| |
| config BITBANGMII |
| bool "Bit-banged ethernet MII management channel support" |
| |
| config MV88E6352_SWITCH |
| bool "Marvell 88E6352 switch support" |
| |
| menuconfig PHYLIB |
| bool "Ethernet PHY (physical media interface) support" |
| help |
| Enable Ethernet PHY (physical media interface) support. |
| |
| if PHYLIB |
| |
| config MV88E61XX_SWITCH |
| bool "Marvel MV88E61xx Ethernet switch PHY support." |
| |
| if MV88E61XX_SWITCH |
| |
| config MV88E61XX_CPU_PORT |
| int "CPU Port" |
| |
| config MV88E61XX_PHY_PORTS |
| hex "Bitmask of PHY Ports" |
| |
| config MV88E61XX_FIXED_PORTS |
| hex "Bitmask of PHYless serdes Ports" |
| |
| endif # MV88E61XX_SWITCH |
| |
| config PHYLIB_10G |
| bool "Generic 10G PHY support" |
| |
| config PHY_AQUANTIA |
| bool "Aquantia Ethernet PHYs support" |
| |
| config PHY_ATHEROS |
| bool "Atheros Ethernet PHYs support" |
| |
| config PHY_BROADCOM |
| bool "Broadcom Ethernet PHYs support" |
| |
| config PHY_CORTINA |
| bool "Cortina Ethernet PHYs support" |
| |
| config PHY_DAVICOM |
| bool "Davicom Ethernet PHYs support" |
| |
| config PHY_ET1011C |
| bool "LSI TruePHY ET1011C support" |
| |
| config PHY_LXT |
| bool "LXT971 Ethernet PHY support" |
| |
| config PHY_MARVELL |
| bool "Marvell Ethernet PHYs support" |
| |
| config PHY_MESON_GXL |
| bool "Amlogic Meson GXL Internal PHY support" |
| |
| config PHY_MICREL |
| bool "Micrel Ethernet PHYs support" |
| help |
| Enable support for the GbE PHYs manufactured by Micrel (now |
| a part of Microchip). This includes drivers for the KSZ804, |
| KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721 |
| either/or KSZ9021 (see the "Micrel KSZ9021 family support" |
| config option for details), and KSZ9031 (if configured). |
| |
| if PHY_MICREL |
| |
| config PHY_MICREL_KSZ9021 |
| bool |
| select PHY_GIGE |
| select PHY_MICREL_KSZ90X1 |
| |
| config PHY_MICREL_KSZ9031 |
| bool |
| select PHY_GIGE |
| select PHY_MICREL_KSZ90X1 |
| |
| config PHY_MICREL_KSZ90X1 |
| bool "Micrel KSZ90x1 family support" |
| select PHY_GIGE |
| help |
| Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If |
| enabled, the extended register read/write for KSZ90x1 PHYs |
| is supported through the 'mdio' command and any RGMII signal |
| delays configured in the device tree will be applied to the |
| PHY during initialization. |
| |
| This should not be enabled at the same time with PHY_MICREL_KSZ8XXX |
| as the KSZ9021 and KS8721 share the same ID. |
| |
| config PHY_MICREL_KSZ8XXX |
| bool "Micrel KSZ8xxx family support" |
| default y if !PHY_MICREL_KSZ90X1 |
| help |
| Enable support for the 8000 series GbE PHYs manufactured by Micrel |
| (now a part of Microchip). This includes drivers for the KSZ804, |
| KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721. |
| |
| This should not be enabled at the same time with PHY_MICREL_KSZ90X1 |
| as the KSZ9021 and KS8721 share the same ID. |
| |
| endif # PHY_MICREL |
| |
| config PHY_MSCC |
| bool "Microsemi Corp Ethernet PHYs support" |
| |
| config PHY_NATSEMI |
| bool "National Semiconductor Ethernet PHYs support" |
| |
| config PHY_REALTEK |
| bool "Realtek Ethernet PHYs support" |
| |
| config RTL8211X_PHY_FORCE_MASTER |
| bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode" |
| depends on PHY_REALTEK |
| help |
| Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F). |
| This can work around link stability and data corruption issues on gigabit |
| links which can occur in slave mode on certain PHYs, e.g. on the |
| RTL8211C(L). |
| |
| Please note that two directly connected devices (i.e. via crossover cable) |
| will not be able to establish a link between each other if they both force |
| master mode. Multiple devices forcing master mode when connected by a |
| network switch do not pose a problem as the switch configures its affected |
| ports into slave mode. |
| |
| This option only affects gigabit links. If you must establish a direct |
| connection between two devices which both force master mode, try forcing |
| the link speed to 100MBit/s. |
| |
| If unsure, say N. |
| |
| config PHY_SMSC |
| bool "Microchip(SMSC) Ethernet PHYs support" |
| |
| config PHY_TERANETICS |
| bool "Teranetics Ethernet PHYs support" |
| |
| config PHY_TI |
| bool "Texas Instruments Ethernet PHYs support" |
| |
| config PHY_VITESSE |
| bool "Vitesse Ethernet PHYs support" |
| |
| config PHY_XILINX |
| bool "Xilinx Ethernet PHYs support" |
| |
| config PHY_FIXED |
| bool "Fixed-Link PHY" |
| depends on DM_ETH |
| help |
| Fixed PHY is used for having a 'fixed-link' to another MAC with a direct |
| connection (MII, RGMII, ...). |
| There is nothing like autoneogation and so |
| on, the link is always up with fixed speed and fixed duplex-setting. |
| More information: doc/device-tree-bindings/net/fixed-link.txt |
| |
| endif #PHYLIB |