| // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| /* |
| * (C) Copyright 2016-2017 Rockchip Inc. |
| * |
| * Adapted from coreboot. |
| */ |
| |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <dt-structs.h> |
| #include <ram.h> |
| #include <regmap.h> |
| #include <syscon.h> |
| #include <asm/io.h> |
| #include <asm/arch-rockchip/clock.h> |
| #include <asm/arch-rockchip/cru_rk3399.h> |
| #include <asm/arch-rockchip/grf_rk3399.h> |
| #include <asm/arch-rockchip/hardware.h> |
| #include <asm/arch-rockchip/sdram_common.h> |
| #include <asm/arch-rockchip/sdram_rk3399.h> |
| #include <linux/err.h> |
| #include <time.h> |
| |
| #define PRESET_SGRF_HOLD(n) ((0x1 << (6 + 16)) | ((n) << 6)) |
| #define PRESET_GPIO0_HOLD(n) ((0x1 << (7 + 16)) | ((n) << 7)) |
| #define PRESET_GPIO1_HOLD(n) ((0x1 << (8 + 16)) | ((n) << 8)) |
| |
| #define PHY_DRV_ODT_HI_Z 0x0 |
| #define PHY_DRV_ODT_240 0x1 |
| #define PHY_DRV_ODT_120 0x8 |
| #define PHY_DRV_ODT_80 0x9 |
| #define PHY_DRV_ODT_60 0xc |
| #define PHY_DRV_ODT_48 0xd |
| #define PHY_DRV_ODT_40 0xe |
| #define PHY_DRV_ODT_34_3 0xf |
| |
| struct chan_info { |
| struct rk3399_ddr_pctl_regs *pctl; |
| struct rk3399_ddr_pi_regs *pi; |
| struct rk3399_ddr_publ_regs *publ; |
| struct rk3399_msch_regs *msch; |
| }; |
| |
| struct dram_info { |
| #if defined(CONFIG_TPL_BUILD) || \ |
| (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD)) |
| struct chan_info chan[2]; |
| struct clk ddr_clk; |
| struct rk3399_cru *cru; |
| struct rk3399_pmucru *pmucru; |
| struct rk3399_pmusgrf_regs *pmusgrf; |
| struct rk3399_ddr_cic_regs *cic; |
| #endif |
| struct ram_info info; |
| struct rk3399_pmugrf_regs *pmugrf; |
| }; |
| |
| #if defined(CONFIG_TPL_BUILD) || \ |
| (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD)) |
| |
| struct rockchip_dmc_plat { |
| #if CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct dtd_rockchip_rk3399_dmc dtplat; |
| #else |
| struct rk3399_sdram_params sdram_params; |
| #endif |
| struct regmap *map; |
| }; |
| |
| static void copy_to_reg(u32 *dest, const u32 *src, u32 n) |
| { |
| int i; |
| |
| for (i = 0; i < n / sizeof(u32); i++) { |
| writel(*src, dest); |
| src++; |
| dest++; |
| } |
| } |
| |
| static void phy_dll_bypass_set(struct rk3399_ddr_publ_regs *ddr_publ_regs, |
| u32 freq) |
| { |
| u32 *denali_phy = ddr_publ_regs->denali_phy; |
| |
| /* From IP spec, only freq small than 125 can enter dll bypass mode */ |
| if (freq <= 125) { |
| /* phy_sw_master_mode_X PHY_86/214/342/470 4bits offset_8 */ |
| setbits_le32(&denali_phy[86], (0x3 << 2) << 8); |
| setbits_le32(&denali_phy[214], (0x3 << 2) << 8); |
| setbits_le32(&denali_phy[342], (0x3 << 2) << 8); |
| setbits_le32(&denali_phy[470], (0x3 << 2) << 8); |
| |
| /* phy_adrctl_sw_master_mode PHY_547/675/803 4bits offset_16 */ |
| setbits_le32(&denali_phy[547], (0x3 << 2) << 16); |
| setbits_le32(&denali_phy[675], (0x3 << 2) << 16); |
| setbits_le32(&denali_phy[803], (0x3 << 2) << 16); |
| } else { |
| /* phy_sw_master_mode_X PHY_86/214/342/470 4bits offset_8 */ |
| clrbits_le32(&denali_phy[86], (0x3 << 2) << 8); |
| clrbits_le32(&denali_phy[214], (0x3 << 2) << 8); |
| clrbits_le32(&denali_phy[342], (0x3 << 2) << 8); |
| clrbits_le32(&denali_phy[470], (0x3 << 2) << 8); |
| |
| /* phy_adrctl_sw_master_mode PHY_547/675/803 4bits offset_16 */ |
| clrbits_le32(&denali_phy[547], (0x3 << 2) << 16); |
| clrbits_le32(&denali_phy[675], (0x3 << 2) << 16); |
| clrbits_le32(&denali_phy[803], (0x3 << 2) << 16); |
| } |
| } |
| |
| static void set_memory_map(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| const struct rk3399_sdram_channel *sdram_ch = ¶ms->ch[channel]; |
| u32 *denali_ctl = chan->pctl->denali_ctl; |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 cs_map; |
| u32 reduc; |
| u32 row; |
| |
| /* Get row number from ddrconfig setting */ |
| if (sdram_ch->ddrconfig < 2 || sdram_ch->ddrconfig == 4) |
| row = 16; |
| else if (sdram_ch->ddrconfig == 3) |
| row = 14; |
| else |
| row = 15; |
| |
| cs_map = (sdram_ch->rank > 1) ? 3 : 1; |
| reduc = (sdram_ch->bw == 2) ? 0 : 1; |
| |
| /* Set the dram configuration to ctrl */ |
| clrsetbits_le32(&denali_ctl[191], 0xF, (12 - sdram_ch->col)); |
| clrsetbits_le32(&denali_ctl[190], (0x3 << 16) | (0x7 << 24), |
| ((3 - sdram_ch->bk) << 16) | |
| ((16 - row) << 24)); |
| |
| clrsetbits_le32(&denali_ctl[196], 0x3 | (1 << 16), |
| cs_map | (reduc << 16)); |
| |
| /* PI_199 PI_COL_DIFF:RW:0:4 */ |
| clrsetbits_le32(&denali_pi[199], 0xF, (12 - sdram_ch->col)); |
| |
| /* PI_155 PI_ROW_DIFF:RW:24:3 PI_BANK_DIFF:RW:16:2 */ |
| clrsetbits_le32(&denali_pi[155], (0x3 << 16) | (0x7 << 24), |
| ((3 - sdram_ch->bk) << 16) | |
| ((16 - row) << 24)); |
| /* PI_41 PI_CS_MAP:RW:24:4 */ |
| clrsetbits_le32(&denali_pi[41], 0xf << 24, cs_map << 24); |
| if (sdram_ch->rank == 1 && params->base.dramtype == DDR3) |
| writel(0x2EC7FFFF, &denali_pi[34]); |
| } |
| |
| static void set_ds_odt(const struct chan_info *chan, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_phy = chan->publ->denali_phy; |
| |
| u32 tsel_idle_en, tsel_wr_en, tsel_rd_en; |
| u32 tsel_idle_select_p, tsel_wr_select_p, tsel_rd_select_p; |
| u32 ca_tsel_wr_select_p, ca_tsel_wr_select_n; |
| u32 tsel_idle_select_n, tsel_wr_select_dq_n, tsel_rd_select_n; |
| u32 reg_value; |
| |
| if (params->base.dramtype == LPDDR4) { |
| tsel_rd_select_p = PHY_DRV_ODT_HI_Z; |
| tsel_wr_select_p = PHY_DRV_ODT_40; |
| ca_tsel_wr_select_p = PHY_DRV_ODT_40; |
| tsel_idle_select_p = PHY_DRV_ODT_HI_Z; |
| |
| tsel_rd_select_n = PHY_DRV_ODT_240; |
| tsel_wr_select_dq_n = PHY_DRV_ODT_40; |
| ca_tsel_wr_select_n = PHY_DRV_ODT_40; |
| tsel_idle_select_n = PHY_DRV_ODT_240; |
| } else if (params->base.dramtype == LPDDR3) { |
| tsel_rd_select_p = PHY_DRV_ODT_240; |
| tsel_wr_select_p = PHY_DRV_ODT_34_3; |
| ca_tsel_wr_select_p = PHY_DRV_ODT_48; |
| tsel_idle_select_p = PHY_DRV_ODT_240; |
| |
| tsel_rd_select_n = PHY_DRV_ODT_HI_Z; |
| tsel_wr_select_dq_n = PHY_DRV_ODT_34_3; |
| ca_tsel_wr_select_n = PHY_DRV_ODT_48; |
| tsel_idle_select_n = PHY_DRV_ODT_HI_Z; |
| } else { |
| tsel_rd_select_p = PHY_DRV_ODT_240; |
| tsel_wr_select_p = PHY_DRV_ODT_34_3; |
| ca_tsel_wr_select_p = PHY_DRV_ODT_34_3; |
| tsel_idle_select_p = PHY_DRV_ODT_240; |
| |
| tsel_rd_select_n = PHY_DRV_ODT_240; |
| tsel_wr_select_dq_n = PHY_DRV_ODT_34_3; |
| ca_tsel_wr_select_n = PHY_DRV_ODT_34_3; |
| tsel_idle_select_n = PHY_DRV_ODT_240; |
| } |
| |
| if (params->base.odt == 1) |
| tsel_rd_en = 1; |
| else |
| tsel_rd_en = 0; |
| |
| tsel_wr_en = 0; |
| tsel_idle_en = 0; |
| |
| /* |
| * phy_dq_tsel_select_X 24bits DENALI_PHY_6/134/262/390 offset_0 |
| * sets termination values for read/idle cycles and drive strength |
| * for write cycles for DQ/DM |
| */ |
| reg_value = tsel_rd_select_n | (tsel_rd_select_p << 0x4) | |
| (tsel_wr_select_dq_n << 8) | (tsel_wr_select_p << 12) | |
| (tsel_idle_select_n << 16) | (tsel_idle_select_p << 20); |
| clrsetbits_le32(&denali_phy[6], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[134], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[262], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[390], 0xffffff, reg_value); |
| |
| /* |
| * phy_dqs_tsel_select_X 24bits DENALI_PHY_7/135/263/391 offset_0 |
| * sets termination values for read/idle cycles and drive strength |
| * for write cycles for DQS |
| */ |
| clrsetbits_le32(&denali_phy[7], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[135], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[263], 0xffffff, reg_value); |
| clrsetbits_le32(&denali_phy[391], 0xffffff, reg_value); |
| |
| /* phy_adr_tsel_select_ 8bits DENALI_PHY_544/672/800 offset_0 */ |
| reg_value = ca_tsel_wr_select_n | (ca_tsel_wr_select_p << 0x4); |
| clrsetbits_le32(&denali_phy[544], 0xff, reg_value); |
| clrsetbits_le32(&denali_phy[672], 0xff, reg_value); |
| clrsetbits_le32(&denali_phy[800], 0xff, reg_value); |
| |
| /* phy_pad_addr_drive 8bits DENALI_PHY_928 offset_0 */ |
| clrsetbits_le32(&denali_phy[928], 0xff, reg_value); |
| |
| /* phy_pad_rst_drive 8bits DENALI_PHY_937 offset_0 */ |
| clrsetbits_le32(&denali_phy[937], 0xff, reg_value); |
| |
| /* phy_pad_cke_drive 8bits DENALI_PHY_935 offset_0 */ |
| clrsetbits_le32(&denali_phy[935], 0xff, reg_value); |
| |
| /* phy_pad_cs_drive 8bits DENALI_PHY_939 offset_0 */ |
| clrsetbits_le32(&denali_phy[939], 0xff, reg_value); |
| |
| /* phy_pad_clk_drive 8bits DENALI_PHY_929 offset_0 */ |
| clrsetbits_le32(&denali_phy[929], 0xff, reg_value); |
| |
| /* phy_pad_fdbk_drive 23bit DENALI_PHY_924/925 */ |
| clrsetbits_le32(&denali_phy[924], 0xff, |
| tsel_wr_select_dq_n | (tsel_wr_select_p << 4)); |
| clrsetbits_le32(&denali_phy[925], 0xff, |
| tsel_rd_select_n | (tsel_rd_select_p << 4)); |
| |
| /* phy_dq_tsel_enable_X 3bits DENALI_PHY_5/133/261/389 offset_16 */ |
| reg_value = (tsel_rd_en | (tsel_wr_en << 1) | (tsel_idle_en << 2)) |
| << 16; |
| clrsetbits_le32(&denali_phy[5], 0x7 << 16, reg_value); |
| clrsetbits_le32(&denali_phy[133], 0x7 << 16, reg_value); |
| clrsetbits_le32(&denali_phy[261], 0x7 << 16, reg_value); |
| clrsetbits_le32(&denali_phy[389], 0x7 << 16, reg_value); |
| |
| /* phy_dqs_tsel_enable_X 3bits DENALI_PHY_6/134/262/390 offset_24 */ |
| reg_value = (tsel_rd_en | (tsel_wr_en << 1) | (tsel_idle_en << 2)) |
| << 24; |
| clrsetbits_le32(&denali_phy[6], 0x7 << 24, reg_value); |
| clrsetbits_le32(&denali_phy[134], 0x7 << 24, reg_value); |
| clrsetbits_le32(&denali_phy[262], 0x7 << 24, reg_value); |
| clrsetbits_le32(&denali_phy[390], 0x7 << 24, reg_value); |
| |
| /* phy_adr_tsel_enable_ 1bit DENALI_PHY_518/646/774 offset_8 */ |
| reg_value = tsel_wr_en << 8; |
| clrsetbits_le32(&denali_phy[518], 0x1 << 8, reg_value); |
| clrsetbits_le32(&denali_phy[646], 0x1 << 8, reg_value); |
| clrsetbits_le32(&denali_phy[774], 0x1 << 8, reg_value); |
| |
| /* phy_pad_addr_term tsel 1bit DENALI_PHY_933 offset_17 */ |
| reg_value = tsel_wr_en << 17; |
| clrsetbits_le32(&denali_phy[933], 0x1 << 17, reg_value); |
| /* |
| * pad_rst/cke/cs/clk_term tsel 1bits |
| * DENALI_PHY_938/936/940/934 offset_17 |
| */ |
| clrsetbits_le32(&denali_phy[938], 0x1 << 17, reg_value); |
| clrsetbits_le32(&denali_phy[936], 0x1 << 17, reg_value); |
| clrsetbits_le32(&denali_phy[940], 0x1 << 17, reg_value); |
| clrsetbits_le32(&denali_phy[934], 0x1 << 17, reg_value); |
| |
| /* phy_pad_fdbk_term 1bit DENALI_PHY_930 offset_17 */ |
| clrsetbits_le32(&denali_phy[930], 0x1 << 17, reg_value); |
| } |
| |
| static int phy_io_config(const struct chan_info *chan, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_phy = chan->publ->denali_phy; |
| u32 vref_mode_dq, vref_value_dq, vref_mode_ac, vref_value_ac; |
| u32 mode_sel; |
| u32 reg_value; |
| u32 drv_value, odt_value; |
| u32 speed; |
| |
| /* vref setting */ |
| if (params->base.dramtype == LPDDR4) { |
| /* LPDDR4 */ |
| vref_mode_dq = 0x6; |
| vref_value_dq = 0x1f; |
| vref_mode_ac = 0x6; |
| vref_value_ac = 0x1f; |
| } else if (params->base.dramtype == LPDDR3) { |
| if (params->base.odt == 1) { |
| vref_mode_dq = 0x5; /* LPDDR3 ODT */ |
| drv_value = (readl(&denali_phy[6]) >> 12) & 0xf; |
| odt_value = (readl(&denali_phy[6]) >> 4) & 0xf; |
| if (drv_value == PHY_DRV_ODT_48) { |
| switch (odt_value) { |
| case PHY_DRV_ODT_240: |
| vref_value_dq = 0x16; |
| break; |
| case PHY_DRV_ODT_120: |
| vref_value_dq = 0x26; |
| break; |
| case PHY_DRV_ODT_60: |
| vref_value_dq = 0x36; |
| break; |
| default: |
| debug("Invalid ODT value.\n"); |
| return -EINVAL; |
| } |
| } else if (drv_value == PHY_DRV_ODT_40) { |
| switch (odt_value) { |
| case PHY_DRV_ODT_240: |
| vref_value_dq = 0x19; |
| break; |
| case PHY_DRV_ODT_120: |
| vref_value_dq = 0x23; |
| break; |
| case PHY_DRV_ODT_60: |
| vref_value_dq = 0x31; |
| break; |
| default: |
| debug("Invalid ODT value.\n"); |
| return -EINVAL; |
| } |
| } else if (drv_value == PHY_DRV_ODT_34_3) { |
| switch (odt_value) { |
| case PHY_DRV_ODT_240: |
| vref_value_dq = 0x17; |
| break; |
| case PHY_DRV_ODT_120: |
| vref_value_dq = 0x20; |
| break; |
| case PHY_DRV_ODT_60: |
| vref_value_dq = 0x2e; |
| break; |
| default: |
| debug("Invalid ODT value.\n"); |
| return -EINVAL; |
| } |
| } else { |
| debug("Invalid DRV value.\n"); |
| return -EINVAL; |
| } |
| } else { |
| vref_mode_dq = 0x2; /* LPDDR3 */ |
| vref_value_dq = 0x1f; |
| } |
| vref_mode_ac = 0x2; |
| vref_value_ac = 0x1f; |
| } else if (params->base.dramtype == DDR3) { |
| /* DDR3L */ |
| vref_mode_dq = 0x1; |
| vref_value_dq = 0x1f; |
| vref_mode_ac = 0x1; |
| vref_value_ac = 0x1f; |
| } else { |
| debug("Unknown DRAM type.\n"); |
| return -EINVAL; |
| } |
| |
| reg_value = (vref_mode_dq << 9) | (0x1 << 8) | vref_value_dq; |
| |
| /* PHY_913 PHY_PAD_VREF_CTRL_DQ_0 12bits offset_8 */ |
| clrsetbits_le32(&denali_phy[913], 0xfff << 8, reg_value << 8); |
| /* PHY_914 PHY_PAD_VREF_CTRL_DQ_1 12bits offset_0 */ |
| clrsetbits_le32(&denali_phy[914], 0xfff, reg_value); |
| /* PHY_914 PHY_PAD_VREF_CTRL_DQ_2 12bits offset_16 */ |
| clrsetbits_le32(&denali_phy[914], 0xfff << 16, reg_value << 16); |
| /* PHY_915 PHY_PAD_VREF_CTRL_DQ_3 12bits offset_0 */ |
| clrsetbits_le32(&denali_phy[915], 0xfff, reg_value); |
| |
| reg_value = (vref_mode_ac << 9) | (0x1 << 8) | vref_value_ac; |
| |
| /* PHY_915 PHY_PAD_VREF_CTRL_AC 12bits offset_16 */ |
| clrsetbits_le32(&denali_phy[915], 0xfff << 16, reg_value << 16); |
| |
| if (params->base.dramtype == LPDDR4) |
| mode_sel = 0x6; |
| else if (params->base.dramtype == LPDDR3) |
| mode_sel = 0x0; |
| else if (params->base.dramtype == DDR3) |
| mode_sel = 0x1; |
| else |
| return -EINVAL; |
| |
| /* PHY_924 PHY_PAD_FDBK_DRIVE */ |
| clrsetbits_le32(&denali_phy[924], 0x7 << 15, mode_sel << 15); |
| /* PHY_926 PHY_PAD_DATA_DRIVE */ |
| clrsetbits_le32(&denali_phy[926], 0x7 << 6, mode_sel << 6); |
| /* PHY_927 PHY_PAD_DQS_DRIVE */ |
| clrsetbits_le32(&denali_phy[927], 0x7 << 6, mode_sel << 6); |
| /* PHY_928 PHY_PAD_ADDR_DRIVE */ |
| clrsetbits_le32(&denali_phy[928], 0x7 << 14, mode_sel << 14); |
| /* PHY_929 PHY_PAD_CLK_DRIVE */ |
| clrsetbits_le32(&denali_phy[929], 0x7 << 14, mode_sel << 14); |
| /* PHY_935 PHY_PAD_CKE_DRIVE */ |
| clrsetbits_le32(&denali_phy[935], 0x7 << 14, mode_sel << 14); |
| /* PHY_937 PHY_PAD_RST_DRIVE */ |
| clrsetbits_le32(&denali_phy[937], 0x7 << 14, mode_sel << 14); |
| /* PHY_939 PHY_PAD_CS_DRIVE */ |
| clrsetbits_le32(&denali_phy[939], 0x7 << 14, mode_sel << 14); |
| |
| /* speed setting */ |
| if (params->base.ddr_freq < 400) |
| speed = 0x0; |
| else if (params->base.ddr_freq < 800) |
| speed = 0x1; |
| else if (params->base.ddr_freq < 1200) |
| speed = 0x2; |
| else |
| speed = 0x3; |
| |
| /* PHY_924 PHY_PAD_FDBK_DRIVE */ |
| clrsetbits_le32(&denali_phy[924], 0x3 << 21, speed << 21); |
| /* PHY_926 PHY_PAD_DATA_DRIVE */ |
| clrsetbits_le32(&denali_phy[926], 0x3 << 9, speed << 9); |
| /* PHY_927 PHY_PAD_DQS_DRIVE */ |
| clrsetbits_le32(&denali_phy[927], 0x3 << 9, speed << 9); |
| /* PHY_928 PHY_PAD_ADDR_DRIVE */ |
| clrsetbits_le32(&denali_phy[928], 0x3 << 17, speed << 17); |
| /* PHY_929 PHY_PAD_CLK_DRIVE */ |
| clrsetbits_le32(&denali_phy[929], 0x3 << 17, speed << 17); |
| /* PHY_935 PHY_PAD_CKE_DRIVE */ |
| clrsetbits_le32(&denali_phy[935], 0x3 << 17, speed << 17); |
| /* PHY_937 PHY_PAD_RST_DRIVE */ |
| clrsetbits_le32(&denali_phy[937], 0x3 << 17, speed << 17); |
| /* PHY_939 PHY_PAD_CS_DRIVE */ |
| clrsetbits_le32(&denali_phy[939], 0x3 << 17, speed << 17); |
| |
| return 0; |
| } |
| |
| static int pctl_cfg(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_ctl = chan->pctl->denali_ctl; |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 *denali_phy = chan->publ->denali_phy; |
| const u32 *params_ctl = params->pctl_regs.denali_ctl; |
| const u32 *params_phy = params->phy_regs.denali_phy; |
| u32 tmp, tmp1, tmp2; |
| u32 pwrup_srefresh_exit; |
| int ret; |
| const ulong timeout_ms = 200; |
| |
| /* |
| * work around controller bug: |
| * Do not program DRAM_CLASS until NO_PHY_IND_TRAIN_INT is programmed |
| */ |
| copy_to_reg(&denali_ctl[1], ¶ms_ctl[1], |
| sizeof(struct rk3399_ddr_pctl_regs) - 4); |
| writel(params_ctl[0], &denali_ctl[0]); |
| |
| copy_to_reg(denali_pi, ¶ms->pi_regs.denali_pi[0], |
| sizeof(struct rk3399_ddr_pi_regs)); |
| |
| /* rank count need to set for init */ |
| set_memory_map(chan, channel, params); |
| |
| writel(params->phy_regs.denali_phy[910], &denali_phy[910]); |
| writel(params->phy_regs.denali_phy[911], &denali_phy[911]); |
| writel(params->phy_regs.denali_phy[912], &denali_phy[912]); |
| |
| pwrup_srefresh_exit = readl(&denali_ctl[68]) & PWRUP_SREFRESH_EXIT; |
| clrbits_le32(&denali_ctl[68], PWRUP_SREFRESH_EXIT); |
| |
| /* PHY_DLL_RST_EN */ |
| clrsetbits_le32(&denali_phy[957], 0x3 << 24, 1 << 24); |
| |
| setbits_le32(&denali_pi[0], START); |
| setbits_le32(&denali_ctl[0], START); |
| |
| /* Waiting for phy DLL lock */ |
| while (1) { |
| tmp = readl(&denali_phy[920]); |
| tmp1 = readl(&denali_phy[921]); |
| tmp2 = readl(&denali_phy[922]); |
| if ((((tmp >> 16) & 0x1) == 0x1) && |
| (((tmp1 >> 16) & 0x1) == 0x1) && |
| (((tmp1 >> 0) & 0x1) == 0x1) && |
| (((tmp2 >> 0) & 0x1) == 0x1)) |
| break; |
| } |
| |
| copy_to_reg(&denali_phy[896], ¶ms_phy[896], (958 - 895) * 4); |
| copy_to_reg(&denali_phy[0], ¶ms_phy[0], (90 - 0 + 1) * 4); |
| copy_to_reg(&denali_phy[128], ¶ms_phy[128], (218 - 128 + 1) * 4); |
| copy_to_reg(&denali_phy[256], ¶ms_phy[256], (346 - 256 + 1) * 4); |
| copy_to_reg(&denali_phy[384], ¶ms_phy[384], (474 - 384 + 1) * 4); |
| copy_to_reg(&denali_phy[512], ¶ms_phy[512], (549 - 512 + 1) * 4); |
| copy_to_reg(&denali_phy[640], ¶ms_phy[640], (677 - 640 + 1) * 4); |
| copy_to_reg(&denali_phy[768], ¶ms_phy[768], (805 - 768 + 1) * 4); |
| set_ds_odt(chan, params); |
| |
| /* |
| * phy_dqs_tsel_wr_timing_X 8bits DENALI_PHY_84/212/340/468 offset_8 |
| * dqs_tsel_wr_end[7:4] add Half cycle |
| */ |
| tmp = (readl(&denali_phy[84]) >> 8) & 0xff; |
| clrsetbits_le32(&denali_phy[84], 0xff << 8, (tmp + 0x10) << 8); |
| tmp = (readl(&denali_phy[212]) >> 8) & 0xff; |
| clrsetbits_le32(&denali_phy[212], 0xff << 8, (tmp + 0x10) << 8); |
| tmp = (readl(&denali_phy[340]) >> 8) & 0xff; |
| clrsetbits_le32(&denali_phy[340], 0xff << 8, (tmp + 0x10) << 8); |
| tmp = (readl(&denali_phy[468]) >> 8) & 0xff; |
| clrsetbits_le32(&denali_phy[468], 0xff << 8, (tmp + 0x10) << 8); |
| |
| /* |
| * phy_dqs_tsel_wr_timing_X 8bits DENALI_PHY_83/211/339/467 offset_8 |
| * dq_tsel_wr_end[7:4] add Half cycle |
| */ |
| tmp = (readl(&denali_phy[83]) >> 16) & 0xff; |
| clrsetbits_le32(&denali_phy[83], 0xff << 16, (tmp + 0x10) << 16); |
| tmp = (readl(&denali_phy[211]) >> 16) & 0xff; |
| clrsetbits_le32(&denali_phy[211], 0xff << 16, (tmp + 0x10) << 16); |
| tmp = (readl(&denali_phy[339]) >> 16) & 0xff; |
| clrsetbits_le32(&denali_phy[339], 0xff << 16, (tmp + 0x10) << 16); |
| tmp = (readl(&denali_phy[467]) >> 16) & 0xff; |
| clrsetbits_le32(&denali_phy[467], 0xff << 16, (tmp + 0x10) << 16); |
| |
| ret = phy_io_config(chan, params); |
| if (ret) |
| return ret; |
| |
| /* PHY_DLL_RST_EN */ |
| clrsetbits_le32(&denali_phy[957], 0x3 << 24, 0x2 << 24); |
| |
| /* Waiting for PHY and DRAM init complete */ |
| tmp = get_timer(0); |
| do { |
| if (get_timer(tmp) > timeout_ms) { |
| pr_err("DRAM (%s): phy failed to lock within %ld ms\n", |
| __func__, timeout_ms); |
| return -ETIME; |
| } |
| } while (!(readl(&denali_ctl[203]) & (1 << 3))); |
| debug("DRAM (%s): phy locked after %ld ms\n", __func__, get_timer(tmp)); |
| |
| clrsetbits_le32(&denali_ctl[68], PWRUP_SREFRESH_EXIT, |
| pwrup_srefresh_exit); |
| return 0; |
| } |
| |
| static void select_per_cs_training_index(const struct chan_info *chan, |
| u32 rank) |
| { |
| u32 *denali_phy = chan->publ->denali_phy; |
| |
| /* PHY_84 PHY_PER_CS_TRAINING_EN_0 1bit offset_16 */ |
| if ((readl(&denali_phy[84]) >> 16) & 1) { |
| /* |
| * PHY_8/136/264/392 |
| * phy_per_cs_training_index_X 1bit offset_24 |
| */ |
| clrsetbits_le32(&denali_phy[8], 0x1 << 24, rank << 24); |
| clrsetbits_le32(&denali_phy[136], 0x1 << 24, rank << 24); |
| clrsetbits_le32(&denali_phy[264], 0x1 << 24, rank << 24); |
| clrsetbits_le32(&denali_phy[392], 0x1 << 24, rank << 24); |
| } |
| } |
| |
| static void override_write_leveling_value(const struct chan_info *chan) |
| { |
| u32 *denali_ctl = chan->pctl->denali_ctl; |
| u32 *denali_phy = chan->publ->denali_phy; |
| u32 byte; |
| |
| /* PHY_896 PHY_FREQ_SEL_MULTICAST_EN 1bit offset_0 */ |
| setbits_le32(&denali_phy[896], 1); |
| |
| /* |
| * PHY_8/136/264/392 |
| * phy_per_cs_training_multicast_en_X 1bit offset_16 |
| */ |
| clrsetbits_le32(&denali_phy[8], 0x1 << 16, 1 << 16); |
| clrsetbits_le32(&denali_phy[136], 0x1 << 16, 1 << 16); |
| clrsetbits_le32(&denali_phy[264], 0x1 << 16, 1 << 16); |
| clrsetbits_le32(&denali_phy[392], 0x1 << 16, 1 << 16); |
| |
| for (byte = 0; byte < 4; byte++) |
| clrsetbits_le32(&denali_phy[63 + (128 * byte)], 0xffff << 16, |
| 0x200 << 16); |
| |
| /* PHY_896 PHY_FREQ_SEL_MULTICAST_EN 1bit offset_0 */ |
| clrbits_le32(&denali_phy[896], 1); |
| |
| /* CTL_200 ctrlupd_req 1bit offset_8 */ |
| clrsetbits_le32(&denali_ctl[200], 0x1 << 8, 0x1 << 8); |
| } |
| |
| static int data_training_ca(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 *denali_phy = chan->publ->denali_phy; |
| u32 i, tmp; |
| u32 obs_0, obs_1, obs_2, obs_err = 0; |
| u32 rank = params->ch[channel].rank; |
| |
| for (i = 0; i < rank; i++) { |
| select_per_cs_training_index(chan, i); |
| |
| /* PI_100 PI_CALVL_EN:RW:8:2 */ |
| clrsetbits_le32(&denali_pi[100], 0x3 << 8, 0x2 << 8); |
| |
| /* PI_92 PI_CALVL_REQ:WR:16:1,PI_CALVL_CS:RW:24:2 */ |
| clrsetbits_le32(&denali_pi[92], |
| (0x1 << 16) | (0x3 << 24), |
| (0x1 << 16) | (i << 24)); |
| |
| /* Waiting for training complete */ |
| while (1) { |
| /* PI_174 PI_INT_STATUS:RD:8:18 */ |
| tmp = readl(&denali_pi[174]) >> 8; |
| /* |
| * check status obs |
| * PHY_532/660/789 phy_adr_calvl_obs1_:0:32 |
| */ |
| obs_0 = readl(&denali_phy[532]); |
| obs_1 = readl(&denali_phy[660]); |
| obs_2 = readl(&denali_phy[788]); |
| if (((obs_0 >> 30) & 0x3) || |
| ((obs_1 >> 30) & 0x3) || |
| ((obs_2 >> 30) & 0x3)) |
| obs_err = 1; |
| if ((((tmp >> 11) & 0x1) == 0x1) && |
| (((tmp >> 13) & 0x1) == 0x1) && |
| (((tmp >> 5) & 0x1) == 0x0) && |
| obs_err == 0) |
| break; |
| else if ((((tmp >> 5) & 0x1) == 0x1) || |
| (obs_err == 1)) |
| return -EIO; |
| } |
| |
| /* clear interrupt,PI_175 PI_INT_ACK:WR:0:17 */ |
| writel(0x00003f7c, (&denali_pi[175])); |
| } |
| |
| clrbits_le32(&denali_pi[100], 0x3 << 8); |
| |
| return 0; |
| } |
| |
| static int data_training_wl(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 *denali_phy = chan->publ->denali_phy; |
| u32 i, tmp; |
| u32 obs_0, obs_1, obs_2, obs_3, obs_err = 0; |
| u32 rank = params->ch[channel].rank; |
| |
| for (i = 0; i < rank; i++) { |
| select_per_cs_training_index(chan, i); |
| |
| /* PI_60 PI_WRLVL_EN:RW:8:2 */ |
| clrsetbits_le32(&denali_pi[60], 0x3 << 8, 0x2 << 8); |
| |
| /* PI_59 PI_WRLVL_REQ:WR:8:1,PI_WRLVL_CS:RW:16:2 */ |
| clrsetbits_le32(&denali_pi[59], |
| (0x1 << 8) | (0x3 << 16), |
| (0x1 << 8) | (i << 16)); |
| |
| /* Waiting for training complete */ |
| while (1) { |
| /* PI_174 PI_INT_STATUS:RD:8:18 */ |
| tmp = readl(&denali_pi[174]) >> 8; |
| |
| /* |
| * check status obs, if error maybe can not |
| * get leveling done PHY_40/168/296/424 |
| * phy_wrlvl_status_obs_X:0:13 |
| */ |
| obs_0 = readl(&denali_phy[40]); |
| obs_1 = readl(&denali_phy[168]); |
| obs_2 = readl(&denali_phy[296]); |
| obs_3 = readl(&denali_phy[424]); |
| if (((obs_0 >> 12) & 0x1) || |
| ((obs_1 >> 12) & 0x1) || |
| ((obs_2 >> 12) & 0x1) || |
| ((obs_3 >> 12) & 0x1)) |
| obs_err = 1; |
| if ((((tmp >> 10) & 0x1) == 0x1) && |
| (((tmp >> 13) & 0x1) == 0x1) && |
| (((tmp >> 4) & 0x1) == 0x0) && |
| obs_err == 0) |
| break; |
| else if ((((tmp >> 4) & 0x1) == 0x1) || |
| (obs_err == 1)) |
| return -EIO; |
| } |
| |
| /* clear interrupt,PI_175 PI_INT_ACK:WR:0:17 */ |
| writel(0x00003f7c, (&denali_pi[175])); |
| } |
| |
| override_write_leveling_value(chan); |
| clrbits_le32(&denali_pi[60], 0x3 << 8); |
| |
| return 0; |
| } |
| |
| static int data_training_rg(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 *denali_phy = chan->publ->denali_phy; |
| u32 i, tmp; |
| u32 obs_0, obs_1, obs_2, obs_3, obs_err = 0; |
| u32 rank = params->ch[channel].rank; |
| |
| for (i = 0; i < rank; i++) { |
| select_per_cs_training_index(chan, i); |
| |
| /* PI_80 PI_RDLVL_GATE_EN:RW:24:2 */ |
| clrsetbits_le32(&denali_pi[80], 0x3 << 24, 0x2 << 24); |
| |
| /* |
| * PI_74 PI_RDLVL_GATE_REQ:WR:16:1 |
| * PI_RDLVL_CS:RW:24:2 |
| */ |
| clrsetbits_le32(&denali_pi[74], |
| (0x1 << 16) | (0x3 << 24), |
| (0x1 << 16) | (i << 24)); |
| |
| /* Waiting for training complete */ |
| while (1) { |
| /* PI_174 PI_INT_STATUS:RD:8:18 */ |
| tmp = readl(&denali_pi[174]) >> 8; |
| |
| /* |
| * check status obs |
| * PHY_43/171/299/427 |
| * PHY_GTLVL_STATUS_OBS_x:16:8 |
| */ |
| obs_0 = readl(&denali_phy[43]); |
| obs_1 = readl(&denali_phy[171]); |
| obs_2 = readl(&denali_phy[299]); |
| obs_3 = readl(&denali_phy[427]); |
| if (((obs_0 >> (16 + 6)) & 0x3) || |
| ((obs_1 >> (16 + 6)) & 0x3) || |
| ((obs_2 >> (16 + 6)) & 0x3) || |
| ((obs_3 >> (16 + 6)) & 0x3)) |
| obs_err = 1; |
| if ((((tmp >> 9) & 0x1) == 0x1) && |
| (((tmp >> 13) & 0x1) == 0x1) && |
| (((tmp >> 3) & 0x1) == 0x0) && |
| obs_err == 0) |
| break; |
| else if ((((tmp >> 3) & 0x1) == 0x1) || |
| (obs_err == 1)) |
| return -EIO; |
| } |
| |
| /* clear interrupt,PI_175 PI_INT_ACK:WR:0:17 */ |
| writel(0x00003f7c, (&denali_pi[175])); |
| } |
| |
| clrbits_le32(&denali_pi[80], 0x3 << 24); |
| |
| return 0; |
| } |
| |
| static int data_training_rl(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 i, tmp; |
| u32 rank = params->ch[channel].rank; |
| |
| for (i = 0; i < rank; i++) { |
| select_per_cs_training_index(chan, i); |
| |
| /* PI_80 PI_RDLVL_EN:RW:16:2 */ |
| clrsetbits_le32(&denali_pi[80], 0x3 << 16, 0x2 << 16); |
| |
| /* PI_74 PI_RDLVL_REQ:WR:8:1,PI_RDLVL_CS:RW:24:2 */ |
| clrsetbits_le32(&denali_pi[74], |
| (0x1 << 8) | (0x3 << 24), |
| (0x1 << 8) | (i << 24)); |
| |
| /* Waiting for training complete */ |
| while (1) { |
| /* PI_174 PI_INT_STATUS:RD:8:18 */ |
| tmp = readl(&denali_pi[174]) >> 8; |
| |
| /* |
| * make sure status obs not report error bit |
| * PHY_46/174/302/430 |
| * phy_rdlvl_status_obs_X:16:8 |
| */ |
| if ((((tmp >> 8) & 0x1) == 0x1) && |
| (((tmp >> 13) & 0x1) == 0x1) && |
| (((tmp >> 2) & 0x1) == 0x0)) |
| break; |
| else if (((tmp >> 2) & 0x1) == 0x1) |
| return -EIO; |
| } |
| |
| /* clear interrupt,PI_175 PI_INT_ACK:WR:0:17 */ |
| writel(0x00003f7c, (&denali_pi[175])); |
| } |
| |
| clrbits_le32(&denali_pi[80], 0x3 << 16); |
| |
| return 0; |
| } |
| |
| static int data_training_wdql(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 *denali_pi = chan->pi->denali_pi; |
| u32 i, tmp; |
| u32 rank = params->ch[channel].rank; |
| |
| for (i = 0; i < rank; i++) { |
| select_per_cs_training_index(chan, i); |
| |
| /* |
| * disable PI_WDQLVL_VREF_EN before wdq leveling? |
| * PI_181 PI_WDQLVL_VREF_EN:RW:8:1 |
| */ |
| clrbits_le32(&denali_pi[181], 0x1 << 8); |
| |
| /* PI_124 PI_WDQLVL_EN:RW:16:2 */ |
| clrsetbits_le32(&denali_pi[124], 0x3 << 16, 0x2 << 16); |
| |
| /* PI_121 PI_WDQLVL_REQ:WR:8:1,PI_WDQLVL_CS:RW:16:2 */ |
| clrsetbits_le32(&denali_pi[121], |
| (0x1 << 8) | (0x3 << 16), |
| (0x1 << 8) | (i << 16)); |
| |
| /* Waiting for training complete */ |
| while (1) { |
| /* PI_174 PI_INT_STATUS:RD:8:18 */ |
| tmp = readl(&denali_pi[174]) >> 8; |
| if ((((tmp >> 12) & 0x1) == 0x1) && |
| (((tmp >> 13) & 0x1) == 0x1) && |
| (((tmp >> 6) & 0x1) == 0x0)) |
| break; |
| else if (((tmp >> 6) & 0x1) == 0x1) |
| return -EIO; |
| } |
| |
| /* clear interrupt,PI_175 PI_INT_ACK:WR:0:17 */ |
| writel(0x00003f7c, (&denali_pi[175])); |
| } |
| |
| clrbits_le32(&denali_pi[124], 0x3 << 16); |
| |
| return 0; |
| } |
| |
| static int data_training(const struct chan_info *chan, u32 channel, |
| const struct rk3399_sdram_params *params, |
| u32 training_flag) |
| { |
| u32 *denali_phy = chan->publ->denali_phy; |
| |
| /* PHY_927 PHY_PAD_DQS_DRIVE RPULL offset_22 */ |
| setbits_le32(&denali_phy[927], (1 << 22)); |
| |
| if (training_flag == PI_FULL_TRAINING) { |
| if (params->base.dramtype == LPDDR4) { |
| training_flag = PI_CA_TRAINING | PI_WRITE_LEVELING | |
| PI_READ_GATE_TRAINING | |
| PI_READ_LEVELING | PI_WDQ_LEVELING; |
| } else if (params->base.dramtype == LPDDR3) { |
| training_flag = PI_CA_TRAINING | PI_WRITE_LEVELING | |
| PI_READ_GATE_TRAINING; |
| } else if (params->base.dramtype == DDR3) { |
| training_flag = PI_WRITE_LEVELING | |
| PI_READ_GATE_TRAINING | |
| PI_READ_LEVELING; |
| } |
| } |
| |
| /* ca training(LPDDR4,LPDDR3 support) */ |
| if ((training_flag & PI_CA_TRAINING) == PI_CA_TRAINING) |
| data_training_ca(chan, channel, params); |
| |
| /* write leveling(LPDDR4,LPDDR3,DDR3 support) */ |
| if ((training_flag & PI_WRITE_LEVELING) == PI_WRITE_LEVELING) |
| data_training_wl(chan, channel, params); |
| |
| /* read gate training(LPDDR4,LPDDR3,DDR3 support) */ |
| if ((training_flag & PI_READ_GATE_TRAINING) == PI_READ_GATE_TRAINING) |
| data_training_rg(chan, channel, params); |
| |
| /* read leveling(LPDDR4,LPDDR3,DDR3 support) */ |
| if ((training_flag & PI_READ_LEVELING) == PI_READ_LEVELING) |
| data_training_rl(chan, channel, params); |
| |
| /* wdq leveling(LPDDR4 support) */ |
| if ((training_flag & PI_WDQ_LEVELING) == PI_WDQ_LEVELING) |
| data_training_wdql(chan, channel, params); |
| |
| /* PHY_927 PHY_PAD_DQS_DRIVE RPULL offset_22 */ |
| clrbits_le32(&denali_phy[927], (1 << 22)); |
| |
| return 0; |
| } |
| |
| static void set_ddrconfig(const struct chan_info *chan, |
| const struct rk3399_sdram_params *params, |
| unsigned char channel, u32 ddrconfig) |
| { |
| /* only need to set ddrconfig */ |
| struct rk3399_msch_regs *ddr_msch_regs = chan->msch; |
| unsigned int cs0_cap = 0; |
| unsigned int cs1_cap = 0; |
| |
| cs0_cap = (1 << (params->ch[channel].cs0_row |
| + params->ch[channel].col |
| + params->ch[channel].bk |
| + params->ch[channel].bw - 20)); |
| if (params->ch[channel].rank > 1) |
| cs1_cap = cs0_cap >> (params->ch[channel].cs0_row |
| - params->ch[channel].cs1_row); |
| if (params->ch[channel].row_3_4) { |
| cs0_cap = cs0_cap * 3 / 4; |
| cs1_cap = cs1_cap * 3 / 4; |
| } |
| |
| writel(ddrconfig | (ddrconfig << 8), &ddr_msch_regs->ddrconf); |
| writel(((cs0_cap / 32) & 0xff) | (((cs1_cap / 32) & 0xff) << 8), |
| &ddr_msch_regs->ddrsize); |
| } |
| |
| static void dram_all_config(struct dram_info *dram, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 sys_reg = 0; |
| unsigned int channel, idx; |
| |
| sys_reg |= params->base.dramtype << SYS_REG_DDRTYPE_SHIFT; |
| sys_reg |= (params->base.num_channels - 1) << SYS_REG_NUM_CH_SHIFT; |
| |
| for (channel = 0, idx = 0; |
| (idx < params->base.num_channels) && (channel < 2); |
| channel++) { |
| const struct rk3399_sdram_channel *info = ¶ms->ch[channel]; |
| struct rk3399_msch_regs *ddr_msch_regs; |
| const struct rk3399_msch_timings *noc_timing; |
| |
| if (params->ch[channel].col == 0) |
| continue; |
| idx++; |
| sys_reg |= info->row_3_4 << SYS_REG_ROW_3_4_SHIFT(channel); |
| sys_reg |= 1 << SYS_REG_CHINFO_SHIFT(channel); |
| sys_reg |= (info->rank - 1) << SYS_REG_RANK_SHIFT(channel); |
| sys_reg |= (info->col - 9) << SYS_REG_COL_SHIFT(channel); |
| sys_reg |= info->bk == 3 ? 0 : 1 << SYS_REG_BK_SHIFT(channel); |
| sys_reg |= (info->cs0_row - 13) << |
| SYS_REG_CS0_ROW_SHIFT(channel); |
| sys_reg |= (info->cs1_row - 13) << |
| SYS_REG_CS1_ROW_SHIFT(channel); |
| sys_reg |= (2 >> info->bw) << SYS_REG_BW_SHIFT(channel); |
| sys_reg |= (2 >> info->dbw) << SYS_REG_DBW_SHIFT(channel); |
| |
| ddr_msch_regs = dram->chan[channel].msch; |
| noc_timing = ¶ms->ch[channel].noc_timings; |
| writel(noc_timing->ddrtiminga0, |
| &ddr_msch_regs->ddrtiminga0); |
| writel(noc_timing->ddrtimingb0, |
| &ddr_msch_regs->ddrtimingb0); |
| writel(noc_timing->ddrtimingc0, |
| &ddr_msch_regs->ddrtimingc0); |
| writel(noc_timing->devtodev0, |
| &ddr_msch_regs->devtodev0); |
| writel(noc_timing->ddrmode, |
| &ddr_msch_regs->ddrmode); |
| |
| /* rank 1 memory clock disable (dfi_dram_clk_disable = 1) */ |
| if (params->ch[channel].rank == 1) |
| setbits_le32(&dram->chan[channel].pctl->denali_ctl[276], |
| 1 << 17); |
| } |
| |
| writel(sys_reg, &dram->pmugrf->os_reg2); |
| rk_clrsetreg(&dram->pmusgrf->soc_con4, 0x1f << 10, |
| params->base.stride << 10); |
| |
| /* reboot hold register set */ |
| writel(PRESET_SGRF_HOLD(0) | PRESET_GPIO0_HOLD(1) | |
| PRESET_GPIO1_HOLD(1), |
| &dram->pmucru->pmucru_rstnhold_con[1]); |
| clrsetbits_le32(&dram->cru->glb_rst_con, 0x3, 0x3); |
| } |
| |
| static int switch_to_phy_index1(struct dram_info *dram, |
| const struct rk3399_sdram_params *params) |
| { |
| u32 channel; |
| u32 *denali_phy; |
| u32 ch_count = params->base.num_channels; |
| int ret; |
| int i = 0; |
| |
| writel(RK_CLRSETBITS(0x03 << 4 | 1 << 2 | 1, |
| 1 << 4 | 1 << 2 | 1), |
| &dram->cic->cic_ctrl0); |
| while (!(readl(&dram->cic->cic_status0) & (1 << 2))) { |
| mdelay(10); |
| i++; |
| if (i > 10) { |
| debug("index1 frequency change overtime\n"); |
| return -ETIME; |
| } |
| } |
| |
| i = 0; |
| writel(RK_CLRSETBITS(1 << 1, 1 << 1), &dram->cic->cic_ctrl0); |
| while (!(readl(&dram->cic->cic_status0) & (1 << 0))) { |
| mdelay(10); |
| i++; |
| if (i > 10) { |
| debug("index1 frequency done overtime\n"); |
| return -ETIME; |
| } |
| } |
| |
| for (channel = 0; channel < ch_count; channel++) { |
| denali_phy = dram->chan[channel].publ->denali_phy; |
| clrsetbits_le32(&denali_phy[896], (0x3 << 8) | 1, 1 << 8); |
| ret = data_training(&dram->chan[channel], channel, |
| params, PI_FULL_TRAINING); |
| if (ret) { |
| debug("index1 training failed\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int sdram_init(struct dram_info *dram, |
| const struct rk3399_sdram_params *params) |
| { |
| unsigned char dramtype = params->base.dramtype; |
| unsigned int ddr_freq = params->base.ddr_freq; |
| int channel; |
| int ret; |
| |
| debug("Starting SDRAM initialization...\n"); |
| |
| if ((dramtype == DDR3 && ddr_freq > 933) || |
| (dramtype == LPDDR3 && ddr_freq > 933) || |
| (dramtype == LPDDR4 && ddr_freq > 800)) { |
| debug("SDRAM frequency is to high!"); |
| return -E2BIG; |
| } |
| |
| for (channel = 0; channel < 2; channel++) { |
| const struct chan_info *chan = &dram->chan[channel]; |
| struct rk3399_ddr_publ_regs *publ = chan->publ; |
| |
| phy_dll_bypass_set(publ, ddr_freq); |
| |
| if (channel >= params->base.num_channels) |
| continue; |
| |
| ret = pctl_cfg(chan, channel, params); |
| if (ret < 0) { |
| printf("%s: pctl config failed\n", __func__); |
| return ret; |
| } |
| |
| /* LPDDR2/LPDDR3 need to wait DAI complete, max 10us */ |
| if (dramtype == LPDDR3) |
| udelay(10); |
| |
| if (data_training(chan, channel, params, PI_FULL_TRAINING)) { |
| printf("SDRAM initialization failed, reset\n"); |
| return -EIO; |
| } |
| |
| set_ddrconfig(chan, params, channel, |
| params->ch[channel].ddrconfig); |
| } |
| dram_all_config(dram, params); |
| switch_to_phy_index1(dram, params); |
| |
| debug("Finish SDRAM initialization...\n"); |
| return 0; |
| } |
| |
| static int rk3399_dmc_ofdata_to_platdata(struct udevice *dev) |
| { |
| #if !CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct rockchip_dmc_plat *plat = dev_get_platdata(dev); |
| int ret; |
| |
| ret = dev_read_u32_array(dev, "rockchip,sdram-params", |
| (u32 *)&plat->sdram_params, |
| sizeof(plat->sdram_params) / sizeof(u32)); |
| if (ret) { |
| printf("%s: Cannot read rockchip,sdram-params %d\n", |
| __func__, ret); |
| return ret; |
| } |
| ret = regmap_init_mem(dev_ofnode(dev), &plat->map); |
| if (ret) |
| printf("%s: regmap failed %d\n", __func__, ret); |
| |
| #endif |
| return 0; |
| } |
| |
| #if CONFIG_IS_ENABLED(OF_PLATDATA) |
| static int conv_of_platdata(struct udevice *dev) |
| { |
| struct rockchip_dmc_plat *plat = dev_get_platdata(dev); |
| struct dtd_rockchip_rk3399_dmc *dtplat = &plat->dtplat; |
| int ret; |
| |
| ret = regmap_init_mem_platdata(dev, dtplat->reg, |
| ARRAY_SIZE(dtplat->reg) / 2, |
| &plat->map); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| #endif |
| |
| static int rk3399_dmc_init(struct udevice *dev) |
| { |
| struct dram_info *priv = dev_get_priv(dev); |
| struct rockchip_dmc_plat *plat = dev_get_platdata(dev); |
| int ret; |
| #if !CONFIG_IS_ENABLED(OF_PLATDATA) |
| struct rk3399_sdram_params *params = &plat->sdram_params; |
| #else |
| struct dtd_rockchip_rk3399_dmc *dtplat = &plat->dtplat; |
| struct rk3399_sdram_params *params = |
| (void *)dtplat->rockchip_sdram_params; |
| |
| ret = conv_of_platdata(dev); |
| if (ret) |
| return ret; |
| #endif |
| |
| priv->cic = syscon_get_first_range(ROCKCHIP_SYSCON_CIC); |
| priv->pmugrf = syscon_get_first_range(ROCKCHIP_SYSCON_PMUGRF); |
| priv->pmusgrf = syscon_get_first_range(ROCKCHIP_SYSCON_PMUSGRF); |
| priv->pmucru = rockchip_get_pmucru(); |
| priv->cru = rockchip_get_cru(); |
| priv->chan[0].pctl = regmap_get_range(plat->map, 0); |
| priv->chan[0].pi = regmap_get_range(plat->map, 1); |
| priv->chan[0].publ = regmap_get_range(plat->map, 2); |
| priv->chan[0].msch = regmap_get_range(plat->map, 3); |
| priv->chan[1].pctl = regmap_get_range(plat->map, 4); |
| priv->chan[1].pi = regmap_get_range(plat->map, 5); |
| priv->chan[1].publ = regmap_get_range(plat->map, 6); |
| priv->chan[1].msch = regmap_get_range(plat->map, 7); |
| |
| debug("con reg %p %p %p %p %p %p %p %p\n", |
| priv->chan[0].pctl, priv->chan[0].pi, |
| priv->chan[0].publ, priv->chan[0].msch, |
| priv->chan[1].pctl, priv->chan[1].pi, |
| priv->chan[1].publ, priv->chan[1].msch); |
| debug("cru %p, cic %p, grf %p, sgrf %p, pmucru %p\n", priv->cru, |
| priv->cic, priv->pmugrf, priv->pmusgrf, priv->pmucru); |
| |
| #if CONFIG_IS_ENABLED(OF_PLATDATA) |
| ret = clk_get_by_index_platdata(dev, 0, dtplat->clocks, &priv->ddr_clk); |
| #else |
| ret = clk_get_by_index(dev, 0, &priv->ddr_clk); |
| #endif |
| if (ret) { |
| printf("%s clk get failed %d\n", __func__, ret); |
| return ret; |
| } |
| |
| ret = clk_set_rate(&priv->ddr_clk, params->base.ddr_freq * MHz); |
| if (ret < 0) { |
| printf("%s clk set failed %d\n", __func__, ret); |
| return ret; |
| } |
| |
| ret = sdram_init(priv, params); |
| if (ret < 0) { |
| printf("%s DRAM init failed %d\n", __func__, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| static int rk3399_dmc_probe(struct udevice *dev) |
| { |
| #if defined(CONFIG_TPL_BUILD) || \ |
| (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD)) |
| if (rk3399_dmc_init(dev)) |
| return 0; |
| #else |
| struct dram_info *priv = dev_get_priv(dev); |
| |
| priv->pmugrf = syscon_get_first_range(ROCKCHIP_SYSCON_PMUGRF); |
| debug("%s: pmugrf = %p\n", __func__, priv->pmugrf); |
| priv->info.base = CONFIG_SYS_SDRAM_BASE; |
| priv->info.size = |
| rockchip_sdram_size((phys_addr_t)&priv->pmugrf->os_reg2); |
| #endif |
| return 0; |
| } |
| |
| static int rk3399_dmc_get_info(struct udevice *dev, struct ram_info *info) |
| { |
| struct dram_info *priv = dev_get_priv(dev); |
| |
| *info = priv->info; |
| |
| return 0; |
| } |
| |
| static struct ram_ops rk3399_dmc_ops = { |
| .get_info = rk3399_dmc_get_info, |
| }; |
| |
| static const struct udevice_id rk3399_dmc_ids[] = { |
| { .compatible = "rockchip,rk3399-dmc" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(dmc_rk3399) = { |
| .name = "rockchip_rk3399_dmc", |
| .id = UCLASS_RAM, |
| .of_match = rk3399_dmc_ids, |
| .ops = &rk3399_dmc_ops, |
| #if defined(CONFIG_TPL_BUILD) || \ |
| (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD)) |
| .ofdata_to_platdata = rk3399_dmc_ofdata_to_platdata, |
| #endif |
| .probe = rk3399_dmc_probe, |
| .priv_auto_alloc_size = sizeof(struct dram_info), |
| #if defined(CONFIG_TPL_BUILD) || \ |
| (!defined(CONFIG_TPL) && defined(CONFIG_SPL_BUILD)) |
| .platdata_auto_alloc_size = sizeof(struct rockchip_dmc_plat), |
| #endif |
| }; |