| CONFIG_PPC=y |
| CONFIG_TEXT_BASE=0x11000000 |
| CONFIG_SYS_MALLOC_LEN=0x100000 |
| CONFIG_SPL_LIBCOMMON_SUPPORT=y |
| CONFIG_SPL_LIBGENERIC_SUPPORT=y |
| CONFIG_ENV_SIZE=0x2000 |
| CONFIG_ENV_OFFSET=0x0 |
| CONFIG_DEFAULT_DEVICE_TREE="p1020rdb-pc_36b" |
| CONFIG_SPL_TEXT_BASE=0xf8f80000 |
| CONFIG_SPL_MMC=y |
| CONFIG_SPL_SERIAL=y |
| CONFIG_SPL=y |
| CONFIG_MPC85xx=y |
| CONFIG_SYS_INIT_RAM_LOCK=y |
| # CONFIG_CMD_ERRATA is not set |
| CONFIG_TARGET_P1020RDB_PC=y |
| CONFIG_ENABLE_36BIT_PHYS=y |
| CONFIG_SYS_MPC85XX_NO_RESETVEC=y |
| CONFIG_SPL_SYS_MPC85XX_NO_RESETVEC=y |
| CONFIG_PCIE1=y |
| CONFIG_PCIE2=y |
| CONFIG_PHYS_64BIT=y |
| CONFIG_SYS_MONITOR_LEN=786432 |
| CONFIG_MP=y |
| CONFIG_FIT=y |
| CONFIG_FIT_VERBOSE=y |
| CONFIG_OF_BOARD_SETUP=y |
| CONFIG_OF_STDOUT_VIA_ALIAS=y |
| CONFIG_SPL_SYS_MONITOR_BASE=0xF8F80000 |
| CONFIG_FSL_FIXED_MMC_LOCATION=y |
| CONFIG_BOOTDELAY=10 |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="setenv bootargs root=/dev/$bdev rw rootdelay=30 console=$consoledev,$baudrate $othbootargs;usb start;ext2load usb 0:1 $loadaddr /boot/$bootfile;ext2load usb 0:1 $fdtaddr /boot/$fdtfile;bootm $loadaddr - $fdtaddr" |
| CONFIG_BOARD_EARLY_INIT_F=y |
| CONFIG_BOARD_EARLY_INIT_R=y |
| # CONFIG_MISC_INIT_R is not set |
| # CONFIG_SPL_FRAMEWORK is not set |
| CONFIG_SPL_MAX_SIZE=0x20000 |
| CONFIG_SPL_MMC_BOOT=y |
| CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE=y |
| CONFIG_SPL_FLUSH_IMAGE=y |
| CONFIG_SPL_GD_ADDR=0xf8f9c000 |
| CONFIG_SPL_RELOC_STACK=0xf8f9d000 |
| CONFIG_SPL_RELOC_MALLOC=y |
| CONFIG_SPL_RELOC_MALLOC_ADDR=0xf8fa5000 |
| CONFIG_SPL_RELOC_MALLOC_SIZE=0x1b000 |
| CONFIG_SPL_ENV_SUPPORT=y |
| CONFIG_SPL_I2C=y |
| CONFIG_SPL_MPC8XXX_INIT_DDR=y |
| CONFIG_SPL_TARGET="u-boot-with-spl.bin" |
| CONFIG_HUSH_PARSER=y |
| # CONFIG_AUTO_COMPLETE is not set |
| CONFIG_SYS_PBSIZE=276 |
| CONFIG_CMD_IMLS=y |
| CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 |
| CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 |
| CONFIG_CMD_I2C=y |
| CONFIG_LOADS_ECHO=y |
| CONFIG_SYS_LOADS_BAUD_CHANGE=y |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_USB=y |
| CONFIG_CMD_MII=y |
| CONFIG_CMD_PING=y |
| # CONFIG_CMD_HASH is not set |
| CONFIG_CMD_EXT2=y |
| CONFIG_CMD_FAT=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_OVERWRITE=y |
| CONFIG_ENV_IS_IN_MMC=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_USE_BOOTFILE=y |
| CONFIG_BOOTFILE="uImage" |
| CONFIG_USE_ETHPRIME=y |
| CONFIG_ETHPRIME="eTSEC1" |
| CONFIG_LBA48=y |
| CONFIG_DDR_CLK_FREQ=66666666 |
| CONFIG_SYS_SPD_BUS_NUM=1 |
| CONFIG_CHIP_SELECTS_PER_CTRL=1 |
| CONFIG_SYS_DDR_RAW_TIMING=y |
| CONFIG_SYS_BR0_PRELIM_BOOL=y |
| CONFIG_SYS_BR0_PRELIM=0xEF001001 |
| CONFIG_SYS_OR0_PRELIM=0xFC000FF7 |
| CONFIG_SYS_BR2_PRELIM_BOOL=y |
| CONFIG_SYS_BR2_PRELIM=0xFFB00801 |
| CONFIG_SYS_OR2_PRELIM=0xFFFE09FF |
| CONFIG_SYS_BR3_PRELIM_BOOL=y |
| CONFIG_SYS_BR3_PRELIM=0xFFA00801 |
| CONFIG_SYS_OR3_PRELIM=0xFFF009F7 |
| CONFIG_SPL_COMMON_INIT_DDR=y |
| CONFIG_DM_I2C=y |
| CONFIG_SPL_SYS_I2C_LEGACY=y |
| CONFIG_I2C_SET_DEFAULT_BUS_NUM=y |
| CONFIG_SYS_I2C_FSL=y |
| CONFIG_SYS_FSL_I2C_OFFSET=0x3000 |
| CONFIG_SYS_FSL_HAS_I2C2_OFFSET=y |
| CONFIG_SYS_FSL_I2C2_OFFSET=0x3100 |
| CONFIG_SYS_I2C_EEPROM_ADDR=0x52 |
| CONFIG_FSL_ESDHC=y |
| CONFIG_MTD=y |
| CONFIG_MTD_NOR_FLASH=y |
| CONFIG_FLASH_CFI_DRIVER=y |
| CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y |
| CONFIG_SYS_FLASH_EMPTY_INFO=y |
| CONFIG_SYS_FLASH_CFI=y |
| CONFIG_SYS_FLASH_QUIET_TEST=y |
| CONFIG_SYS_MAX_FLASH_SECT=128 |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SF_DEFAULT_SPEED=10000000 |
| CONFIG_SPI_FLASH_SPANSION=y |
| CONFIG_PHY_ATHEROS=y |
| CONFIG_PHY_BROADCOM=y |
| CONFIG_PHY_DAVICOM=y |
| CONFIG_PHY_LXT=y |
| CONFIG_PHY_MARVELL=y |
| CONFIG_PHY_NATSEMI=y |
| CONFIG_PHY_REALTEK=y |
| CONFIG_PHY_SMSC=y |
| CONFIG_PHY_VITESSE=y |
| CONFIG_PHY_FIXED=y |
| CONFIG_DM_MDIO=y |
| CONFIG_PHY_GIGE=y |
| CONFIG_E1000=y |
| CONFIG_MII=y |
| CONFIG_TSEC_ENET=y |
| CONFIG_PCIE_FSL=y |
| CONFIG_DM_RTC=y |
| CONFIG_SYS_NS16550_SERIAL=y |
| CONFIG_SPI=y |
| CONFIG_DM_SPI=y |
| CONFIG_FSL_ESPI=y |
| CONFIG_USB=y |
| CONFIG_USB_EHCI_FSL=y |
| CONFIG_USB_MAX_CONTROLLER_COUNT=2 |
| CONFIG_USB_STORAGE=y |
| CONFIG_ADDR_MAP=y |