		0x39
 #endif

 /*
  * eTSEC
  */
 #define CONFIG_TSEC_ENET

 #ifdef CONFIG_TSEC_ENET
 #define CONFIG_MII
 #define CONFIG_MII_DEFAULT_TSEC		1
 #define CONFIG_TSEC1			1
 #define CONFIG_TSEC1_NAME		"eTSEC1"
 #define CONFIG_TSEC2			1
 #define CONFIG_TSEC2_NAME		"eTSEC2"
 #define CONFIG_TSEC3			1
 #define CONFIG_TSEC3_NAME		"eTSEC3"

 #define TSEC1_PHY_ADDR			2
 #define TSEC2_PHY_ADDR			0
 #define TSEC3_PHY_ADDR			1

 #define TSEC1_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC2_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC3_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)

 #define TSEC1_PHYIDX			0
 #define TSEC2_PHYIDX			0
 #define TSEC3_PHYIDX			0

 #define CONFIG_ETHPRIME			"eTSEC1"

 #define CONFIG_PHY_ATHEROS

 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 #endif

 /* PCIe */
 #define CONFIG_PCIE1		/* PCIE controller 1 */
 #define CONFIG_PCIE2		/* PCIE controller 2 */

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SCAN_SHOW
 #endif

 #define CONFIG_CMDLINE_TAG

 #define CONFIG_PEN_ADDR_BIG_ENDIAN
 #define CONFIG_LAYERSCAPE_NS_ACCESS
 #define CONFIG_SMP_PEN_ADDR		0x01ee0200
 #define COUNTER_FREQUENCY		12500000

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		256

 #define CONFIG_FSL_DEVICE_DISABLE

 #include <config_distro_defaults.h>
 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 0) \
 	func(USB, usb, 0)
 #include <config_distro_bootcmd.h>

 #ifdef CONFIG_LPUART
 #define CONFIG_EXTRA_ENV_SETTINGS       \
 	"bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
 	"initrd_high=0xffffffff\0"      \
 	"fdt_high=0xffffffff\0"		\
 	"fdt_addr=0x64f00000\0"		\
 	"kernel_addr=0x65000000\0"	\
 	"scriptaddr=0x80000000\0"	\
 	"scripthdraddr=0x80080000\0"	\
 	"fdtheader_addr_r=0x80100000\0"	\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"	\
 	"fdt_addr_r=0x90000000\0"	\
 	"ramdisk_addr_r=0xa0000000\0"	\
 	"load_addr=0xa0000000\0"	\
 	"kernel_size=0x2800000\0"	\
 	BOOTENV				\
 	"boot_scripts=ls1021atwr_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1021atwr_bs.out\0"	\
 		"scan_dev_for_boot_part="	\
 			"part list ${devtype} ${devnum} devplist; "	\
 			"env exists devplist || setenv devplist 1; "	\
 			"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "				\
 				"${devnum}:${distro_bootpart} "		\
 				"bootfstype; then "			\
 				"run scan_dev_for_boot; "		\
 			"fi; "			\
 		"done\0"			\
 	"scan_dev_for_boot="				  \
 		"echo Scanning ${devtype} "		  \
 				"${devnum}:${distro_bootpart}...; "  \
 		"for prefix in ${boot_prefixes}; do "	  \
 			"run scan_dev_for_scripts; "	  \
 		"done;"					  \
 		"\0"					  \
 	"boot_a_script="				  \
 		"load ${devtype} ${devnum}:${distro_bootpart} "  \
 			"${scriptaddr} ${prefix}${script}; "    \
 		"env exists secureboot && load ${devtype} "     \
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} " \
 			"&& esbc_validate ${scripthdraddr};"    \
 		"source ${scriptaddr}\0"	  \
 	"installer=load mmc 0:2 $load_addr "	\
 		"/flex_installer_arm32.itb; "		\
 		"bootm $load_addr#ls1021atwr\0"	\
 	"qspi_bootcmd=echo Trying load from qspi..;"	\
 		"sf probe && sf read $load_addr "	\
 		"$kernel_addr $kernel_size && bootm $load_addr#$board\0"	\
 	"nor_bootcmd=echo Trying load from nor..;"	\
 		"cp.b $kernel_addr $load_addr "		\
 		"$kernel_size && bootm $load_addr#$board\0"
 #else
 #define CONFIG_EXTRA_ENV_SETTINGS	\
 	"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
 	"initrd_high=0xffffffff\0"      \
 	"fdt_high=0xffffffff\0"		\
 	"fdt_addr=0x64f00000\0"		\
 	"kernel_addr=0x65000000\0"	\
 	"scriptaddr=0x80000000\0"	\
 	"scripthdraddr=0x80080000\0"	\
 	"fdtheader_addr_r=0x80100000\0"	\
 	"kernelheader_addr_r=0x80200000\0"	\
 	"kernel_addr_r=0x81000000\0"	\
 	"fdt_addr_r=0x90000000\0"	\
 	"ramdisk_addr_r=0xa0000000\0"	\
 	"load_addr=0xa0000000\0"	\
 	"kernel_size=0x2800000\0"	\
 	BOOTENV				\
 	"boot_scripts=ls1021atwr_boot.scr\0"	\
 	"boot_script_hdr=hdr_ls1021atwr_bs.out\0"	\
 		"scan_dev_for_boot_part="	\
 			"part list ${devtype} ${devnum} devplist; "	\
 			"env exists devplist || setenv devplist 1; "	\
 			"for distro_bootpart in ${devplist}; do "	\
 			"if fstype ${devtype} "				\
 				"${devnum}:${distro_bootpart} "		\
 				"bootfstype; then "			\
 				"run scan_dev_for_boot; "		\
 			"fi; "			\
 		"done\0"			\
 	"scan_dev_for_boot="				  \
 		"echo Scanning ${devtype} "		  \
 				"${devnum}:${distro_bootpart}...; "  \
 		"for prefix in ${boot_prefixes}; do "	  \
 			"run scan_dev_for_scripts; "	  \
 		"done;"					  \
 		"\0"					  \
 	"boot_a_script="				  \
 		"load ${devtype} ${devnum}:${distro_bootpart} "  \
 			"${scriptaddr} ${prefix}${script}; "    \
 		"env exists secureboot && load ${devtype} "     \
 			"${devnum}:${distro_bootpart} "		\
 			"${scripthdraddr} ${prefix}${boot_script_hdr} " \
 			"&& esbc_validate ${scripthdraddr};"    \
 		"source ${scriptaddr}\0"	  \
 	"installer=load mmc 0:2 $load_addr "	\
 		"/flex_installer_arm32.itb; "		\
 		"bootm $load_addr#ls1021atwr\0"	\
 	"qspi_bootcmd=echo Trying load from qspi..;"	\
 		"sf probe && sf read $load_addr "	\
 		"$kernel_addr $kernel_size && bootm $load_addr#$board\0"	\
 	"nor_bootcmd=echo Trying load from nor..;"	\
 		"cp.b $kernel_addr $load_addr "		\
 		"$kernel_size && bootm $load_addr#$board\0"
 #endif

 #undef CONFIG_BOOTCOMMAND
 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot"	\
 			   "&& esbc_halt; run qspi_bootcmd;"
 #else
 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot"	\
 			   "&& esbc_halt; run nor_bootcmd;"
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		\
 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE

 #define CONFIG_SYS_MEMTEST_START	0x80000000
 #define CONFIG_SYS_MEMTEST_END		0x9fffffff

 #define CONFIG_SYS_LOAD_ADDR		0x82000000

 #define CONFIG_LS102XA_STREAM_ID

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 #ifdef CONFIG_SPL_BUILD
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 #else
 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif

 #define CONFIG_SYS_QE_FW_ADDR     0x60940000

 /*
  * Environment
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_SD_BOOT)
 #define CONFIG_ENV_OFFSET		0x300000
 #define CONFIG_SYS_MMC_ENV_DEV		0
 #define CONFIG_ENV_SIZE			0x20000
 #elif defined(CONFIG_QSPI_BOOT)
 #define CONFIG_ENV_SIZE			0x2000
 #define CONFIG_ENV_OFFSET		0x300000
 #define CONFIG_ENV_SECT_SIZE		0x10000
 #else
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
 #define CONFIG_ENV_SIZE			0x20000
 #define CONFIG_ENV_SECT_SIZE		0x20000 /* 128K (one sector) */
 #endif

 #define CONFIG_MISC_INIT_R

 #include <asm/fsl_secure_boot.h>
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20) /* Increase max gunzip size */

 #endif
	/*
	* Copyright 2014 Freescale Semiconductor, Inc.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_ARMV7_PSCI_1_0

	#define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR

	#define CONFIG_SYS_FSL_CLK

	#define CONFIG_SKIP_LOWLEVEL_INIT
	#define CONFIG_DEEP_SLEEP

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024)

	#define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE

	/*
	* USB
	*/

	/*
	* EHCI Support - disbaled by default as
	* there is no signal coming out of soc on
	* this board for this controller. However,
	* the silicon still has this controller,
	* and anyone can use this controller by
	* taking signals out on their board.
	*/

	/#define CONFIG_HAS_FSL_DR_USB/

	#ifdef CONFIG_HAS_FSL_DR_USB
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#endif

	/* XHCI Support - enabled by default */
	#define CONFIG_HAS_FSL_XHCI_USB

	#ifdef CONFIG_HAS_FSL_XHCI_USB
	#define CONFIG_USB_XHCI_FSL
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
	#endif

	#define CONFIG_SYS_CLK_FREQ 100000000
	#define CONFIG_DDR_CLK_FREQ 100000000

	#define DDR_SDRAM_CFG 0x470c0008
	#define DDR_CS0_BNDS 0x008000bf
	#define DDR_CS0_CONFIG 0x80014302
	#define DDR_TIMING_CFG_0 0x50550004
	#define DDR_TIMING_CFG_1 0xbcb38c56
	#define DDR_TIMING_CFG_2 0x0040d120
	#define DDR_TIMING_CFG_3 0x010e1000
	#define DDR_TIMING_CFG_4 0x00000001
	#define DDR_TIMING_CFG_5 0x03401400
	#define DDR_SDRAM_CFG_2 0x00401010
	#define DDR_SDRAM_MODE 0x00061c60
	#define DDR_SDRAM_MODE_2 0x00180000
	#define DDR_SDRAM_INTERVAL 0x18600618
	#define DDR_DDR_WRLVL_CNTL 0x8655f605
	#define DDR_DDR_WRLVL_CNTL_2 0x05060607
	#define DDR_DDR_WRLVL_CNTL_3 0x05050505
	#define DDR_DDR_CDR1 0x80040000
	#define DDR_DDR_CDR2 0x00000001
	#define DDR_SDRAM_CLK_CNTL 0x02000000
	#define DDR_DDR_ZQ_CNTL 0x89080600
	#define DDR_CS0_CONFIG_2 0
	#define DDR_SDRAM_CFG_MEM_EN 0x80000000
	#define SDRAM_CFG2_D_INIT 0x00000010
	#define DDR_CDR2_VREF_TRAIN_EN 0x00000080
	#define SDRAM_CFG2_FRC_SR 0x80000000
	#define SDRAM_CFG_BI 0x00000001

	#ifdef CONFIG_RAMBOOT_PBL
	#define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg
	#endif

	#ifdef CONFIG_SD_BOOT
	#ifdef CONFIG_SD_BOOT_QSPI
	#define CONFIG_SYS_FSL_PBL_RCW \
	board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
	#else
	#define CONFIG_SYS_FSL_PBL_RCW \
	board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
	#endif
	#define CONFIG_SPL_FRAMEWORK

	#ifdef CONFIG_SECURE_BOOT
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image.
	*/
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	#endif /* ifdef CONFIG_SECURE_BOOT */

	#define CONFIG_SPL_TEXT_BASE 0x10000000
	#define CONFIG_SPL_MAX_SIZE 0x1a000
	#define CONFIG_SPL_STACK 0x1001d000
	#define CONFIG_SPL_PAD_TO 0x1c000
	#define CONFIG_SYS_TEXT_BASE 0x82000000

	#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \
	CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000

	#ifdef CONFIG_U_BOOT_HDR_SIZE
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw u-boot image instead of fit image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
	#endif

	#ifdef CONFIG_QSPI_BOOT
	#define CONFIG_SYS_TEXT_BASE 0x40100000
	#endif

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0x60100000
	#endif

	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM 0x80000000
	#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
	!defined(CONFIG_QSPI_BOOT)
	#define CONFIG_U_QE
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	#endif

	/*
	* IFC Definitions
	*/
	#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_FSL_IFC
	#define CONFIG_SYS_FLASH_BASE 0x60000000
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE

	#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
	#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \| \
	CSPR_PORT_SIZE_16 \| \
	CSPR_MSEL_NOR \| \
	CSPR_V)
	#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024)

	/* NOR Flash Timing Params */
	#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) \| \
	CSOR_NOR_TRHZ_80)
	#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) \| \
	FTIM0_NOR_TEADC(0x5) \| \
	FTIM0_NOR_TAVDS(0x0) \| \
	FTIM0_NOR_TEAHC(0x5))
	#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) \| \
	FTIM1_NOR_TRAD_NOR(0x1A) \| \
	FTIM1_NOR_TSEQRAD_NOR(0x13))
	#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) \| \
	FTIM2_NOR_TCH(0x4) \| \
	FTIM2_NOR_TWP(0x1c) \| \
	FTIM2_NOR_TWPH(0x0e))
	#define CONFIG_SYS_NOR_FTIM3 0

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	#define CONFIG_SYS_FLASH_QUIET_TEST
	#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }

	#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
	#define CONFIG_SYS_WRITE_SWAPPED_DATA
	#endif

	/* CPLD */

	#define CONFIG_SYS_CPLD_BASE 0x7fb00000
	#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE

	#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
	#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) \| \
	CSPR_PORT_SIZE_8 \| \
	CSPR_MSEL_GPCM \| \
	CSPR_V)
	#define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
	#define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) \| \
	CSOR_NOR_NOR_MODE_AVD_NOR \| \
	CSOR_NOR_TRHZ_80)

	/* CPLD Timing parameters for IFC GPCM */
	#define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) \| \
	FTIM0_GPCM_TEADC(0xf) \| \
	FTIM0_GPCM_TEAHC(0xf))
	#define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) \| \
	FTIM1_GPCM_TRAD(0x3f))
	#define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) \| \
	FTIM2_GPCM_TCH(0xf) \| \
	FTIM2_GPCM_TWP(0xff))
	#define CONFIG_SYS_FPGA_FTIM3 0x0
	#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
	#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
	#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
	#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
	#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
	#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
	#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
	#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
	#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT
	#define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR
	#define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK
	#define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR
	#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0
	#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1
	#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2
	#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3

	/*
	* Serial Port
	*/
	#ifdef CONFIG_LPUART
	#define CONFIG_LPUART_32B_REG
	#else
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#ifndef CONFIG_DM_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#endif
	#define CONFIG_SYS_NS16550_CLK get_serial_clock()
	#endif

	/*
	* I2C
	*/
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */

	/* EEPROM */
	#define CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#define CONFIG_SYS_EEPROM_BUS_NUM 1
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5

	/*
	* MMC
	*/
	#define CONFIG_FSL_ESDHC

	/* SPI */
	#if defined(CONFIG_QSPI_BOOT) \|\| defined(CONFIG_SD_BOOT_QSPI)
	/* QSPI */
	#define QSPI0_AMBA_BASE 0x40000000
	#define FSL_QSPI_FLASH_SIZE (1 << 24)
	#define FSL_QSPI_FLASH_NUM 2

	/* DSPI */
	#endif

	/* DM SPI */
	#if defined(CONFIG_FSL_DSPI) \|\| defined(CONFIG_FSL_QSPI)
	#define CONFIG_DM_SPI_FLASH
	#endif

	/*
	* Video
	*/
	#ifdef CONFIG_VIDEO_FSL_DCU_FB
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_BMP_LOGO

	#define CONFIG_FSL_DCU_SII9022A
	#define CONFIG_SYS_I2C_DVI_BUS_NUM 1
	#define CONFIG_SYS_I2C_DVI_ADDR 0x39
	#endif

	/*
	* eTSEC
	*/
	#define CONFIG_TSEC_ENET

	#ifdef CONFIG_TSEC_ENET
	#define CONFIG_MII
	#define CONFIG_MII_DEFAULT_TSEC 1
	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "eTSEC1"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "eTSEC2"
	#define CONFIG_TSEC3 1
	#define CONFIG_TSEC3_NAME "eTSEC3"

	#define TSEC1_PHY_ADDR 2
	#define TSEC2_PHY_ADDR 0
	#define TSEC3_PHY_ADDR 1

	#define TSEC1_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC2_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)
	#define TSEC3_FLAGS (TSEC_GIGABIT \| TSEC_REDUCED)

	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC3_PHYIDX 0

	#define CONFIG_ETHPRIME "eTSEC1"

	#define CONFIG_PHY_ATHEROS

	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#define CONFIG_HAS_ETH2
	#endif

	/* PCIe */
	#define CONFIG_PCIE1 /* PCIE controller 1 */
	#define CONFIG_PCIE2 /* PCIE controller 2 */

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_SCAN_SHOW
	#endif

	#define CONFIG_CMDLINE_TAG

	#define CONFIG_PEN_ADDR_BIG_ENDIAN
	#define CONFIG_LAYERSCAPE_NS_ACCESS
	#define CONFIG_SMP_PEN_ADDR 0x01ee0200
	#define COUNTER_FREQUENCY 12500000

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 256

	#define CONFIG_FSL_DEVICE_DISABLE

	#include <config_distro_defaults.h>
	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0) \
	func(USB, usb, 0)
	#include <config_distro_bootcmd.h>

	#ifdef CONFIG_LPUART
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_high=0xffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x65000000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"fdt_addr_r=0x90000000\0" \
	"ramdisk_addr_r=0xa0000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	BOOTENV \
	"boot_scripts=ls1021atwr_boot.scr\0" \
	"boot_script_hdr=hdr_ls1021atwr_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"scan_dev_for_boot=" \
	"echo Scanning ${devtype} " \
	"${devnum}:${distro_bootpart}...; " \
	"for prefix in ${boot_prefixes}; do " \
	"run scan_dev_for_scripts; " \
	"done;" \
	"\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"installer=load mmc 0:2 $load_addr " \
	"/flex_installer_arm32.itb; " \
	"bootm $load_addr#ls1021atwr\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size && bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size && bootm $load_addr#$board\0"
	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_high=0xffffffff\0" \
	"fdt_addr=0x64f00000\0" \
	"kernel_addr=0x65000000\0" \
	"scriptaddr=0x80000000\0" \
	"scripthdraddr=0x80080000\0" \
	"fdtheader_addr_r=0x80100000\0" \
	"kernelheader_addr_r=0x80200000\0" \
	"kernel_addr_r=0x81000000\0" \
	"fdt_addr_r=0x90000000\0" \
	"ramdisk_addr_r=0xa0000000\0" \
	"load_addr=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	BOOTENV \
	"boot_scripts=ls1021atwr_boot.scr\0" \
	"boot_script_hdr=hdr_ls1021atwr_bs.out\0" \
	"scan_dev_for_boot_part=" \
	"part list ${devtype} ${devnum} devplist; " \
	"env exists devplist \|\| setenv devplist 1; " \
	"for distro_bootpart in ${devplist}; do " \
	"if fstype ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"bootfstype; then " \
	"run scan_dev_for_boot; " \
	"fi; " \
	"done\0" \
	"scan_dev_for_boot=" \
	"echo Scanning ${devtype} " \
	"${devnum}:${distro_bootpart}...; " \
	"for prefix in ${boot_prefixes}; do " \
	"run scan_dev_for_scripts; " \
	"done;" \
	"\0" \
	"boot_a_script=" \
	"load ${devtype} ${devnum}:${distro_bootpart} " \
	"${scriptaddr} ${prefix}${script}; " \
	"env exists secureboot && load ${devtype} " \
	"${devnum}:${distro_bootpart} " \
	"${scripthdraddr} ${prefix}${boot_script_hdr} " \
	"&& esbc_validate ${scripthdraddr};" \
	"source ${scriptaddr}\0" \
	"installer=load mmc 0:2 $load_addr " \
	"/flex_installer_arm32.itb; " \
	"bootm $load_addr#ls1021atwr\0" \
	"qspi_bootcmd=echo Trying load from qspi..;" \
	"sf probe && sf read $load_addr " \
	"$kernel_addr $kernel_size && bootm $load_addr#$board\0" \
	"nor_bootcmd=echo Trying load from nor..;" \
	"cp.b $kernel_addr $load_addr " \
	"$kernel_size && bootm $load_addr#$board\0"
	#endif

	#undef CONFIG_BOOTCOMMAND
	#if defined(CONFIG_QSPI_BOOT) \|\| defined(CONFIG_SD_BOOT_QSPI)
	#define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \
	"&& esbc_halt; run qspi_bootcmd;"
	#else
	#define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \
	"&& esbc_halt; run nor_bootcmd;"
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE \
	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	#define CONFIG_SYS_MEMTEST_START 0x80000000
	#define CONFIG_SYS_MEMTEST_END 0x9fffffff

	#define CONFIG_SYS_LOAD_ADDR 0x82000000

	#define CONFIG_LS102XA_STREAM_ID

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	#ifdef CONFIG_SPL_BUILD
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
	#else
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	#define CONFIG_SYS_QE_FW_ADDR 0x60940000

	/*
	* Environment
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_SD_BOOT)
	#define CONFIG_ENV_OFFSET 0x300000
	#define CONFIG_SYS_MMC_ENV_DEV 0
	#define CONFIG_ENV_SIZE 0x20000
	#elif defined(CONFIG_QSPI_BOOT)
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_OFFSET 0x300000
	#define CONFIG_ENV_SECT_SIZE 0x10000
	#else
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
	#define CONFIG_ENV_SIZE 0x20000
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
	#endif

	#define CONFIG_MISC_INIT_R

	#include <asm/fsl_secure_boot.h>
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#endif