| /* |
| * (C) Copyright 2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_MPC852T 1 |
| #define CONFIG_NC650 1 |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| |
| /* |
| * 10 MHz - PLL input clock |
| */ |
| #define CONFIG_8xx_OSCLK 10000000 |
| |
| /* |
| * 50 MHz - default CPU clock |
| */ |
| #define CONFIG_8xx_CPUCLK_DEFAULT 50000000 |
| |
| /* |
| * 15 MHz - CPU minimum clock |
| */ |
| #define CFG_8xx_CPUCLK_MIN 15000000 |
| |
| /* |
| * 133 MHz - CPU maximum clock |
| */ |
| #define CFG_8xx_CPUCLK_MAX 133000000 |
| |
| #define CFG_MEASURE_CPUCLK |
| #define CFG_8XX_XIN CONFIG_8xx_OSCLK |
| |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_BOOTCOMMAND \ |
| "bootp;" \ |
| "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ |
| "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ |
| "bootm" |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #undef CONFIG_STATUS_LED /* Status LED disabled */ |
| |
| #define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) |
| |
| #define CONFIG_FEC_ENET 1 /* use FEC ethernet */ |
| #define FEC_ENET |
| #define CONFIG_MII |
| #define CFG_DISCOVER_PHY 1 |
| |
| |
| /* enable I2C and select the hardware/software driver */ |
| #undef CONFIG_HARD_I2C /* I2C with hardware support */ |
| #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ |
| #define CFG_I2C_SPEED 100000 /* 100 kHz */ |
| #define CFG_I2C_SLAVE 0x7f |
| |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define SCL 0x1000 /* PA 3 */ |
| #define SDA 0x2000 /* PA 2 */ |
| |
| #define PAR immr->im_ioport.iop_papar |
| #define DIR immr->im_ioport.iop_padir |
| #define DAT immr->im_ioport.iop_padat |
| |
| #define I2C_INIT {PAR &= ~(SCL | SDA); DIR |= SCL;} |
| #define I2C_ACTIVE (DIR |= SDA) |
| #define I2C_TRISTATE (DIR &= ~SDA) |
| #define I2C_READ ((DAT & SDA) != 0) |
| #define I2C_SDA(bit) if (bit) DAT |= SDA; \ |
| else DAT &= ~SDA |
| #define I2C_SCL(bit) if (bit) DAT |= SCL; \ |
| else DAT &= ~SCL |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| |
| #define CONFIG_RTC_PCF8563 |
| #define CFG_I2C_RTC_ADDR 0x51 |
| |
| #define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ |
| CFG_CMD_ASKENV | \ |
| CFG_CMD_DATE | \ |
| CFG_CMD_DHCP | \ |
| CFG_CMD_I2C | \ |
| CFG_CMD_NAND | \ |
| CFG_CMD_JFFS2 | \ |
| CFG_CMD_NFS | \ |
| CFG_CMD_SNTP ) |
| |
| /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ |
| #include <cmd_confdefs.h> |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CFG_MEMTEST_START 0x0100000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ |
| |
| #define CFG_LOAD_ADDR 0x00100000 |
| |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CFG_IMMR 0xF0000000 |
| #define CFG_IMMR_SIZE ((uint)(64 * 1024)) |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CFG_INIT_RAM_ADDR CFG_IMMR |
| #define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ |
| #define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_FLASH_BASE 0x40000000 |
| |
| #define CFG_RESET_ADDRESS 0xFFF00100 |
| |
| #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CFG_MONITOR_BASE TEXT_BASE |
| #define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ |
| |
| #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_OFFSET 0x00740000 |
| |
| #define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */ |
| #define CFG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if (CONFIG_COMMANDS & CFG_CMD_KGDB) |
| #define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /* |
| * NAND flash support |
| */ |
| #define CFG_MAX_NAND_DEVICE 1 |
| #define NAND_ChipID_UNKNOWN 0x00 |
| #define SECTORSIZE 512 |
| #define NAND_MAX_FLOORS 1 |
| #define NAND_MAX_CHIPS 1 |
| #define ADDR_PAGE 2 |
| #define ADDR_COLUMN_PAGE 3 |
| #define ADDR_COLUMN 1 |
| #define NAND_NO_RB |
| |
| #define NAND_WAIT_READY(nand) udelay(12) |
| #define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2) |
| #define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1) |
| #define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d)) |
| #define READ_NAND(adr) (*(volatile uint8_t *)(adr)) |
| #define NAND_DISABLE_CE(nand) /* nop */ |
| #define NAND_ENABLE_CE(nand) /* nop */ |
| #define NAND_CTL_CLRALE(nandptr) /* nop */ |
| #define NAND_CTL_SETALE(nandptr) /* nop */ |
| #define NAND_CTL_CLRCLE(nandptr) /* nop */ |
| #define NAND_CTL_SETCLE(nandptr) /* nop */ |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| */ |
| #define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CFG_PISCR (PISCR_PS | PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF11 |
| #define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | \ |
| SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ |
| SCCR_DFLCD000 | SCCR_DFALCD00) |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CFG_DER 0 |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ |
| |
| #define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ |
| #define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ |
| |
| /* FLASH timing: Default value of OR0 after reset */ |
| #define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \ |
| OR_SCY_15_CLK | OR_TRLX) |
| |
| #define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) |
| #define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) |
| #define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V) |
| |
| /* |
| * BR2 and OR2 (NAND Flash) - now addressed through UPMB |
| */ |
| #define CFG_NAND_BASE 0x50000000 |
| #define CFG_NAND_SIZE 0x04000000 |
| |
| #define CFG_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ |
| OR_SCY_15_CLK | OR_EHTR | OR_TRLX) |
| |
| #define CFG_BR2_PRELIM ((CFG_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_UPMB | BR_V ) |
| #define CFG_OR2_PRELIM (((-CFG_NAND_SIZE) & OR_AM_MSK) | OR_BI ) |
| |
| /* |
| * BR3 and OR3 (SDRAM) |
| */ |
| #define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ |
| #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ |
| |
| /* |
| * SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) |
| */ |
| #define CFG_OR_TIMING_SDRAM 0x00000A00 |
| |
| #define CFG_OR3_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM) |
| #define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V) |
| |
| /* |
| * BR5 and OR5 (SRAM) |
| */ |
| #define CFG_SRAM_BASE 0x60000000 |
| #define CFG_SRAM_SIZE 0x00080000 |
| |
| #define CFG_OR_TIMING_SRAM (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \ |
| OR_SCY_15_CLK | OR_EHTR | OR_TRLX) |
| |
| #define CFG_BR5_PRELIM ((CFG_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) |
| #define CFG_OR5_PRELIM (((-CFG_SRAM_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_SRAM) |
| |
| |
| /* |
| * 4096 Rows from SDRAM example configuration |
| * 1000 factor s -> ms |
| * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration |
| * 4 Number of refresh cycles per period |
| * 64 Refresh cycle in ms per number of rows |
| */ |
| #define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CFG_MAMR_PTA 39 |
| |
| /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ |
| #define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ |
| #define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ |
| |
| /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ |
| #define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ |
| #define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ |
| |
| /* |
| * MAMR settings for SDRAM |
| */ |
| |
| #define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ |
| MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |
| #define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ |
| MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |
| |
| /* |
| * MBMR settings for NAND flash |
| */ |
| |
| #define CFG_MBMR_NAND ( MBMR_WLFB_5X ) |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ |
| #define CONFIG_JFFS2_NAND_DEV 0 /* nand device jffs2 lives on */ |
| #define CONFIG_JFFS2_NAND_OFF 0 /* start of jffs2 partition */ |
| #define CONFIG_JFFS2_NAND_SIZE 4*1024*1024 /* size of jffs2 partition */ |
| #define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ |
| |
| #endif /* __CONFIG_H */ |