include/configs/s32v234evb.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2015-2016 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:     GPL-2.0+
  *
  * Configuration settings for the Freescale S32V234 EVB board.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #ifndef CONFIG_SPL_BUILD
 #include <config_distro_defaults.h>
 #endif

 #include <asm/arch/imx-regs.h>

 #define CONFIG_S32V234
 #define CONFIG_DM

 /* Config GIC */
 #define CONFIG_GICV2
 #define GICD_BASE 0x7D001000
 #define GICC_BASE 0x7D002000

 #define CONFIG_REMAKE_ELF
 #undef CONFIG_RUN_FROM_IRAM_ONLY

 #define CONFIG_RUN_FROM_DDR1
 #undef CONFIG_RUN_FROM_DDR0

 /* Run by default from DDR1  */
 #ifdef CONFIG_RUN_FROM_DDR0
 #define DDR_BASE_ADDR		0x80000000
 #else
 #define DDR_BASE_ADDR		0xC0000000
 #endif

 #define CONFIG_MACH_TYPE		4146

 #define CONFIG_SKIP_LOWLEVEL_INIT

 /* Config CACHE */
 #define CONFIG_CMD_CACHE

 #define CONFIG_SYS_FULL_VA

 /* Enable passing of ATAGs */
 #define CONFIG_CMDLINE_TAG

 /* SMP Spin Table Definitions */
 #define CPU_RELEASE_ADDR                (CONFIG_SYS_SDRAM_BASE + 0x7fff0)

 /* Generic Timer Definitions */
 #define COUNTER_FREQUENCY               (1000000000)	/* 1000MHz */
 #define CONFIG_SYS_FSL_ERRATUM_A008585

 /* Size of malloc() pool */
 #ifdef CONFIG_RUN_FROM_IRAM_ONLY
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1 * 1024 * 1024)
 #else
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
 #endif
 #define CONFIG_BOARD_EARLY_INIT_F

 #define CONFIG_DM_SERIAL
 #define CONFIG_FSL_LINFLEXUART
 #define LINFLEXUART_BASE		LINFLEXD0_BASE_ADDR

 #define CONFIG_DEBUG_UART_LINFLEXUART
 #define CONFIG_DEBUG_UART_BASE		LINFLEXUART_BASE

 /* Allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SYS_UART_PORT		(1)
 #define CONFIG_BAUDRATE				115200

 #undef CONFIG_CMD_IMLS

 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC_BASE_ADDR
 #define CONFIG_SYS_FSL_ESDHC_NUM	1

 #define CONFIG_CMD_MMC
 #define CONFIG_GENERIC_MMC
 /* #define CONFIG_CMD_EXT2 EXT2 Support */
 #define CONFIG_DOS_PARTITION

 #if 0

 /* Ethernet config */
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_MII
 #define CONFIG_FEC_MXC
 #define CONFIG_MII
 #define IMX_FEC_BASE            ENET_BASE_ADDR
 #define CONFIG_FEC_XCV_TYPE     RMII
 #define CONFIG_FEC_MXC_PHYADDR  0
 #define CONFIG_PHYLIB
 #define CONFIG_PHY_MICREL
 #endif

 #if 0				/* Disable until the I2C driver will be updated */

 /* I2C Configs */
 #define CONFIG_CMD_I2C
 #define CONFIG_HARD_I2C
 #define CONFIG_I2C_MXC
 #define CONFIG_SYS_I2C_BASE		I2C0_BASE_ADDR
 #define CONFIG_SYS_I2C_SPEED		100000
 #endif

 #if 0				/* Disable until the FLASH will be implemented */
 #define CONFIG_SYS_USE_NAND
 #endif

 #ifdef CONFIG_SYS_USE_NAND
 /* Nand Flash Configs */
 #define	CONFIG_CMD_NAND
 #define CONFIG_JFFS2_NAND
 #define MTD_NAND_FSL_NFC_SWECC 1
 #define CONFIG_NAND_FSL_NFC
 #define CONFIG_SYS_NAND_BASE		0x400E0000
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define NAND_MAX_CHIPS			CONFIG_SYS_MAX_NAND_DEVICE
 #define CONFIG_SYS_NAND_SELECT_DEVICE
 #define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
 #endif

 #define CONFIG_LOADADDR			0xC307FFC0
 #define CONFIG_BOOTARGS			"console=ttyLF0 root=/dev/ram rw"

 #define CONFIG_CMD_ENV
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"boot_scripts=boot.scr.uimg boot.scr\0" \
 	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
 	"console=ttyLF0,115200\0" \
 	"fdt_file=s32v234-evb.dtb\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"fdt_addr_r=0xC2000000\0" \
 	"kernel_addr_r=0xC307FFC0\0" \
 	"ramdisk_addr_r=0xC4000000\0" \
 	"ramdisk=rootfs.uimg\0"\
 	"ip_dyn=yes\0" \
 	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 	"update_sd_firmware_filename=u-boot.imx\0" \
 	"update_sd_firmware=" \
 		"if test ${ip_dyn} = yes; then " \
 			"setenv get_cmd dhcp; " \
 		"else " \
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"if mmc dev ${mmcdev}; then "	\
 			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
 				"setexpr fw_sz ${filesize} / 0x200; " \
 				"setexpr fw_sz ${fw_sz} + 1; "	\
 				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 			"fi; "	\
 		"fi\0" \
 	"loadramdisk=fatload mmc ${mmcdev}:${mmcpart} ${ramdisk_addr} ${ramdisk}\0" \
 	"jtagboot=echo Booting using jtag...; " \
 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
 	"jtagsdboot=echo Booting loading Linux with ramdisk from SD...; " \
 		"run loaduimage; run loadramdisk; run loadfdt;"\
 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
 	"boot_net_usb_start=true\0" \
 	BOOTENV

 #define BOOT_TARGET_DEVICES(func) \
 	func(MMC, mmc, 1) \
 	func(MMC, mmc, 0) \
 	func(DHCP, dhcp, na)

 #define CONFIG_BOOTCOMMAND \
 	"run distro_bootcmd"

 #include <config_distro_bootcmd.h>

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LONGHELP	/* undef to save memory */
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #define CONFIG_SYS_PROMPT		"=> "
 #undef CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		\
 			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 #define CONFIG_CMDLINE_EDITING

 #define CONFIG_CMD_MEMTEST
 #define CONFIG_SYS_MEMTEST_START	(DDR_BASE_ADDR)
 #define CONFIG_SYS_MEMTEST_END		(DDR_BASE_ADDR + 0x7C00000)

 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
 #define CONFIG_SYS_HZ				1000

 #define CONFIG_SYS_TEXT_BASE		0x3E800000	/* SDRAM */

 #ifdef CONFIG_RUN_FROM_IRAM_ONLY
 #define CONFIG_SYS_MALLOC_BASE		(DDR_BASE_ADDR)
 #endif

 /*
  * Stack sizes
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE		(128 * 1024)	/* regular stack */

 #if 0
 /* Configure PXE */
 #define CONFIG_BOOTP_PXE
 #define CONFIG_BOOTP_PXE_CLIENTARCH	0x100
 #endif

 /* Physical memory map */
 /* EVB board has 2x256 MB DDR chips, DDR0 and DDR1, u-boot is using just one */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			(DDR_BASE_ADDR)
 #define PHYS_SDRAM_SIZE			(256 * 1024 * 1024)

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 /* FLASH and environment organization */
 #define CONFIG_SYS_NO_FLASH

 #define CONFIG_ENV_SIZE			(8 * 1024)
 #define CONFIG_ENV_IS_IN_MMC

 #define CONFIG_ENV_OFFSET		(12 * 64 * 1024)
 #define CONFIG_SYS_MMC_ENV_DEV		0


 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 #endif
	/*
	* (C) Copyright 2015-2016 Freescale Semiconductor, Inc.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*
	* Configuration settings for the Freescale S32V234 EVB board.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#ifndef CONFIG_SPL_BUILD
	#include <config_distro_defaults.h>
	#endif

	#include <asm/arch/imx-regs.h>

	#define CONFIG_S32V234
	#define CONFIG_DM

	/* Config GIC */
	#define CONFIG_GICV2
	#define GICD_BASE 0x7D001000
	#define GICC_BASE 0x7D002000

	#define CONFIG_REMAKE_ELF
	#undef CONFIG_RUN_FROM_IRAM_ONLY

	#define CONFIG_RUN_FROM_DDR1
	#undef CONFIG_RUN_FROM_DDR0

	/* Run by default from DDR1 */
	#ifdef CONFIG_RUN_FROM_DDR0
	#define DDR_BASE_ADDR 0x80000000
	#else
	#define DDR_BASE_ADDR 0xC0000000
	#endif

	#define CONFIG_MACH_TYPE 4146

	#define CONFIG_SKIP_LOWLEVEL_INIT

	/* Config CACHE */
	#define CONFIG_CMD_CACHE

	#define CONFIG_SYS_FULL_VA

	/* Enable passing of ATAGs */
	#define CONFIG_CMDLINE_TAG

	/* SMP Spin Table Definitions */
	#define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)

	/* Generic Timer Definitions */
	#define COUNTER_FREQUENCY (1000000000) /* 1000MHz */
	#define CONFIG_SYS_FSL_ERRATUM_A008585

	/* Size of malloc() pool */
	#ifdef CONFIG_RUN_FROM_IRAM_ONLY
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1 * 1024 * 1024)
	#else
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
	#endif
	#define CONFIG_BOARD_EARLY_INIT_F

	#define CONFIG_DM_SERIAL
	#define CONFIG_FSL_LINFLEXUART
	#define LINFLEXUART_BASE LINFLEXD0_BASE_ADDR

	#define CONFIG_DEBUG_UART_LINFLEXUART
	#define CONFIG_DEBUG_UART_BASE LINFLEXUART_BASE

	/* Allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_SYS_UART_PORT (1)
	#define CONFIG_BAUDRATE 115200

	#undef CONFIG_CMD_IMLS

	#define CONFIG_FSL_ESDHC
	#define CONFIG_FSL_USDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC_BASE_ADDR
	#define CONFIG_SYS_FSL_ESDHC_NUM 1

	#define CONFIG_CMD_MMC
	#define CONFIG_GENERIC_MMC
	/* #define CONFIG_CMD_EXT2 EXT2 Support */
	#define CONFIG_DOS_PARTITION

	#if 0

	/* Ethernet config */
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_MII
	#define CONFIG_FEC_MXC
	#define CONFIG_MII
	#define IMX_FEC_BASE ENET_BASE_ADDR
	#define CONFIG_FEC_XCV_TYPE RMII
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define CONFIG_PHYLIB
	#define CONFIG_PHY_MICREL
	#endif

	#if 0 /* Disable until the I2C driver will be updated */

	/* I2C Configs */
	#define CONFIG_CMD_I2C
	#define CONFIG_HARD_I2C
	#define CONFIG_I2C_MXC
	#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR
	#define CONFIG_SYS_I2C_SPEED 100000
	#endif

	#if 0 /* Disable until the FLASH will be implemented */
	#define CONFIG_SYS_USE_NAND
	#endif

	#ifdef CONFIG_SYS_USE_NAND
	/* Nand Flash Configs */
	#define CONFIG_CMD_NAND
	#define CONFIG_JFFS2_NAND
	#define MTD_NAND_FSL_NFC_SWECC 1
	#define CONFIG_NAND_FSL_NFC
	#define CONFIG_SYS_NAND_BASE 0x400E0000
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
	#define CONFIG_SYS_NAND_SELECT_DEVICE
	#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
	#endif

	#define CONFIG_LOADADDR 0xC307FFC0
	#define CONFIG_BOOTARGS "console=ttyLF0 root=/dev/ram rw"

	#define CONFIG_CMD_ENV
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"boot_scripts=boot.scr.uimg boot.scr\0" \
	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
	"console=ttyLF0,115200\0" \
	"fdt_file=s32v234-evb.dtb\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_addr_r=0xC2000000\0" \
	"kernel_addr_r=0xC307FFC0\0" \
	"ramdisk_addr_r=0xC4000000\0" \
	"ramdisk=rootfs.uimg\0"\
	"ip_dyn=yes\0" \
	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
	"update_sd_firmware_filename=u-boot.imx\0" \
	"update_sd_firmware=" \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"if mmc dev ${mmcdev}; then " \
	"if ${get_cmd} ${update_sd_firmware_filename}; then " \
	"setexpr fw_sz ${filesize} / 0x200; " \
	"setexpr fw_sz ${fw_sz} + 1; " \
	"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
	"fi; " \
	"fi\0" \
	"loadramdisk=fatload mmc ${mmcdev}:${mmcpart} ${ramdisk_addr} ${ramdisk}\0" \
	"jtagboot=echo Booting using jtag...; " \
	"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
	"jtagsdboot=echo Booting loading Linux with ramdisk from SD...; " \
	"run loaduimage; run loadramdisk; run loadfdt;"\
	"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
	"boot_net_usb_start=true\0" \
	BOOTENV

	#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 1) \
	func(MMC, mmc, 0) \
	func(DHCP, dhcp, na)

	#define CONFIG_BOOTCOMMAND \
	"run distro_bootcmd"

	#include <config_distro_bootcmd.h>

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#define CONFIG_SYS_PROMPT "=> "
	#undef CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE \
	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_CMDLINE_EDITING

	#define CONFIG_CMD_MEMTEST
	#define CONFIG_SYS_MEMTEST_START (DDR_BASE_ADDR)
	#define CONFIG_SYS_MEMTEST_END (DDR_BASE_ADDR + 0x7C00000)

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	#define CONFIG_SYS_HZ 1000

	#define CONFIG_SYS_TEXT_BASE 0x3E800000 /* SDRAM */

	#ifdef CONFIG_RUN_FROM_IRAM_ONLY
	#define CONFIG_SYS_MALLOC_BASE (DDR_BASE_ADDR)
	#endif

	/*
	* Stack sizes
	* The stack sizes are set up in start.S using the settings below
	*/
	#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */

	#if 0
	/* Configure PXE */
	#define CONFIG_BOOTP_PXE
	#define CONFIG_BOOTP_PXE_CLIENTARCH 0x100
	#endif

	/* Physical memory map */
	/* EVB board has 2x256 MB DDR chips, DDR0 and DDR1, u-boot is using just one */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM (DDR_BASE_ADDR)
	#define PHYS_SDRAM_SIZE (256 * 1024 * 1024)

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* FLASH and environment organization */
	#define CONFIG_SYS_NO_FLASH

	#define CONFIG_ENV_SIZE (8 * 1024)
	#define CONFIG_ENV_IS_IN_MMC

	#define CONFIG_ENV_OFFSET (12 * 64 * 1024)
	#define CONFIG_SYS_MMC_ENV_DEV 0


	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	#endif