| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Rockchip USBDP Combo PHY with Samsung IP block driver |
| * |
| * Copyright (C) 2021 Rockchip Electronics Co., Ltd |
| */ |
| |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <dm/device_compat.h> |
| #include <dm/devres.h> |
| #include <dm/lists.h> |
| #include <dm/of.h> |
| #include <dm/of_access.h> |
| #include <generic-phy.h> |
| #include <linux/bitfield.h> |
| #include <linux/usb/ch9.h> |
| #include <linux/usb/otg.h> |
| #include <regmap.h> |
| #include <reset.h> |
| #include <syscon.h> |
| #include <asm/arch-rockchip/clock.h> |
| |
| #include <linux/usb/phy-rockchip-usbdp.h> |
| |
| #define BIT_WRITEABLE_SHIFT 16 |
| |
| enum { |
| UDPHY_MODE_NONE = 0, |
| UDPHY_MODE_USB = BIT(0), |
| UDPHY_MODE_DP = BIT(1), |
| UDPHY_MODE_DP_USB = BIT(1) | BIT(0), |
| }; |
| |
| struct udphy_grf_reg { |
| unsigned int offset; |
| unsigned int bitend; |
| unsigned int bitstart; |
| unsigned int disable; |
| unsigned int enable; |
| }; |
| |
| /** |
| * struct reg_sequence - An individual write from a sequence of writes. |
| * |
| * @reg: Register address. |
| * @def: Register value. |
| * @delay_us: Delay to be applied after the register write in microseconds |
| * |
| * Register/value pairs for sequences of writes with an optional delay in |
| * microseconds to be applied after each write. |
| */ |
| struct reg_sequence { |
| unsigned int reg; |
| unsigned int def; |
| unsigned int delay_us; |
| }; |
| |
| struct udphy_grf_cfg { |
| /* u2phy-grf */ |
| struct udphy_grf_reg bvalid_phy_con; |
| struct udphy_grf_reg bvalid_grf_con; |
| |
| /* usb-grf */ |
| struct udphy_grf_reg usb3otg0_cfg; |
| struct udphy_grf_reg usb3otg1_cfg; |
| |
| /* usbdpphy-grf */ |
| struct udphy_grf_reg low_pwrn; |
| struct udphy_grf_reg rx_lfps; |
| }; |
| |
| struct rockchip_udphy; |
| |
| struct rockchip_udphy_cfg { |
| /* resets to be requested */ |
| const char * const *rst_list; |
| int num_rsts; |
| |
| struct udphy_grf_cfg grfcfg; |
| int (*combophy_init)(struct rockchip_udphy *udphy); |
| }; |
| |
| struct rockchip_udphy { |
| struct udevice *dev; |
| struct regmap *pma_regmap; |
| struct regmap *u2phygrf; |
| struct regmap *udphygrf; |
| struct regmap *usbgrf; |
| struct regmap *vogrf; |
| |
| /* clocks and rests */ |
| struct reset_ctl *rsts; |
| |
| /* PHY status management */ |
| bool flip; |
| bool mode_change; |
| u8 mode; |
| u8 status; |
| |
| /* utilized for USB */ |
| bool hs; /* flag for high-speed */ |
| |
| /* utilized for DP */ |
| struct gpio_desc *sbu1_dc_gpio; |
| struct gpio_desc *sbu2_dc_gpio; |
| u32 lane_mux_sel[4]; |
| u32 dp_lane_sel[4]; |
| u32 dp_aux_dout_sel; |
| u32 dp_aux_din_sel; |
| int id; |
| |
| /* PHY const config */ |
| const struct rockchip_udphy_cfg *cfgs; |
| }; |
| |
| static const struct reg_sequence rk3588_udphy_24m_refclk_cfg[] = { |
| {0x0090, 0x68}, {0x0094, 0x68}, |
| {0x0128, 0x24}, {0x012c, 0x44}, |
| {0x0130, 0x3f}, {0x0134, 0x44}, |
| {0x015c, 0xa9}, {0x0160, 0x71}, |
| {0x0164, 0x71}, {0x0168, 0xa9}, |
| {0x0174, 0xa9}, {0x0178, 0x71}, |
| {0x017c, 0x71}, {0x0180, 0xa9}, |
| {0x018c, 0x41}, {0x0190, 0x00}, |
| {0x0194, 0x05}, {0x01ac, 0x2a}, |
| {0x01b0, 0x17}, {0x01b4, 0x17}, |
| {0x01b8, 0x2a}, {0x01c8, 0x04}, |
| {0x01cc, 0x08}, {0x01d0, 0x08}, |
| {0x01d4, 0x04}, {0x01d8, 0x20}, |
| {0x01dc, 0x01}, {0x01e0, 0x09}, |
| {0x01e4, 0x03}, {0x01f0, 0x29}, |
| {0x01f4, 0x02}, {0x01f8, 0x02}, |
| {0x01fc, 0x29}, {0x0208, 0x2a}, |
| {0x020c, 0x17}, {0x0210, 0x17}, |
| {0x0214, 0x2a}, {0x0224, 0x20}, |
| {0x03f0, 0x0d}, {0x03f4, 0x09}, |
| {0x03f8, 0x09}, {0x03fc, 0x0d}, |
| {0x0404, 0x0e}, {0x0408, 0x14}, |
| {0x040c, 0x14}, {0x0410, 0x3b}, |
| {0x0ce0, 0x68}, {0x0ce8, 0xd0}, |
| {0x0cf0, 0x87}, {0x0cf8, 0x70}, |
| {0x0d00, 0x70}, {0x0d08, 0xa9}, |
| {0x1ce0, 0x68}, {0x1ce8, 0xd0}, |
| {0x1cf0, 0x87}, {0x1cf8, 0x70}, |
| {0x1d00, 0x70}, {0x1d08, 0xa9}, |
| {0x0a3c, 0xd0}, {0x0a44, 0xd0}, |
| {0x0a48, 0x01}, {0x0a4c, 0x0d}, |
| {0x0a54, 0xe0}, {0x0a5c, 0xe0}, |
| {0x0a64, 0xa8}, {0x1a3c, 0xd0}, |
| {0x1a44, 0xd0}, {0x1a48, 0x01}, |
| {0x1a4c, 0x0d}, {0x1a54, 0xe0}, |
| {0x1a5c, 0xe0}, {0x1a64, 0xa8} |
| }; |
| |
| static const struct reg_sequence rk3588_udphy_init_sequence[] = { |
| {0x0104, 0x44}, {0x0234, 0xE8}, |
| {0x0248, 0x44}, {0x028C, 0x18}, |
| {0x081C, 0xE5}, {0x0878, 0x00}, |
| {0x0994, 0x1C}, {0x0AF0, 0x00}, |
| {0x181C, 0xE5}, {0x1878, 0x00}, |
| {0x1994, 0x1C}, {0x1AF0, 0x00}, |
| {0x0428, 0x60}, {0x0D58, 0x33}, |
| {0x1D58, 0x33}, {0x0990, 0x74}, |
| {0x0D64, 0x17}, {0x08C8, 0x13}, |
| {0x1990, 0x74}, {0x1D64, 0x17}, |
| {0x18C8, 0x13}, {0x0D90, 0x40}, |
| {0x0DA8, 0x40}, {0x0DC0, 0x40}, |
| {0x0DD8, 0x40}, {0x1D90, 0x40}, |
| {0x1DA8, 0x40}, {0x1DC0, 0x40}, |
| {0x1DD8, 0x40}, {0x03C0, 0x30}, |
| {0x03C4, 0x06}, {0x0E10, 0x00}, |
| {0x1E10, 0x00}, {0x043C, 0x0F}, |
| {0x0D2C, 0xFF}, {0x1D2C, 0xFF}, |
| {0x0D34, 0x0F}, {0x1D34, 0x0F}, |
| {0x08FC, 0x2A}, {0x0914, 0x28}, |
| {0x0A30, 0x03}, {0x0E38, 0x05}, |
| {0x0ECC, 0x27}, {0x0ED0, 0x22}, |
| {0x0ED4, 0x26}, {0x18FC, 0x2A}, |
| {0x1914, 0x28}, {0x1A30, 0x03}, |
| {0x1E38, 0x05}, {0x1ECC, 0x27}, |
| {0x1ED0, 0x22}, {0x1ED4, 0x26}, |
| {0x0048, 0x0F}, {0x0060, 0x3C}, |
| {0x0064, 0xF7}, {0x006C, 0x20}, |
| {0x0070, 0x7D}, {0x0074, 0x68}, |
| {0x0AF4, 0x1A}, {0x1AF4, 0x1A}, |
| {0x0440, 0x3F}, {0x10D4, 0x08}, |
| {0x20D4, 0x08}, {0x00D4, 0x30}, |
| {0x0024, 0x6e}, |
| }; |
| |
| static inline int grfreg_write(struct regmap *base, |
| const struct udphy_grf_reg *reg, bool en) |
| { |
| u32 val, mask, tmp; |
| |
| tmp = en ? reg->enable : reg->disable; |
| mask = GENMASK(reg->bitend, reg->bitstart); |
| val = (tmp << reg->bitstart) | (mask << BIT_WRITEABLE_SHIFT); |
| |
| return regmap_write(base, reg->offset, val); |
| } |
| |
| static int __regmap_multi_reg_write(struct regmap *map, |
| const struct reg_sequence *regs, |
| int num_regs) |
| { |
| int i, ret = 0; |
| |
| for (i = 0; i < num_regs; i++) { |
| ret = regmap_write(map, regs[i].reg, regs[i].def); |
| |
| if (regs[i].delay_us) |
| udelay(regs[i].delay_us); |
| } |
| |
| return ret; |
| } |
| |
| static int udphy_clk_init(struct rockchip_udphy *udphy, struct udevice *dev) |
| { |
| return 0; |
| } |
| |
| static int udphy_reset_init(struct rockchip_udphy *udphy, struct udevice *dev) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int idx; |
| int ret; |
| |
| udphy->rsts = devm_kcalloc(dev, cfg->num_rsts, |
| sizeof(*udphy->rsts), GFP_KERNEL); |
| if (!udphy->rsts) |
| return -ENOMEM; |
| |
| for (idx = 0; idx < cfg->num_rsts; idx++) { |
| const char *name = cfg->rst_list[idx]; |
| |
| ret = reset_get_by_name(dev, name, &udphy->rsts[idx]); |
| if (ret) { |
| dev_err(dev, "failed to get %s reset\n", name); |
| goto err; |
| } |
| |
| reset_assert(&udphy->rsts[idx]); |
| } |
| |
| return 0; |
| |
| err: |
| devm_kfree(dev, udphy->rsts); |
| return ret; |
| } |
| |
| static int udphy_get_rst_idx(const char * const *list, int num, char *name) |
| { |
| int idx; |
| |
| for (idx = 0; idx < num; idx++) { |
| if (!strcmp(list[idx], name)) |
| return idx; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int udphy_reset_assert(struct rockchip_udphy *udphy, char *name) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int idx; |
| |
| idx = udphy_get_rst_idx(cfg->rst_list, cfg->num_rsts, name); |
| if (idx < 0) |
| return idx; |
| |
| return reset_assert(&udphy->rsts[idx]); |
| } |
| |
| static int udphy_reset_deassert(struct rockchip_udphy *udphy, char *name) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int idx; |
| |
| idx = udphy_get_rst_idx(cfg->rst_list, cfg->num_rsts, name); |
| if (idx < 0) |
| return idx; |
| |
| return reset_deassert(&udphy->rsts[idx]); |
| } |
| |
| static void udphy_u3_port_disable(struct rockchip_udphy *udphy, u8 disable) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| const struct udphy_grf_reg *preg; |
| |
| preg = udphy->id ? &cfg->grfcfg.usb3otg1_cfg : &cfg->grfcfg.usb3otg0_cfg; |
| grfreg_write(udphy->usbgrf, preg, disable); |
| } |
| |
| __maybe_unused |
| static void udphy_usb_bvalid_enable(struct rockchip_udphy *udphy, u8 enable) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| |
| grfreg_write(udphy->u2phygrf, &cfg->grfcfg.bvalid_phy_con, enable); |
| grfreg_write(udphy->u2phygrf, &cfg->grfcfg.bvalid_grf_con, enable); |
| } |
| |
| /* |
| * In usb/dp combo phy driver, here are 2 ways to mapping lanes. |
| * |
| * 1 Type-C Mapping table (DP_Alt_Mode V1.0b remove ABF pin mapping) |
| * --------------------------------------------------------------------------- |
| * Type-C Pin B11-B10 A2-A3 A11-A10 B2-B3 |
| * PHY Pad ln0(tx/rx) ln1(tx) ln2(tx/rx) ln3(tx) |
| * C/E(Normal) dpln3 dpln2 dpln0 dpln1 |
| * C/E(Flip ) dpln0 dpln1 dpln3 dpln2 |
| * D/F(Normal) usbrx usbtx dpln0 dpln1 |
| * D/F(Flip ) dpln0 dpln1 usbrx usbtx |
| * A(Normal ) dpln3 dpln1 dpln2 dpln0 |
| * A(Flip ) dpln2 dpln0 dpln3 dpln1 |
| * B(Normal ) usbrx usbtx dpln1 dpln0 |
| * B(Flip ) dpln1 dpln0 usbrx usbtx |
| * --------------------------------------------------------------------------- |
| * |
| * 2 Mapping the lanes in dtsi |
| * if all 4 lane assignment for dp function, define rockchip,dp-lane-mux = <x x x x>; |
| * sample as follow: |
| * --------------------------------------------------------------------------- |
| * B11-B10 A2-A3 A11-A10 B2-B3 |
| * rockchip,dp-lane-mux ln0(tx/rx) ln1(tx) ln2(tx/rx) ln3(tx) |
| * <0 1 2 3> dpln0 dpln1 dpln2 dpln3 |
| * <2 3 0 1> dpln2 dpln3 dpln0 dpln1 |
| * --------------------------------------------------------------------------- |
| * if 2 lane for dp function, 2 lane for usb function, define rockchip,dp-lane-mux = <x x>; |
| * sample as follow: |
| * --------------------------------------------------------------------------- |
| * B11-B10 A2-A3 A11-A10 B2-B3 |
| * rockchip,dp-lane-mux ln0(tx/rx) ln1(tx) ln2(tx/rx) ln3(tx) |
| * <0 1> dpln0 dpln1 usbrx usbtx |
| * <2 3> usbrx usbtx dpln0 dpln1 |
| * --------------------------------------------------------------------------- |
| */ |
| |
| __maybe_unused |
| static int upphy_set_typec_default_mapping(struct rockchip_udphy *udphy) |
| { |
| if (udphy->flip) { |
| udphy->dp_lane_sel[0] = 0; |
| udphy->dp_lane_sel[1] = 1; |
| udphy->dp_lane_sel[2] = 3; |
| udphy->dp_lane_sel[3] = 2; |
| udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP; |
| udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP; |
| udphy->lane_mux_sel[2] = PHY_LANE_MUX_USB; |
| udphy->lane_mux_sel[3] = PHY_LANE_MUX_USB; |
| udphy->dp_aux_dout_sel = PHY_AUX_DP_DATA_POL_INVERT; |
| udphy->dp_aux_din_sel = PHY_AUX_DP_DATA_POL_INVERT; |
| } else { |
| udphy->dp_lane_sel[0] = 2; |
| udphy->dp_lane_sel[1] = 3; |
| udphy->dp_lane_sel[2] = 1; |
| udphy->dp_lane_sel[3] = 0; |
| udphy->lane_mux_sel[0] = PHY_LANE_MUX_USB; |
| udphy->lane_mux_sel[1] = PHY_LANE_MUX_USB; |
| udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP; |
| udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP; |
| udphy->dp_aux_dout_sel = PHY_AUX_DP_DATA_POL_NORMAL; |
| udphy->dp_aux_din_sel = PHY_AUX_DP_DATA_POL_NORMAL; |
| } |
| |
| udphy->mode = UDPHY_MODE_DP_USB; |
| |
| return 0; |
| } |
| |
| static int udphy_setup(struct rockchip_udphy *udphy) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int ret = 0; |
| |
| if (cfg->combophy_init) { |
| ret = cfg->combophy_init(udphy); |
| if (ret) |
| dev_err(udphy->dev, "failed to init usbdp combophy\n"); |
| } |
| |
| return ret; |
| } |
| |
| static int udphy_disable(struct rockchip_udphy *udphy) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int i; |
| |
| for (i = 0; i < cfg->num_rsts; i++) |
| reset_assert(&udphy->rsts[i]); |
| |
| return 0; |
| } |
| |
| static int udphy_parse_lane_mux_data(struct rockchip_udphy *udphy, |
| const struct device_node *np) |
| { |
| struct property *prop; |
| int ret, i, len, num_lanes; |
| |
| prop = of_find_property(np, "rockchip,dp-lane-mux", &len); |
| if (!prop) { |
| dev_dbg(udphy->dev, |
| "failed to find dp lane mux, following dp alt mode\n"); |
| udphy->mode = UDPHY_MODE_USB; |
| return 0; |
| } |
| |
| num_lanes = len / sizeof(u32); |
| |
| if (num_lanes != 2 && num_lanes != 4) { |
| dev_err(udphy->dev, "invalid number of lane mux\n"); |
| return -EINVAL; |
| } |
| |
| ret = of_read_u32_array(np, "rockchip,dp-lane-mux", udphy->dp_lane_sel, |
| num_lanes); |
| if (ret) { |
| dev_err(udphy->dev, "get dp lane mux failed\n"); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < num_lanes; i++) { |
| int j; |
| |
| if (udphy->dp_lane_sel[i] > 3) { |
| dev_err(udphy->dev, |
| "lane mux between 0 and 3, exceeding the range\n"); |
| return -EINVAL; |
| } |
| |
| udphy->lane_mux_sel[udphy->dp_lane_sel[i]] = PHY_LANE_MUX_DP; |
| |
| for (j = i + 1; j < num_lanes; j++) { |
| if (udphy->dp_lane_sel[i] == udphy->dp_lane_sel[j]) { |
| dev_err(udphy->dev, |
| "set repeat lane mux value\n"); |
| return -EINVAL; |
| } |
| } |
| } |
| |
| udphy->mode = UDPHY_MODE_DP; |
| if (num_lanes == 2) |
| udphy->mode |= UDPHY_MODE_USB; |
| |
| return 0; |
| } |
| |
| static int udphy_parse_dt(struct rockchip_udphy *udphy, struct udevice *dev) |
| { |
| const struct device_node *np = ofnode_to_np(dev_ofnode(dev)); |
| enum usb_device_speed maximum_speed; |
| int ret; |
| |
| udphy->u2phygrf = syscon_regmap_lookup_by_phandle(dev, |
| "rockchip,u2phy-grf"); |
| if (IS_ERR(udphy->u2phygrf)) { |
| if (PTR_ERR(udphy->u2phygrf) == -ENODEV) { |
| dev_warn(dev, "missing u2phy-grf dt node\n"); |
| udphy->u2phygrf = NULL; |
| } else { |
| return PTR_ERR(udphy->u2phygrf); |
| } |
| } |
| |
| udphy->udphygrf = syscon_regmap_lookup_by_phandle(dev, |
| "rockchip,usbdpphy-grf"); |
| if (IS_ERR(udphy->udphygrf)) { |
| if (PTR_ERR(udphy->udphygrf) == -ENODEV) { |
| dev_warn(dev, "missing usbdpphy-grf dt node\n"); |
| udphy->udphygrf = NULL; |
| } else { |
| return PTR_ERR(udphy->udphygrf); |
| } |
| } |
| |
| udphy->usbgrf = syscon_regmap_lookup_by_phandle(dev, |
| "rockchip,usb-grf"); |
| if (IS_ERR(udphy->usbgrf)) { |
| if (PTR_ERR(udphy->usbgrf) == -ENODEV) { |
| dev_warn(dev, "missing usb-grf dt node\n"); |
| udphy->usbgrf = NULL; |
| } else { |
| return PTR_ERR(udphy->usbgrf); |
| } |
| } |
| |
| udphy->vogrf = syscon_regmap_lookup_by_phandle(dev, "rockchip,vo-grf"); |
| if (IS_ERR(udphy->vogrf)) { |
| if (PTR_ERR(udphy->vogrf) == -ENODEV) { |
| dev_warn(dev, "missing vo-grf dt node\n"); |
| udphy->vogrf = NULL; |
| } else { |
| return PTR_ERR(udphy->vogrf); |
| } |
| } |
| |
| ret = udphy_parse_lane_mux_data(udphy, np); |
| if (ret) |
| return ret; |
| |
| if (dev_read_prop(dev, "maximum-speed", NULL)) { |
| maximum_speed = usb_get_maximum_speed(dev_ofnode(dev)); |
| udphy->hs = maximum_speed <= USB_SPEED_HIGH ? true : false; |
| } |
| |
| ret = udphy_clk_init(udphy, dev); |
| if (ret) |
| return ret; |
| |
| ret = udphy_reset_init(udphy, dev); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int udphy_power_on(struct rockchip_udphy *udphy, u8 mode) |
| { |
| int ret; |
| |
| if (!(udphy->mode & mode)) { |
| dev_info(udphy->dev, "mode 0x%02x is not support\n", mode); |
| return 0; |
| } |
| |
| if (udphy->status == UDPHY_MODE_NONE) { |
| udphy->mode_change = false; |
| ret = udphy_setup(udphy); |
| if (ret) |
| return ret; |
| |
| if (udphy->mode & UDPHY_MODE_USB) |
| udphy_u3_port_disable(udphy, false); |
| } else if (udphy->mode_change) { |
| udphy->mode_change = false; |
| udphy->status = UDPHY_MODE_NONE; |
| if (udphy->mode == UDPHY_MODE_DP) |
| udphy_u3_port_disable(udphy, true); |
| |
| ret = udphy_disable(udphy); |
| if (ret) |
| return ret; |
| ret = udphy_setup(udphy); |
| if (ret) |
| return ret; |
| } |
| |
| udphy->status |= mode; |
| |
| return 0; |
| } |
| |
| static int udphy_power_off(struct rockchip_udphy *udphy, u8 mode) |
| { |
| int ret; |
| |
| if (!(udphy->mode & mode)) { |
| dev_info(udphy->dev, "mode 0x%02x is not supported\n", mode); |
| return 0; |
| } |
| |
| if (!udphy->status) |
| return 0; |
| |
| udphy->status &= ~mode; |
| |
| if (udphy->status == UDPHY_MODE_NONE) { |
| ret = udphy_disable(udphy); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int rockchip_u3phy_init(struct phy *phy) |
| { |
| struct udevice *parent = phy->dev->parent; |
| struct rockchip_udphy *udphy = dev_get_priv(parent); |
| |
| /* DP only or high-speed, disable U3 port */ |
| if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs) { |
| udphy_u3_port_disable(udphy, true); |
| return 0; |
| } |
| |
| return udphy_power_on(udphy, UDPHY_MODE_USB); |
| } |
| |
| static int rockchip_u3phy_exit(struct phy *phy) |
| { |
| struct udevice *parent = phy->dev->parent; |
| struct rockchip_udphy *udphy = dev_get_priv(parent); |
| |
| /* DP only or high-speed */ |
| if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs) |
| return 0; |
| |
| return udphy_power_off(udphy, UDPHY_MODE_USB); |
| } |
| |
| static const struct phy_ops rockchip_u3phy_ops = { |
| .init = rockchip_u3phy_init, |
| .exit = rockchip_u3phy_exit, |
| }; |
| |
| int rockchip_u3phy_uboot_init(void) |
| { |
| struct udevice *udev; |
| struct rockchip_udphy *udphy; |
| int ret; |
| |
| ret = uclass_get_device_by_driver(UCLASS_PHY, |
| DM_DRIVER_GET(rockchip_udphy_u3_port), |
| &udev); |
| if (ret) { |
| pr_err("%s: get u3-port failed: %d\n", __func__, ret); |
| return ret; |
| } |
| |
| /* DP only or high-speed, disable U3 port */ |
| udphy = dev_get_priv(udev->parent); |
| if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs) { |
| udphy_u3_port_disable(udphy, true); |
| return 0; |
| } |
| |
| return udphy_power_on(udphy, UDPHY_MODE_USB); |
| } |
| |
| static int rockchip_udphy_probe(struct udevice *dev) |
| { |
| const struct device_node *np = ofnode_to_np(dev_ofnode(dev)); |
| struct rockchip_udphy *udphy = dev_get_priv(dev); |
| const struct rockchip_udphy_cfg *phy_cfgs; |
| int id, ret; |
| |
| udphy->dev = dev; |
| |
| id = of_alias_get_id(np, "usbdp"); |
| if (id < 0) |
| id = 0; |
| udphy->id = id; |
| |
| phy_cfgs = (const struct rockchip_udphy_cfg *)dev_get_driver_data(dev); |
| if (!phy_cfgs) { |
| dev_err(dev, "unable to get phy_cfgs\n"); |
| return -EINVAL; |
| } |
| udphy->cfgs = phy_cfgs; |
| |
| ret = regmap_init_mem(dev_ofnode(dev), &udphy->pma_regmap); |
| if (ret) |
| return ret; |
| udphy->pma_regmap->ranges[0].start += UDPHY_PMA; |
| |
| ret = udphy_parse_dt(udphy, dev); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int rockchip_udphy_bind(struct udevice *parent) |
| { |
| struct udevice *child; |
| ofnode subnode; |
| const char *node_name; |
| int ret; |
| |
| dev_for_each_subnode(subnode, parent) { |
| if (!ofnode_valid(subnode)) { |
| printf("%s: no subnode for %s", __func__, parent->name); |
| return -ENXIO; |
| } |
| |
| node_name = ofnode_get_name(subnode); |
| debug("%s: subnode %s\n", __func__, node_name); |
| |
| /* if there is no match, continue */ |
| if (strcasecmp(node_name, "usb3-port")) |
| continue; |
| |
| /* node name is usb3-port */ |
| ret = device_bind_driver_to_node(parent, |
| "rockchip_udphy_u3_port", |
| node_name, subnode, &child); |
| if (ret) { |
| printf("%s: '%s' cannot bind its driver\n", |
| __func__, node_name); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int rk3588_udphy_refclk_set(struct rockchip_udphy *udphy) |
| { |
| /* configure phy reference clock */ |
| return __regmap_multi_reg_write(udphy->pma_regmap, |
| rk3588_udphy_24m_refclk_cfg, |
| ARRAY_SIZE(rk3588_udphy_24m_refclk_cfg)); |
| } |
| |
| static int rk3588_udphy_status_check(struct rockchip_udphy *udphy) |
| { |
| unsigned int val; |
| int ret; |
| |
| if (!(udphy->mode & UDPHY_MODE_USB)) |
| return 0; |
| |
| /* LCPLL check */ |
| ret = regmap_read_poll_timeout(udphy->pma_regmap, |
| CMN_ANA_LCPLL_DONE_OFFSET, |
| val, (val & CMN_ANA_LCPLL_AFC_DONE) && |
| (val & CMN_ANA_LCPLL_LOCK_DONE), |
| 200, 100); |
| if (ret) { |
| dev_err(udphy->dev, "cmn ana lcpll lock timeout\n"); |
| return ret; |
| } |
| |
| if (!udphy->flip) { |
| ret = regmap_read_poll_timeout(udphy->pma_regmap, |
| TRSV_LN0_MON_RX_CDR_DONE_OFFSET, |
| val, |
| val & TRSV_LN0_MON_RX_CDR_LOCK_DONE, |
| 200, 100); |
| if (ret) |
| dev_err(udphy->dev, "trsv ln0 mon rx cdr lock timeout\n"); |
| } else { |
| ret = regmap_read_poll_timeout(udphy->pma_regmap, |
| TRSV_LN2_MON_RX_CDR_DONE_OFFSET, |
| val, |
| val & TRSV_LN2_MON_RX_CDR_LOCK_DONE, |
| 200, 100); |
| if (ret) |
| dev_err(udphy->dev, "trsv ln2 mon rx cdr lock timeout\n"); |
| } |
| |
| return 0; |
| } |
| |
| static int rk3588_udphy_init(struct rockchip_udphy *udphy) |
| { |
| const struct rockchip_udphy_cfg *cfg = udphy->cfgs; |
| int ret; |
| |
| /* enable rx lfps for usb */ |
| if (udphy->mode & UDPHY_MODE_USB) |
| grfreg_write(udphy->udphygrf, &cfg->grfcfg.rx_lfps, true); |
| |
| /* Step 1: power on pma and deassert apb rstn */ |
| grfreg_write(udphy->udphygrf, &cfg->grfcfg.low_pwrn, true); |
| |
| udphy_reset_deassert(udphy, "pma_apb"); |
| udphy_reset_deassert(udphy, "pcs_apb"); |
| |
| /* Step 2: set init sequence and phy refclk */ |
| ret = __regmap_multi_reg_write(udphy->pma_regmap, |
| rk3588_udphy_init_sequence, |
| ARRAY_SIZE(rk3588_udphy_init_sequence)); |
| if (ret) { |
| dev_err(udphy->dev, "init sequence set error %d\n", ret); |
| goto assert_apb; |
| } |
| |
| ret = rk3588_udphy_refclk_set(udphy); |
| if (ret) { |
| dev_err(udphy->dev, "refclk set error %d\n", ret); |
| goto assert_apb; |
| } |
| |
| /* Step 3: configure lane mux */ |
| regmap_update_bits(udphy->pma_regmap, CMN_LANE_MUX_AND_EN_OFFSET, |
| CMN_DP_LANE_MUX_ALL | CMN_DP_LANE_EN_ALL, |
| FIELD_PREP(CMN_DP_LANE_MUX_N(3), |
| udphy->lane_mux_sel[3]) | |
| FIELD_PREP(CMN_DP_LANE_MUX_N(2), |
| udphy->lane_mux_sel[2]) | |
| FIELD_PREP(CMN_DP_LANE_MUX_N(1), |
| udphy->lane_mux_sel[1]) | |
| FIELD_PREP(CMN_DP_LANE_MUX_N(0), |
| udphy->lane_mux_sel[0]) | |
| FIELD_PREP(CMN_DP_LANE_EN_ALL, 0)); |
| |
| /* Step 4: deassert init rstn and wait for 200ns from datasheet */ |
| if (udphy->mode & UDPHY_MODE_USB) |
| udphy_reset_deassert(udphy, "init"); |
| |
| if (udphy->mode & UDPHY_MODE_DP) { |
| regmap_update_bits(udphy->pma_regmap, CMN_DP_RSTN_OFFSET, |
| CMN_DP_INIT_RSTN, |
| FIELD_PREP(CMN_DP_INIT_RSTN, 0x1)); |
| } |
| |
| udelay(1); |
| |
| /* Step 5: deassert cmn/lane rstn */ |
| if (udphy->mode & UDPHY_MODE_USB) { |
| udphy_reset_deassert(udphy, "cmn"); |
| udphy_reset_deassert(udphy, "lane"); |
| } |
| |
| /* Step 6: wait for lock done of pll */ |
| ret = rk3588_udphy_status_check(udphy); |
| if (ret) |
| goto assert_phy; |
| |
| return 0; |
| |
| assert_phy: |
| udphy_reset_assert(udphy, "init"); |
| udphy_reset_assert(udphy, "cmn"); |
| udphy_reset_assert(udphy, "lane"); |
| |
| assert_apb: |
| udphy_reset_assert(udphy, "pma_apb"); |
| udphy_reset_assert(udphy, "pcs_apb"); |
| |
| return ret; |
| } |
| |
| static const char * const rk3588_udphy_rst_l[] = { |
| "init", "cmn", "lane", "pcs_apb", "pma_apb" |
| }; |
| |
| static const struct rockchip_udphy_cfg rk3588_udphy_cfgs = { |
| .num_rsts = ARRAY_SIZE(rk3588_udphy_rst_l), |
| .rst_list = rk3588_udphy_rst_l, |
| .grfcfg = { |
| /* u2phy-grf */ |
| .bvalid_phy_con = { 0x0008, 1, 0, 0x2, 0x3 }, |
| .bvalid_grf_con = { 0x0010, 3, 2, 0x2, 0x3 }, |
| |
| /* usb-grf */ |
| .usb3otg0_cfg = { 0x001c, 15, 0, 0x1100, 0x0188 }, |
| .usb3otg1_cfg = { 0x0034, 15, 0, 0x1100, 0x0188 }, |
| |
| /* usbdpphy-grf */ |
| .low_pwrn = { 0x0004, 13, 13, 0, 1 }, |
| .rx_lfps = { 0x0004, 14, 14, 0, 1 }, |
| }, |
| .combophy_init = rk3588_udphy_init, |
| }; |
| |
| static const struct udevice_id rockchip_udphy_dt_match[] = { |
| { |
| .compatible = "rockchip,rk3588-usbdp-phy", |
| .data = (ulong)&rk3588_udphy_cfgs |
| }, |
| { /* sentinel */ } |
| }; |
| |
| U_BOOT_DRIVER(rockchip_udphy_u3_port) = { |
| .name = "rockchip_udphy_u3_port", |
| .id = UCLASS_PHY, |
| .ops = &rockchip_u3phy_ops, |
| }; |
| |
| U_BOOT_DRIVER(rockchip_udphy) = { |
| .name = "rockchip_udphy", |
| .id = UCLASS_PHY, |
| .of_match = rockchip_udphy_dt_match, |
| .probe = rockchip_udphy_probe, |
| .bind = rockchip_udphy_bind, |
| .priv_auto = sizeof(struct rockchip_udphy), |
| }; |