board/beacon/imx8mp/spl.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks
 *
 */

#include <hang.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/global_data.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/arch/ddr.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <dm/uclass.h>
#include <dm/device.h>

DECLARE_GLOBAL_DATA_PTR;

int spl_board_boot_device(enum boot_device boot_dev_spl)
{
	return BOOT_DEVICE_BOOTROM;
}

void spl_dram_init(void)
{
	ddr_init(&dram_timing);
}

void spl_board_init(void)
{
	if (IS_ENABLED(CONFIG_FSL_CAAM)) {
		struct udevice *dev;
		int ret;

		ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(caam_jr), &dev);
		if (ret)
			printf("Failed to initialize caam_jr: %d\n", ret);
	}
	/*
	 * Set GIC clock to 500Mhz for OD VDD_SOC. Kernel driver does
	 * not allow to change it. Should set the clock after PMIC
	 * setting done. Default is 400Mhz (system_pll1_800m with div = 2)
	 * set by ROM for ND VDD_SOC
	 */
	if (IS_ENABLED(CONFIG_IMX8M_VDD_SOC_850MV)) {
		clock_enable(CCGR_GIC, 0);
		clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5));
		clock_enable(CCGR_GIC, 1);
	}
}

#if CONFIG_IS_ENABLED(DM_PMIC_PCA9450)
int power_init_board(void)
{
	struct udevice *dev;
	int ret;

	ret = pmic_get("pmic@25", &dev);
	if (ret == -ENODEV) {
		puts("No pmic@25\n");
		return 0;
	}
	if (ret != 0)
		return ret;

	/* BUCKxOUT_DVS0/1 control BUCK123 output */
	pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29);

	/*
	 * increase VDD_SOC to typical value 0.95V before first
	 * DRAM access, set DVS1 to 0.85v for suspend.
	 * Enable DVS control through PMIC_STBY_REQ and
	 * set B1_ENMODE=1 (ON by PMIC_ON_REQ=H)
	 */
	if (CONFIG_IS_ENABLED(IMX8M_VDD_SOC_850MV))
		pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x14);
	else
		pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1C);

	pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14);
	pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59);

	/* Kernel uses OD/OD freq for SOC */
	/* To avoid timing risk from SOC to ARM,increase VDD_ARM to OD voltage 0.95v */
	pmic_reg_write(dev, PCA9450_BUCK2OUT_DVS0, 0x1C);

	return 0;
}
#endif

#if IS_ENABLED(CONFIG_SPL_LOAD_FIT)
int board_fit_config_name_match(const char *name)
{
	/* Just empty function now - can't decide what to choose */
	debug("%s: %s\n", __func__, name);

	return 0;
}
#endif

void board_init_f(ulong dummy)
{
	int ret;

	arch_cpu_init();

	init_uart_clk(1);

	ret = spl_early_init();
	if (ret) {
		debug("spl_init() failed: %d\n", ret);
		hang();
	}

	preloader_console_init();

	enable_tzc380();

	power_init_board();

	/* DDR initialization */
	spl_dram_init();
}