| /* |
| * ueberarbeitet durch Christoph Seyfert |
| * |
| * (C) Copyright 2004-2005 DENX Software Engineering, |
| * Wolfgang Grandegger <wg@denx.de> |
| * (C) Copyright 2003 |
| * DAVE Srl |
| * |
| * http://www.dave-tech.it |
| * http://www.wawnet.biz |
| * mailto:info@wawnet.biz |
| * |
| * Credits: Stefan Roese, Wolfgang Denk |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */ |
| #define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */ |
| #define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */ |
| #ifndef CONFIG_PPCHAMELEON_MODULE_MODEL |
| #define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA |
| #endif |
| |
| /* Only one of the following two symbols must be defined (default is 25 MHz) |
| * CONFIG_PPCHAMELEON_CLK_25 |
| * CONFIG_PPCHAMELEON_CLK_33 |
| */ |
| #if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) |
| #define CONFIG_PPCHAMELEON_CLK_25 |
| #endif |
| |
| #if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) |
| #error "* Two external frequencies (SysClk) are defined! *" |
| #endif |
| |
| #undef CONFIG_PPCHAMELEON_SMI712 |
| |
| /* |
| * Debug stuff |
| */ |
| #undef __DEBUG_START_FROM_SRAM__ |
| #define __DISABLE_MACHINE_EXCEPTION__ |
| |
| #ifdef __DEBUG_START_FROM_SRAM__ |
| #define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4 |
| #endif |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_405EP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_4xx 1 /* ...member of PPC4xx family */ |
| #define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */ |
| #define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds" |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ |
| |
| #ifdef CONFIG_PPCHAMELEON_CLK_25 |
| # define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ |
| #elif (defined (CONFIG_PPCHAMELEON_CLK_33)) |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| #else |
| # error "* External frequency (SysClk) not defined! *" |
| #endif |
| |
| #define CONFIG_CONS_INDEX 2 /* Use UART1 */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| #define CONFIG_VERSION_VARIABLE 1 /* add version variable */ |
| #define CONFIG_IDENT_STRING "1" |
| |
| #undef CONFIG_BOOTARGS |
| |
| /* Ethernet stuff */ |
| #define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ |
| #define CONFIG_ETHADDR 00:50:C2:1E:AF:FE |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| |
| #define CONFIG_PPC4xx_EMAC |
| #undef CONFIG_EXT_PHY |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #ifndef CONFIG_EXT_PHY |
| #define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */ |
| #define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */ |
| #else |
| #define CONFIG_PHY_ADDR 2 /* PHY address */ |
| #endif |
| #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ |
| |
| #define CONFIG_TIMESTAMP /* Print image info with timestamp */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_SNTP |
| |
| |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ |
| #define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ |
| |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ |
| |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* The following table includes the supported baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ |
| 57600, 115200, 230400, 460800, 921600 } |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| |
| /*----------------------------------------------------------------------- |
| * NAND-FLASH stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_NAND0_BASE 0xFF400000 |
| #define CONFIG_SYS_NAND1_BASE 0xFF000000 |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE } |
| #define NAND_BIG_DELAY_US 25 |
| |
| /* For CATcenter there is only NAND on the module */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ |
| #define NAND_NO_RB |
| |
| #define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */ |
| #define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ |
| #define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ |
| #define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ |
| |
| #define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */ |
| #define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */ |
| #define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ |
| #define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ |
| |
| |
| #define MACRO_NAND_DISABLE_CE(nandptr) do \ |
| { \ |
| switch((unsigned long)nandptr) \ |
| { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #define MACRO_NAND_ENABLE_CE(nandptr) do \ |
| { \ |
| switch((unsigned long)nandptr) \ |
| { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #define MACRO_NAND_CTL_CLRALE(nandptr) do \ |
| { \ |
| switch((unsigned long)nandptr) \ |
| { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #define MACRO_NAND_CTL_SETALE(nandptr) do \ |
| { \ |
| switch((unsigned long)nandptr) \ |
| { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #define MACRO_NAND_CTL_CLRCLE(nandptr) do \ |
| { \ |
| switch((unsigned long)nandptr) \ |
| { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #define MACRO_NAND_CTL_SETCLE(nandptr) do { \ |
| switch((unsigned long)nandptr) { \ |
| case CONFIG_SYS_NAND0_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \ |
| break; \ |
| case CONFIG_SYS_NAND1_BASE: \ |
| out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \ |
| break; \ |
| } \ |
| } while(0) |
| |
| #ifdef NAND_NO_RB |
| /* constant delay (see also tR in the datasheet) */ |
| #define NAND_WAIT_READY(nand) do { \ |
| udelay(12); \ |
| } while (0) |
| #else |
| /* use the R/B pin */ |
| /* TBD */ |
| #endif |
| |
| #define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) |
| #define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) |
| #define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) |
| #define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #if 0 /* No PCI on CATcenter */ |
| #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ |
| #undef CONFIG_PCI_PNP /* do pci plug-and-play */ |
| /* resource configuration */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ |
| #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ |
| |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ |
| #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ |
| #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ |
| #endif /* No PCI */ |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xFFFC0000 |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ |
| #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ |
| #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ |
| /* |
| * The following defines are added for buggy IOP480 byte interface. |
| * All other boards should use the standard values (CPCI405 etc.) |
| */ |
| #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ |
| #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ |
| #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| /*----------------------------------------------------------------------- |
| * Environment Variable setup |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ |
| #define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ |
| #define CONFIG_ENV_ADDR_REDUND 0xFFFFA000 |
| #define CONFIG_ENV_SIZE_REDUND 0x2000 |
| |
| #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ |
| |
| #define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ |
| #define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ |
| |
| /*----------------------------------------------------------------------- |
| * I2C EEPROM (CAT24WC16) for environment |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| /*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ |
| /* 16 byte page write mode using*/ |
| /* last 4 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0/1 and OR0/1 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ |
| |
| /* Memory Bank 1 (External SRAM) initialization */ |
| /* Since this must replace NOR Flash, we use the same settings for CS0 */ |
| #define CONFIG_SYS_EBC_PB1AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */ |
| |
| /* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ |
| |
| #ifdef CONFIG_PPCHAMELEON_SMI712 |
| /* |
| * Video console (graphic: SMI LynxEM) |
| */ |
| #define CONFIG_VIDEO |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_SMI_LYNXEM |
| #define CONFIG_VIDEO_LOGO |
| /*#define CONFIG_VIDEO_BMP_LOGO*/ |
| #define CONFIG_CONSOLE_EXTRA_INFO |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| /* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ |
| #define CONFIG_SYS_ISA_IO 0xE8000000 |
| /* see also drivers/video/videomodes.c */ |
| #define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303 |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * FPGA stuff |
| */ |
| /* FPGA internal regs */ |
| #define CONFIG_SYS_FPGA_MODE 0x00 |
| #define CONFIG_SYS_FPGA_STATUS 0x02 |
| #define CONFIG_SYS_FPGA_TS 0x04 |
| #define CONFIG_SYS_FPGA_TS_LOW 0x06 |
| #define CONFIG_SYS_FPGA_TS_CAP0 0x10 |
| #define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 |
| #define CONFIG_SYS_FPGA_TS_CAP1 0x14 |
| #define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 |
| #define CONFIG_SYS_FPGA_TS_CAP2 0x18 |
| #define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a |
| #define CONFIG_SYS_FPGA_TS_CAP3 0x1c |
| #define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e |
| |
| /* FPGA Mode Reg */ |
| #define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 |
| #define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 |
| #define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 |
| #define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 |
| |
| /* FPGA Status Reg */ |
| #define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 |
| #define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 |
| #define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 |
| #define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 |
| #define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 |
| |
| #define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ |
| #define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ |
| |
| /* FPGA program pin configuration */ |
| #define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ |
| #define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ |
| #define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for GPIO setup (PPC405EP specific) |
| * |
| * GPIO0[0] - External Bus Controller BLAST output |
| * GPIO0[1-9] - Instruction trace outputs -> GPIO |
| * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs |
| * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO |
| * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs |
| * GPIO0[24-27] - UART0 control signal inputs/outputs |
| * GPIO0[28-29] - UART1 data signal input/output |
| * GPIO0[30] - EMAC0 input |
| * GPIO0[31] - EMAC1 reject packet as output |
| */ |
| #define CONFIG_SYS_GPIO0_OSRL 0x40000550 |
| #define CONFIG_SYS_GPIO0_OSRH 0x00000110 |
| #define CONFIG_SYS_GPIO0_ISR1L 0x00000000 |
| /*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ |
| #define CONFIG_SYS_GPIO0_ISR1H 0x15555444 |
| #define CONFIG_SYS_GPIO0_TSRL 0x00000000 |
| #define CONFIG_SYS_GPIO0_TSRH 0x00000000 |
| #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 |
| |
| #define CONFIG_NO_SERIAL_EEPROM |
| |
| /*--------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_NO_SERIAL_EEPROM |
| |
| /* |
| !----------------------------------------------------------------------- |
| ! Defines for entry options. |
| ! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that |
| ! are plugged in the board will be utilized as non-ECC DIMMs. |
| !----------------------------------------------------------------------- |
| */ |
| #undef AUTO_MEMORY_CONFIG |
| #define DIMM_READ_ADDR 0xAB |
| #define DIMM_WRITE_ADDR 0xAA |
| |
| /* Defines for CPC0_PLLMR1 Register fields */ |
| #define PLL_ACTIVE 0x80000000 |
| #define CPC0_PLLMR1_SSCS 0x80000000 |
| #define PLL_RESET 0x40000000 |
| #define CPC0_PLLMR1_PLLR 0x40000000 |
| /* Feedback multiplier */ |
| #define PLL_FBKDIV 0x00F00000 |
| #define CPC0_PLLMR1_FBDV 0x00F00000 |
| #define PLL_FBKDIV_16 0x00000000 |
| #define PLL_FBKDIV_1 0x00100000 |
| #define PLL_FBKDIV_2 0x00200000 |
| #define PLL_FBKDIV_3 0x00300000 |
| #define PLL_FBKDIV_4 0x00400000 |
| #define PLL_FBKDIV_5 0x00500000 |
| #define PLL_FBKDIV_6 0x00600000 |
| #define PLL_FBKDIV_7 0x00700000 |
| #define PLL_FBKDIV_8 0x00800000 |
| #define PLL_FBKDIV_9 0x00900000 |
| #define PLL_FBKDIV_10 0x00A00000 |
| #define PLL_FBKDIV_11 0x00B00000 |
| #define PLL_FBKDIV_12 0x00C00000 |
| #define PLL_FBKDIV_13 0x00D00000 |
| #define PLL_FBKDIV_14 0x00E00000 |
| #define PLL_FBKDIV_15 0x00F00000 |
| /* Forward A divisor */ |
| #define PLL_FWDDIVA 0x00070000 |
| #define CPC0_PLLMR1_FWDVA 0x00070000 |
| #define PLL_FWDDIVA_8 0x00000000 |
| #define PLL_FWDDIVA_7 0x00010000 |
| #define PLL_FWDDIVA_6 0x00020000 |
| #define PLL_FWDDIVA_5 0x00030000 |
| #define PLL_FWDDIVA_4 0x00040000 |
| #define PLL_FWDDIVA_3 0x00050000 |
| #define PLL_FWDDIVA_2 0x00060000 |
| #define PLL_FWDDIVA_1 0x00070000 |
| /* Forward B divisor */ |
| #define PLL_FWDDIVB 0x00007000 |
| #define CPC0_PLLMR1_FWDVB 0x00007000 |
| #define PLL_FWDDIVB_8 0x00000000 |
| #define PLL_FWDDIVB_7 0x00001000 |
| #define PLL_FWDDIVB_6 0x00002000 |
| #define PLL_FWDDIVB_5 0x00003000 |
| #define PLL_FWDDIVB_4 0x00004000 |
| #define PLL_FWDDIVB_3 0x00005000 |
| #define PLL_FWDDIVB_2 0x00006000 |
| #define PLL_FWDDIVB_1 0x00007000 |
| /* PLL tune bits */ |
| #define PLL_TUNE_MASK 0x000003FF |
| #define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ |
| #define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ |
| #define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ |
| #define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ |
| #define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ |
| #define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ |
| #define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ |
| |
| /* Defines for CPC0_PLLMR0 Register fields */ |
| /* CPU divisor */ |
| #define PLL_CPUDIV 0x00300000 |
| #define CPC0_PLLMR0_CCDV 0x00300000 |
| #define PLL_CPUDIV_1 0x00000000 |
| #define PLL_CPUDIV_2 0x00100000 |
| #define PLL_CPUDIV_3 0x00200000 |
| #define PLL_CPUDIV_4 0x00300000 |
| /* PLB divisor */ |
| #define PLL_PLBDIV 0x00030000 |
| #define CPC0_PLLMR0_CBDV 0x00030000 |
| #define PLL_PLBDIV_1 0x00000000 |
| #define PLL_PLBDIV_2 0x00010000 |
| #define PLL_PLBDIV_3 0x00020000 |
| #define PLL_PLBDIV_4 0x00030000 |
| /* OPB divisor */ |
| #define PLL_OPBDIV 0x00003000 |
| #define CPC0_PLLMR0_OPDV 0x00003000 |
| #define PLL_OPBDIV_1 0x00000000 |
| #define PLL_OPBDIV_2 0x00001000 |
| #define PLL_OPBDIV_3 0x00002000 |
| #define PLL_OPBDIV_4 0x00003000 |
| /* EBC divisor */ |
| #define PLL_EXTBUSDIV 0x00000300 |
| #define CPC0_PLLMR0_EPDV 0x00000300 |
| #define PLL_EXTBUSDIV_2 0x00000000 |
| #define PLL_EXTBUSDIV_3 0x00000100 |
| #define PLL_EXTBUSDIV_4 0x00000200 |
| #define PLL_EXTBUSDIV_5 0x00000300 |
| /* MAL divisor */ |
| #define PLL_MALDIV 0x00000030 |
| #define CPC0_PLLMR0_MPDV 0x00000030 |
| #define PLL_MALDIV_1 0x00000000 |
| #define PLL_MALDIV_2 0x00000010 |
| #define PLL_MALDIV_3 0x00000020 |
| #define PLL_MALDIV_4 0x00000030 |
| /* PCI divisor */ |
| #define PLL_PCIDIV 0x00000003 |
| #define CPC0_PLLMR0_PPFD 0x00000003 |
| #define PLL_PCIDIV_1 0x00000000 |
| #define PLL_PCIDIV_2 0x00000001 |
| #define PLL_PCIDIV_3 0x00000002 |
| #define PLL_PCIDIV_4 0x00000003 |
| |
| #ifdef CONFIG_PPCHAMELEON_CLK_25 |
| /* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ |
| #define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ |
| PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ |
| PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_2) |
| #define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) |
| |
| #elif (defined (CONFIG_PPCHAMELEON_CLK_33)) |
| |
| /* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ |
| #define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ |
| PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ |
| PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_4) |
| #define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) |
| |
| #define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ |
| PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ |
| PLL_MALDIV_1 | PLL_PCIDIV_2) |
| #define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ |
| PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ |
| PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) |
| |
| #else |
| #error "* External frequency (SysClk) not defined! *" |
| #endif |
| |
| #if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) |
| /* Model HI */ |
| #define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 |
| #define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 |
| #define CONFIG_SYS_OPB_FREQ 55555555 |
| /* Model ME */ |
| #elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) |
| #define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 |
| #define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 |
| #define CONFIG_SYS_OPB_FREQ 66666666 |
| #else |
| /* Model BA (default) */ |
| #define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 |
| #define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 |
| #define CONFIG_SYS_OPB_FREQ 66666666 |
| #endif |
| |
| #endif /* CONFIG_NO_SERIAL_EEPROM */ |
| |
| #define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ |
| #define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ |
| |
| /* |
| * JFFS2 partitions |
| * |
| */ |
| /* No command line, one static partition */ |
| #undef CONFIG_CMD_MTDPARTS |
| #define CONFIG_JFFS2_DEV "nand" |
| #define CONFIG_JFFS2_PART_SIZE 0x00200000 |
| #define CONFIG_JFFS2_PART_OFFSET 0x00000000 |
| |
| /* mtdparts command line support |
| * |
| * Note: fake mtd_id used, no linux mtd map file |
| */ |
| /* |
| #define CONFIG_CMD_MTDPARTS |
| #define MTDIDS_DEFAULT "nand0=catcenter" |
| #define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)" |
| */ |
| |
| #endif /* __CONFIG_H */ |