blob: 191ac1b73f1c8732f89abf5bc00f5b5cd706c790 [file] [log] [blame]
/*
* Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
*
* Based on the netspace_v2 code which is
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_WIRELESS_SPACE_H
#define _CONFIG_WIRELESS_SPACE_H
/*
* Machine number definition
*/
#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */
#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE
#define CONFIG_IDENT_STRING " Wireless Space"
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
/* SoC name */
#define CONFIG_KW88F6281
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */
#define CONFIG_CMD_ENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_NAND
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#define CONFIG_CMD_USB
/*
* Core clock definition
*/
#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
/*
* SDRAM configuration
*/
#define CONFIG_NR_DRAM_BANKS 1
/*
* Different SDRAM configuration and size for some of the boards derived
* from the Network Space v2
*/
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/* Remove or override few declarations from mv-common.h */
#undef CONFIG_RBTREE
#undef CONFIG_SYS_IDE_MAXBUS
#undef CONFIG_SYS_IDE_MAXDEVICE
#define CONFIG_SYS_IDE_MAXBUS 1
#define CONFIG_SYS_IDE_MAXDEVICE 1
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */
#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */
#define CONFIG_MII
#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#define CONFIG_NETCONSOLE
#define CONFIG_MV88E61XX_SWITCH
#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
#define CONFIG_MV88E61XX_CMD
#define CONFIG_CMD_TFTPPUT
#endif /* CONFIG_CMD_NET */
/*
* SATA Driver configuration
*/
#ifdef CONFIG_MVSATA_IDE
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#endif /* CONFIG_MVSATA_IDE */
/*
* Enable GPI0 support
*/
#define CONFIG_KIRKWOOD_GPIO
/*
* Enable I2C support
*/
#ifdef CONFIG_CMD_I2C
/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */
#endif /* CONFIG_CMD_I2C */
/*
* Partition support
*/
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
/*
* File systems support
*/
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
/*
* Use the HUSH parser
*/
#define CONFIG_SYS_HUSH_PARSER
/*
* Console configuration
*/
#define CONFIG_CONSOLE_MUX
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/*
* Enable device tree support
*/
#define CONFIG_OF_LIBFDT
/*
* Environment variables configurations
*/
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */
#define CONFIG_ENV_SIZE 0x20000 /* 128KB */
#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */
/*
* Board-specific command to make using buttons etc easier
*/
#define CONFIG_WIRELESS_SPACE_CMD
/*
* Default environment variables
*/
#define CONFIG_PREBOOT
#define CONFIG_BOOTARGS "console=ttyS0,115200"
#define CONFIG_BOOTCOMMAND \
"if run usbload || run diskload; then bootm; fi"
#define CONFIG_EXTRA_ENV_SETTINGS \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0" \
"bootfile=uImage\0" \
"loadaddr=0x800000\0" \
"autoload=no\0" \
"netconsole=" \
"set stdin $stdin,nc; " \
"set stdout $stdout,nc; " \
"set stderr $stderr,nc;\0" \
"diskload=ide reset && " \
"ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
"usbload=usb start && " \
"fatload usb 0:1 $loadaddr /boot/$bootfile\0" \
"preboot=" \
"dhcp && run netconsole\0"
#endif /* _CONFIG_WIRELESS_SPACE_H */