blob: 489704633a33243a7ccee629f059db3ad9268bf5 [file] [log] [blame]
/*
* (C) Copyright 2001
* Paul Geerinckx
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <mpc8xx.h>
#include "atm.h"
#include <i2c.h>
/* ------------------------------------------------------------------------- */
static long int dram_size (long int, long int *, long int);
/* ------------------------------------------------------------------------- */
/* used PLD registers */
# define PLD_GCR1_REG (unsigned char *) (0x10000000 + 0)
# define PLD_EXT_RES (unsigned char *) (0x10000000 + 10)
# define PLD_EXT_FETH (unsigned char *) (0x10000000 + 11)
# define PLD_EXT_LED (unsigned char *) (0x10000000 + 12)
# define PLD_EXT_X21 (unsigned char *) (0x10000000 + 13)
#define _NOT_USED_ 0xFFFFFFFF
const uint sdram_table[] =
{
/*
* Single Read. (Offset 0 in UPMA RAM)
*/
0xFE2DB004, 0xF0AA7004, 0xF0A5F400, 0xF3AFFC47, /* last */
_NOT_USED_,
/*
* SDRAM Initialization (offset 5 in UPMA RAM)
*
* This is no UPM entry point. The following definition uses
* the remaining space to establish an initialization
* sequence, which is executed by a RUN command.
*
*/
0xFFFAF834, 0xFFE5B435, /* last */
_NOT_USED_,
/*
* Burst Read. (Offset 8 in UPMA RAM)
*/
0xFE2DB004, 0xF0AF7404, 0xF0AFFC00, 0xF0AFFC00,
0xF0AFFC00, 0xF0AAF800, 0xF1A5E447, /* last */
_NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Single Write. (Offset 18 in UPMA RAM)
*/
0xFE29B300, 0xF1A27304, 0xFFA5F747, /* last */
_NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Burst Write. (Offset 20 in UPMA RAM)
*/
0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
0xF1AAF804, 0xFFA5F447, /* last */
_NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* Refresh (Offset 30 in UPMA RAM)
*/
0xFFAC3884, 0xFFAC3404, 0xFFAFFC04, 0xFFAFFC84,
0xFFAFFC07, /* last */
_NOT_USED_, _NOT_USED_, _NOT_USED_,
/*
* MRS sequence (Offset 38 in UPMA RAM)
*/
0xFFAAB834, 0xFFA57434, 0xFFAFFC05, /* last */
_NOT_USED_,
/*
* Exception. (Offset 3c in UPMA RAM)
*/
0xFFAFFC04, 0xFFAFFC05, /* last */
_NOT_USED_, _NOT_USED_,
};
/* ------------------------------------------------------------------------- */
long int initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
volatile iop8xx_t *iop = &immap->im_ioport;
volatile fec_t *fecp = &immap->im_cpm.cp_fec;
long int size;
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
/*
* Preliminary prescaler for refresh (depends on number of
* banks): This value is selected for four cycles every 62.4 us
* with two SDRAM banks or four cycles every 31.2 us with one
* bank. It will be adjusted after memory sizing.
*/
memctl->memc_mptpr = CFG_MPTPR;
memctl->memc_mar = 0x00000088;
/*
* Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
* preliminary addresses - these have to be modified after the
* SDRAM size has been determined.
*/
memctl->memc_or2 = CFG_OR2_PRELIM;
memctl->memc_br2 = CFG_BR2_PRELIM;
memctl->memc_mamr = CFG_MAMR & (~(MAMR_PTAE)); /* no refresh yet */
udelay(200);
/* perform SDRAM initializsation sequence */
memctl->memc_mcr = 0x80004105; /* SDRAM bank 0 */
udelay(1);
memctl->memc_mcr = 0x80004230; /* SDRAM bank 0 - execute twice */
udelay(1);
memctl->memc_mcr = 0x80004105; /* SDRAM precharge */
udelay(1);
memctl->memc_mcr = 0x80004030; /* SDRAM 16x autorefresh */
udelay(1);
memctl->memc_mcr = 0x80004138; /* SDRAM upload parameters */
udelay(1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay (1000);
/*
* Check Bank 0 Memory Size for re-configuration
*
*/
size = dram_size (CFG_MAMR, (ulong *)SDRAM_BASE_PRELIM, SDRAM_MAX_SIZE);
udelay (1000);
memctl->memc_mamr = CFG_MAMR;
udelay (1000);
/*
* Final mapping
*/
memctl->memc_or2 = ((-size) & 0xFFFF0000) | CFG_OR2_PRELIM;
memctl->memc_br2 = ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V);
udelay(10000);
/* prepare pin multiplexing for fast ethernet */
atmLoad();
fecp->fec_ecntrl = 0x00000004; /* rev D3 pinmux SET */
iop->iop_pdpar |= 0x0080; /* set pin as MII_clock */
return (size);
}
/* ------------------------------------------------------------------------- */
/*
* Check memory range for valid RAM. A simple memory test determines
* the actually available RAM size between addresses `base' and
* `base + maxsize'. Some (not all) hardware errors are detected:
* - short between address lines
* - short between data lines
*/
static long int dram_size (long int mamr_value, long int *base, long int maxsize)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
volatile long int *addr;
ulong cnt, val;
ulong save[32]; /* to make test non-destructive */
unsigned char i = 0;
memctl->memc_mamr = mamr_value;
for (cnt = maxsize/sizeof(long); cnt > 0; cnt >>= 1) {
addr = base + cnt; /* pointer arith! */
save[i++] = *addr;
*addr = ~cnt;
}
/* write 0 to base address */
addr = base;
save[i] = *addr;
*addr = 0;
/* check at base address */
if ((val = *addr) != 0) {
*addr = save[i];
return (0);
}
for (cnt = 1; cnt <= maxsize/sizeof(long); cnt <<= 1) {
addr = base + cnt; /* pointer arith! */
val = *addr;
*addr = save[--i];
if (val != (~cnt)) {
return (cnt * sizeof(long));
}
}
return (maxsize);
}
/*
* Check Board Identity:
*/
int checkboard (void)
{
return (0);
}
void board_serial_init(void)
{
;/* nothing to do here */
}
void board_ether_init(void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile iop8xx_t *iop = &immap->im_ioport;
volatile fec_t *fecp = &immap->im_cpm.cp_fec;
atmLoad();
fecp->fec_ecntrl = 0x00000004; /* rev D3 pinmux SET */
iop->iop_pdpar |= 0x0080; /* set pin as MII_clock */
}
int board_pre_init (void)
{
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile cpmtimer8xx_t *timers = &immap->im_cpmtimer;
volatile memctl8xx_t *memctl = &immap->im_memctl;
volatile iop8xx_t *iop = &immap->im_ioport;
/* configure the LED timing output pins - port A pin 4 */
iop->iop_papar = 0x0800;
iop->iop_padir = 0x0800;
/* start timer 2 for the 4hz LED blink rate */
timers->cpmt_tmr2 = 0xff2c; /* 4hz for 64mhz */
timers->cpmt_trr2 = 0x000003d0; /* clk/16 , prescale=256 */
timers->cpmt_tgcr = 0x00000810; /* run timer 2 */
/* chip select for PLD access */
memctl->memc_br6 = 0x10000401;
memctl->memc_or6 = 0xFC000908;
/* PLD initial values ( set LEDs, remove reset on LXT) */
*PLD_GCR1_REG = 0x06;
*PLD_EXT_RES = 0xC0;
*PLD_EXT_FETH = 0x40;
*PLD_EXT_LED = 0xFF;
*PLD_EXT_X21 = 0x04;
return 0;
}
void board_get_enetaddr (uchar *addr)
{
int i;
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile cpm8xx_t *cpm = &immap->im_cpm;
unsigned int rccrtmp;
char default_mac_addr[] = {0x00, 0x08, 0x01, 0x02, 0x03, 0x04};
for (i=0; i<6; i++)
addr[i] = default_mac_addr[i];
printf("There is an error in the i2c driver .. /n");
printf("You need to fix it first....../n");
rccrtmp = cpm->cp_rccr;
cpm->cp_rccr |= 0x0020;
i2c_reg_read(0xa0, 0);
printf ("seep = '-%c-%c-%c-%c-%c-%c-'\n",
i2c_reg_read(0xa0, 0), i2c_reg_read(0xa0, 0), i2c_reg_read(0xa0, 0),
i2c_reg_read(0xa0, 0), i2c_reg_read(0xa0, 0), i2c_reg_read(0xa0, 0) );
cpm->cp_rccr = rccrtmp;
}