| Overview |
| -------- |
| The LS2080A Reference Design (RDB) is a high-performance computing, |
| evaluation, and development platform that supports the QorIQ LS2080A, LS2088A |
| Layerscape Architecture processor. |
| |
| The LS2081A Reference Design (RDB) is a high-performance computing, |
| evaluation, and development platform that supports the QorIQ LS2081A |
| Layerscape Architecture processor.More details in below sections |
| |
| LS2080A, LS2088A, LS2081A SoC Overview |
| -------------------------------------- |
| Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A, |
| LS2081A, LS2088A SoC overview. |
| |
| LS2080ARDB board Overview |
| ----------------------- |
| - SERDES Connections, 16 lanes supporting: |
| - PCI Express - 3.0 |
| - SATA 3.0 |
| - XFI |
| - DDR Controller |
| - Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four |
| chip-selects and two DIMM connectors. Support is up to 2133MT/s. |
| - One port of 40-bits (8-bits ECC) DDR4 which supports four chip-selects |
| and two DIMM connectors. Support is up to 1600MT/s. |
| -IFC/Local Bus |
| - IFC rev. 2.0 implementation supporting Little Endian connection scheme. |
| - 128 MB NOR flash 16-bit data bus |
| - One 2 GB NAND flash with ECC support |
| - CPLD connection |
| - USB 3.0 |
| - Two high speed USB 3.0 ports |
| - First USB 3.0 port configured as Host with Type-A connector |
| - Second USB 3.0 port configured as OTG with micro-AB connector |
| - SDHC adapter |
| - SD Card Rev 2.0 and Rev 3.0 |
| - DSPI |
| - 128 MB high-speed flash Memory for boot code and storage (up to 108MHz) |
| - 4 I2C controllers |
| - Two SATA onboard connectors |
| - UART |
| - ARM JTAG support |
| |
| LS2081ARDB board Overview |
| ------------------------- |
| LS2081ARDB board is similar to LS2080ARDB board |
| with few differences like |
| - Hosts LS2081A SoC |
| - Default boot source is QSPI-boot |
| - Does not have IFC interface |
| - RTC and QSPI flash devices are different |
| - Provides QIXIS access via I2C |
| |
| Memory map from core's view |
| ---------------------------- |
| 0x00_0000_0000 .. 0x00_000F_FFFF Boot Rom |
| 0x00_0100_0000 .. 0x00_0FFF_FFFF CCSR |
| 0x00_1800_0000 .. 0x00_181F_FFFF OCRAM |
| 0x00_2000_0000 .. 0x00_2FFF_FFFF QSPI region #1 |
| 0x00_3000_0000 .. 0x00_3FFF_FFFF IFC region #1 |
| 0x00_8000_0000 .. 0x00_FFFF_FFFF DDR region #1 |
| 0x05_1000_0000 .. 0x05_FFFF_FFFF IFC region #2 |
| 0x80_8000_0000 .. 0xFF_FFFF_FFFF DDR region #2 |
| |
| Other addresses are either reserved, or not used directly by U-Boot. |
| This list should be updated when more addresses are used. |
| |
| IFC region map from core's view |
| ------------------------------- |
| During boot i.e. IFC Region #1:- |
| 0x30000000 - 0x37ffffff : 128MB : NOR flash |
| 0x3C000000 - 0x40000000 : 64MB : CPLD |
| |
| After relocate to DDR i.e. IFC Region #2:- |
| 0x5_1000_0000..0x5_1fff_ffff Memory Hole |
| 0x5_2000_0000..0x5_3fff_ffff IFC CSx (CPLD, NAND and others 512MB) |
| 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB |
| 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet) |
| 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet) |
| |
| Booting Options |
| --------------- |
| a) NOR boot |
| b) NAND boot |
| c) QSPI boot |
| |
| Memory map for NOR boot |
| ------------------------- |
| Image Flash Offset |
| RCW+PBI 0x00000000 |
| Boot firmware (U-Boot) 0x00100000 |
| Boot firmware Environment 0x00300000 |
| PPA firmware 0x00400000 |
| Cortina PHY firmware 0x00980000 |
| DPAA2 MC 0x00A00000 |
| DPAA2 DPL 0x00D00000 |
| DPAA2 DPC 0x00E00000 |
| Kernel.itb 0x01000000 |
| |
| cfg_rcw_src switches needs to be changed for booting from different option. |
| Refer to board documentation for correct switch setting. |
| |
| QSPI boot details |
| =================== |
| Supported only for |
| LS2088ARDB RevF board with LS2088A SoC. |
| |
| Images needs to be copied to QSPI flash |
| as per memory map given below. |
| |
| Memory map for QSPI flash |
| ------------------------- |
| Image Flash Offset |
| RCW+PBI 0x00000000 |
| Boot firmware (U-Boot) 0x00100000 |
| Boot firmware Environment 0x00300000 |
| PPA firmware 0x00400000 |
| Cortina PHY firmware 0x00980000 |
| DPAA2 MC 0x00A00000 |
| DPAA2 DPL 0x00D00000 |
| DPAA2 DPC 0x00E00000 |
| Kernel.itb 0x01000000 |
| |
| Booting Linux flavors which do not support 48-bit VA (< Linux 3.18) |
| ------------------------------------------------------------------- |
| One needs to use appropriate bootargs to boot Linux flavors which do |
| not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown |
| below: |
| |
| => setenv bootargs 'console=ttyS1,115200 root=/dev/ram |
| earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m |
| hugepages=16 mem=2048M' |
| |