| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2021 Macronix International Co., Ltd. |
| * |
| * Authors: |
| * zhengxunli <zhengxunli@mxic.com.tw> |
| */ |
| |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <errno.h> |
| #include <asm/io.h> |
| #include <malloc.h> |
| #include <spi.h> |
| #include <spi-mem.h> |
| #include <linux/bug.h> |
| #include <linux/iopoll.h> |
| |
| #define HC_CFG 0x0 |
| #define HC_CFG_IF_CFG(x) ((x) << 27) |
| #define HC_CFG_DUAL_SLAVE BIT(31) |
| #define HC_CFG_INDIVIDUAL BIT(30) |
| #define HC_CFG_NIO(x) (((x) / 4) << 27) |
| #define HC_CFG_TYPE(s, t) ((t) << (23 + ((s) * 2))) |
| #define HC_CFG_TYPE_SPI_NOR 0 |
| #define HC_CFG_TYPE_SPI_NAND 1 |
| #define HC_CFG_TYPE_SPI_RAM 2 |
| #define HC_CFG_TYPE_RAW_NAND 3 |
| #define HC_CFG_SLV_ACT(x) ((x) << 21) |
| #define HC_CFG_CLK_PH_EN BIT(20) |
| #define HC_CFG_CLK_POL_INV BIT(19) |
| #define HC_CFG_BIG_ENDIAN BIT(18) |
| #define HC_CFG_DATA_PASS BIT(17) |
| #define HC_CFG_IDLE_SIO_LVL(x) ((x) << 16) |
| #define HC_CFG_MAN_START_EN BIT(3) |
| #define HC_CFG_MAN_START BIT(2) |
| #define HC_CFG_MAN_CS_EN BIT(1) |
| #define HC_CFG_MAN_CS_ASSERT BIT(0) |
| |
| #define INT_STS 0x4 |
| #define INT_STS_EN 0x8 |
| #define INT_SIG_EN 0xc |
| #define INT_STS_ALL GENMASK(31, 0) |
| #define INT_RDY_PIN BIT(26) |
| #define INT_RDY_SR BIT(25) |
| #define INT_LNR_SUSP BIT(24) |
| #define INT_ECC_ERR BIT(17) |
| #define INT_CRC_ERR BIT(16) |
| #define INT_LWR_DIS BIT(12) |
| #define INT_LRD_DIS BIT(11) |
| #define INT_SDMA_INT BIT(10) |
| #define INT_DMA_FINISH BIT(9) |
| #define INT_RX_NOT_FULL BIT(3) |
| #define INT_RX_NOT_EMPTY BIT(2) |
| #define INT_TX_NOT_FULL BIT(1) |
| #define INT_TX_EMPTY BIT(0) |
| |
| #define HC_EN 0x10 |
| #define HC_EN_BIT BIT(0) |
| |
| #define TXD(x) (0x14 + ((x) * 4)) |
| #define RXD 0x24 |
| |
| #define SS_CTRL(s) (0x30 + ((s) * 4)) |
| #define LRD_CFG 0x44 |
| #define LWR_CFG 0x80 |
| #define RWW_CFG 0x70 |
| #define OP_READ BIT(23) |
| #define OP_DUMMY_CYC(x) ((x) << 17) |
| #define OP_ADDR_BYTES(x) ((x) << 14) |
| #define OP_CMD_BYTES(x) (((x) - 1) << 13) |
| #define OP_OCTA_CRC_EN BIT(12) |
| #define OP_DQS_EN BIT(11) |
| #define OP_ENHC_EN BIT(10) |
| #define OP_PREAMBLE_EN BIT(9) |
| #define OP_DATA_DDR BIT(8) |
| #define OP_DATA_BUSW(x) ((x) << 6) |
| #define OP_ADDR_DDR BIT(5) |
| #define OP_ADDR_BUSW(x) ((x) << 3) |
| #define OP_CMD_DDR BIT(2) |
| #define OP_CMD_BUSW(x) (x) |
| #define OP_BUSW_1 0 |
| #define OP_BUSW_2 1 |
| #define OP_BUSW_4 2 |
| #define OP_BUSW_8 3 |
| |
| #define OCTA_CRC 0x38 |
| #define OCTA_CRC_IN_EN(s) BIT(3 + ((s) * 16)) |
| #define OCTA_CRC_CHUNK(s, x) ((fls((x) / 32)) << (1 + ((s) * 16))) |
| #define OCTA_CRC_OUT_EN(s) BIT(0 + ((s) * 16)) |
| |
| #define ONFI_DIN_CNT(s) (0x3c + (s)) |
| |
| #define LRD_CTRL 0x48 |
| #define RWW_CTRL 0x74 |
| #define LWR_CTRL 0x84 |
| #define LMODE_EN BIT(31) |
| #define LMODE_SLV_ACT(x) ((x) << 21) |
| #define LMODE_CMD1(x) ((x) << 8) |
| #define LMODE_CMD0(x) (x) |
| |
| #define LRD_ADDR 0x4c |
| #define LWR_ADDR 0x88 |
| #define LRD_RANGE 0x50 |
| #define LWR_RANGE 0x8c |
| |
| #define AXI_SLV_ADDR 0x54 |
| |
| #define DMAC_RD_CFG 0x58 |
| #define DMAC_WR_CFG 0x94 |
| #define DMAC_CFG_PERIPH_EN BIT(31) |
| #define DMAC_CFG_ALLFLUSH_EN BIT(30) |
| #define DMAC_CFG_LASTFLUSH_EN BIT(29) |
| #define DMAC_CFG_QE(x) (((x) + 1) << 16) |
| #define DMAC_CFG_BURST_LEN(x) (((x) + 1) << 12) |
| #define DMAC_CFG_BURST_SZ(x) ((x) << 8) |
| #define DMAC_CFG_DIR_READ BIT(1) |
| #define DMAC_CFG_START BIT(0) |
| |
| #define DMAC_RD_CNT 0x5c |
| #define DMAC_WR_CNT 0x98 |
| |
| #define SDMA_ADDR 0x60 |
| |
| #define DMAM_CFG 0x64 |
| #define DMAM_CFG_START BIT(31) |
| #define DMAM_CFG_CONT BIT(30) |
| #define DMAM_CFG_SDMA_GAP(x) (fls((x) / 8192) << 2) |
| #define DMAM_CFG_DIR_READ BIT(1) |
| #define DMAM_CFG_EN BIT(0) |
| |
| #define DMAM_CNT 0x68 |
| |
| #define LNR_TIMER_TH 0x6c |
| |
| #define RDM_CFG0 0x78 |
| #define RDM_CFG0_POLY(x) (x) |
| |
| #define RDM_CFG1 0x7c |
| #define RDM_CFG1_RDM_EN BIT(31) |
| #define RDM_CFG1_SEED(x) (x) |
| |
| #define LWR_SUSP_CTRL 0x90 |
| #define LWR_SUSP_CTRL_EN BIT(31) |
| |
| #define DMAS_CTRL 0x9c |
| #define DMAS_CTRL_EN BIT(31) |
| #define DMAS_CTRL_DIR_READ BIT(30) |
| |
| #define DATA_STROB 0xa0 |
| #define DATA_STROB_EDO_EN BIT(2) |
| #define DATA_STROB_INV_POL BIT(1) |
| #define DATA_STROB_DELAY_2CYC BIT(0) |
| |
| #define IDLY_CODE(x) (0xa4 + ((x) * 4)) |
| #define IDLY_CODE_VAL(x, v) ((v) << (((x) % 4) * 8)) |
| |
| #define GPIO 0xc4 |
| #define GPIO_PT(x) BIT(3 + ((x) * 16)) |
| #define GPIO_RESET(x) BIT(2 + ((x) * 16)) |
| #define GPIO_HOLDB(x) BIT(1 + ((x) * 16)) |
| #define GPIO_WPB(x) BIT((x) * 16) |
| |
| #define HC_VER 0xd0 |
| |
| #define HW_TEST(x) (0xe0 + ((x) * 4)) |
| |
| struct mxic_spi_priv { |
| struct clk *send_clk; |
| struct clk *send_dly_clk; |
| void __iomem *regs; |
| u32 cur_speed_hz; |
| }; |
| |
| static int mxic_spi_clk_enable(struct mxic_spi_priv *priv) |
| { |
| int ret; |
| |
| ret = clk_prepare_enable(priv->send_clk); |
| if (ret) |
| return ret; |
| |
| ret = clk_prepare_enable(priv->send_dly_clk); |
| if (ret) |
| goto err_send_dly_clk; |
| |
| return ret; |
| |
| err_send_dly_clk: |
| clk_disable_unprepare(priv->send_clk); |
| |
| return ret; |
| } |
| |
| static void mxic_spi_clk_disable(struct mxic_spi_priv *priv) |
| { |
| clk_disable_unprepare(priv->send_clk); |
| clk_disable_unprepare(priv->send_dly_clk); |
| } |
| |
| static void mxic_spi_set_input_delay_dqs(struct mxic_spi_priv *priv, |
| u8 idly_code) |
| { |
| writel(IDLY_CODE_VAL(0, idly_code) | |
| IDLY_CODE_VAL(1, idly_code) | |
| IDLY_CODE_VAL(2, idly_code) | |
| IDLY_CODE_VAL(3, idly_code), |
| priv->regs + IDLY_CODE(0)); |
| writel(IDLY_CODE_VAL(4, idly_code) | |
| IDLY_CODE_VAL(5, idly_code) | |
| IDLY_CODE_VAL(6, idly_code) | |
| IDLY_CODE_VAL(7, idly_code), |
| priv->regs + IDLY_CODE(1)); |
| } |
| |
| static int mxic_spi_clk_setup(struct mxic_spi_priv *priv, uint freq) |
| { |
| int ret; |
| |
| ret = clk_set_rate(priv->send_clk, freq); |
| if (ret) |
| return ret; |
| |
| ret = clk_set_rate(priv->send_dly_clk, freq); |
| if (ret) |
| return ret; |
| |
| /* |
| * A constant delay range from 0x0 ~ 0x1F for input delay, |
| * the unit is 78 ps, the max input delay is 2.418 ns. |
| */ |
| mxic_spi_set_input_delay_dqs(priv, 0xf); |
| |
| return 0; |
| } |
| |
| static int mxic_spi_set_speed(struct udevice *bus, uint freq) |
| { |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| int ret; |
| |
| if (priv->cur_speed_hz == freq) |
| return 0; |
| |
| mxic_spi_clk_disable(priv); |
| ret = mxic_spi_clk_setup(priv, freq); |
| if (ret) |
| return ret; |
| |
| ret = mxic_spi_clk_enable(priv); |
| if (ret) |
| return ret; |
| |
| priv->cur_speed_hz = freq; |
| |
| return 0; |
| } |
| |
| static int mxic_spi_set_mode(struct udevice *bus, uint mode) |
| { |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| u32 hc_config = 0; |
| |
| if (mode & SPI_CPHA) |
| hc_config |= HC_CFG_CLK_PH_EN; |
| if (mode & SPI_CPOL) |
| hc_config |= HC_CFG_CLK_POL_INV; |
| |
| writel(hc_config, priv->regs + HC_CFG); |
| |
| return 0; |
| } |
| |
| static void mxic_spi_hw_init(struct mxic_spi_priv *priv) |
| { |
| writel(0, priv->regs + DATA_STROB); |
| writel(INT_STS_ALL, priv->regs + INT_STS_EN); |
| writel(0, priv->regs + HC_EN); |
| writel(0, priv->regs + LRD_CFG); |
| writel(0, priv->regs + LRD_CTRL); |
| writel(HC_CFG_NIO(1) | HC_CFG_TYPE(0, HC_CFG_TYPE_SPI_NOR) | |
| HC_CFG_SLV_ACT(0) | HC_CFG_MAN_CS_EN | HC_CFG_IDLE_SIO_LVL(1), |
| priv->regs + HC_CFG); |
| } |
| |
| static int mxic_spi_data_xfer(struct mxic_spi_priv *priv, const void *txbuf, |
| void *rxbuf, unsigned int len) |
| { |
| unsigned int pos = 0; |
| |
| while (pos < len) { |
| unsigned int nbytes = len - pos; |
| u32 data = 0xffffffff; |
| u32 sts; |
| int ret; |
| |
| if (nbytes > 4) |
| nbytes = 4; |
| |
| if (txbuf) |
| memcpy(&data, txbuf + pos, nbytes); |
| |
| ret = readl_poll_timeout(priv->regs + INT_STS, sts, |
| sts & INT_TX_EMPTY, 1000000); |
| if (ret) |
| return ret; |
| |
| writel(data, priv->regs + TXD(nbytes % 4)); |
| |
| if (rxbuf) { |
| ret = readl_poll_timeout(priv->regs + INT_STS, sts, |
| sts & INT_TX_EMPTY, |
| 1000000); |
| if (ret) |
| return ret; |
| |
| ret = readl_poll_timeout(priv->regs + INT_STS, sts, |
| sts & INT_RX_NOT_EMPTY, |
| 1000000); |
| if (ret) |
| return ret; |
| |
| data = readl(priv->regs + RXD); |
| data >>= (8 * (4 - nbytes)); |
| memcpy(rxbuf + pos, &data, nbytes); |
| WARN_ON(readl(priv->regs + INT_STS) & INT_RX_NOT_EMPTY); |
| } else { |
| readl(priv->regs + RXD); |
| } |
| WARN_ON(readl(priv->regs + INT_STS) & INT_RX_NOT_EMPTY); |
| |
| pos += nbytes; |
| } |
| |
| return 0; |
| } |
| |
| static bool mxic_spi_mem_supports_op(struct spi_slave *slave, |
| const struct spi_mem_op *op) |
| { |
| if (op->data.buswidth > 8 || op->addr.buswidth > 8 || |
| op->dummy.buswidth > 8 || op->cmd.buswidth > 8) |
| return false; |
| |
| if (op->addr.nbytes > 7) |
| return false; |
| |
| return spi_mem_default_supports_op(slave, op); |
| } |
| |
| static int mxic_spi_mem_exec_op(struct spi_slave *slave, |
| const struct spi_mem_op *op) |
| { |
| struct dm_spi_slave_plat *slave_plat = dev_get_parent_plat(slave->dev); |
| struct udevice *bus = slave->dev->parent; |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| int nio = 1, i, ret; |
| u32 ss_ctrl; |
| u8 addr[8], dummy_bytes = 0; |
| |
| if (slave->mode & (SPI_TX_OCTAL | SPI_RX_OCTAL)) |
| nio = 8; |
| else if (slave->mode & (SPI_TX_QUAD | SPI_RX_QUAD)) |
| nio = 4; |
| else if (slave->mode & (SPI_TX_DUAL | SPI_RX_DUAL)) |
| nio = 2; |
| |
| writel(HC_CFG_NIO(nio) | |
| HC_CFG_TYPE(slave_plat->cs, HC_CFG_TYPE_SPI_NOR) | |
| HC_CFG_SLV_ACT(slave_plat->cs) | HC_CFG_IDLE_SIO_LVL(1) | |
| HC_CFG_MAN_CS_EN, |
| priv->regs + HC_CFG); |
| writel(HC_EN_BIT, priv->regs + HC_EN); |
| |
| ss_ctrl = OP_CMD_BYTES(1) | OP_CMD_BUSW(fls(op->cmd.buswidth) - 1); |
| |
| if (op->addr.nbytes) |
| ss_ctrl |= OP_ADDR_BYTES(op->addr.nbytes) | |
| OP_ADDR_BUSW(fls(op->addr.buswidth) - 1); |
| |
| /* |
| * Since the SPI MXIC dummy buswidth is aligned with the data buswidth, |
| * the dummy byte needs to be recalculated to send out the correct |
| * dummy cycle. |
| */ |
| if (op->dummy.nbytes) { |
| dummy_bytes = op->dummy.nbytes / |
| op->addr.buswidth * |
| op->data.buswidth; |
| ss_ctrl |= OP_DUMMY_CYC(dummy_bytes); |
| } |
| |
| if (op->data.nbytes) { |
| ss_ctrl |= OP_DATA_BUSW(fls(op->data.buswidth) - 1); |
| if (op->data.dir == SPI_MEM_DATA_IN) |
| ss_ctrl |= OP_READ; |
| } |
| |
| writel(ss_ctrl, priv->regs + SS_CTRL(slave_plat->cs)); |
| |
| writel(readl(priv->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT, |
| priv->regs + HC_CFG); |
| |
| ret = mxic_spi_data_xfer(priv, &op->cmd.opcode, NULL, 1); |
| if (ret) |
| goto out; |
| |
| for (i = 0; i < op->addr.nbytes; i++) |
| addr[i] = op->addr.val >> (8 * (op->addr.nbytes - i - 1)); |
| |
| ret = mxic_spi_data_xfer(priv, addr, NULL, op->addr.nbytes); |
| if (ret) |
| goto out; |
| |
| ret = mxic_spi_data_xfer(priv, NULL, NULL, dummy_bytes); |
| if (ret) |
| goto out; |
| |
| ret = mxic_spi_data_xfer(priv, |
| op->data.dir == SPI_MEM_DATA_OUT ? |
| op->data.buf.out : NULL, |
| op->data.dir == SPI_MEM_DATA_IN ? |
| op->data.buf.in : NULL, |
| op->data.nbytes); |
| |
| out: |
| writel(readl(priv->regs + HC_CFG) & ~HC_CFG_MAN_CS_ASSERT, |
| priv->regs + HC_CFG); |
| writel(0, priv->regs + HC_EN); |
| |
| return ret; |
| } |
| |
| static const struct spi_controller_mem_ops mxic_spi_mem_ops = { |
| .supports_op = mxic_spi_mem_supports_op, |
| .exec_op = mxic_spi_mem_exec_op, |
| }; |
| |
| static int mxic_spi_claim_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev_get_parent(dev); |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| |
| writel(readl(priv->regs + HC_CFG) | HC_CFG_MAN_CS_EN, |
| priv->regs + HC_CFG); |
| writel(HC_EN_BIT, priv->regs + HC_EN); |
| writel(readl(priv->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT, |
| priv->regs + HC_CFG); |
| |
| return 0; |
| } |
| |
| static int mxic_spi_release_bus(struct udevice *dev) |
| { |
| struct udevice *bus = dev_get_parent(dev); |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| |
| writel(readl(priv->regs + HC_CFG) & ~HC_CFG_MAN_CS_ASSERT, |
| priv->regs + HC_CFG); |
| writel(0, priv->regs + HC_EN); |
| |
| return 0; |
| } |
| |
| static int mxic_spi_xfer(struct udevice *dev, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| struct udevice *bus = dev_get_parent(dev); |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| struct spi_slave *slave = dev_get_parent_priv(dev); |
| unsigned int busw = OP_BUSW_1; |
| unsigned int len = bitlen / 8; |
| int ret; |
| |
| if (dout && din) { |
| if (((slave->mode & SPI_TX_QUAD) && |
| !(slave->mode & SPI_RX_QUAD)) || |
| ((slave->mode & SPI_TX_DUAL) && |
| !(slave->mode & SPI_RX_DUAL))) |
| return -ENOTSUPP; |
| } |
| |
| if (din) { |
| if (slave->mode & SPI_TX_QUAD) |
| busw = OP_BUSW_4; |
| else if (slave->mode & SPI_TX_DUAL) |
| busw = OP_BUSW_2; |
| } else if (dout) { |
| if (slave->mode & SPI_RX_QUAD) |
| busw = OP_BUSW_4; |
| else if (slave->mode & SPI_RX_DUAL) |
| busw = OP_BUSW_2; |
| } |
| |
| writel(OP_CMD_BYTES(1) | OP_CMD_BUSW(busw) | |
| OP_DATA_BUSW(busw) | (din ? OP_READ : 0), |
| priv->regs + SS_CTRL(0)); |
| |
| ret = mxic_spi_data_xfer(priv, dout, din, len); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int mxic_spi_probe(struct udevice *bus) |
| { |
| struct mxic_spi_priv *priv = dev_get_priv(bus); |
| |
| priv->regs = dev_read_addr_ptr(bus); |
| |
| priv->send_clk = devm_clk_get(bus, "send_clk"); |
| if (IS_ERR(priv->send_clk)) |
| return PTR_ERR(priv->send_clk); |
| |
| priv->send_dly_clk = devm_clk_get(bus, "send_dly_clk"); |
| if (IS_ERR(priv->send_dly_clk)) |
| return PTR_ERR(priv->send_dly_clk); |
| |
| mxic_spi_hw_init(priv); |
| |
| return 0; |
| } |
| |
| static const struct dm_spi_ops mxic_spi_ops = { |
| .claim_bus = mxic_spi_claim_bus, |
| .release_bus = mxic_spi_release_bus, |
| .xfer = mxic_spi_xfer, |
| .set_speed = mxic_spi_set_speed, |
| .set_mode = mxic_spi_set_mode, |
| .mem_ops = &mxic_spi_mem_ops, |
| }; |
| |
| static const struct udevice_id mxic_spi_ids[] = { |
| { .compatible = "mxicy,mx25f0a-spi", }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(mxic_spi) = { |
| .name = "mxic_spi", |
| .id = UCLASS_SPI, |
| .of_match = mxic_spi_ids, |
| .ops = &mxic_spi_ops, |
| .priv_auto = sizeof(struct mxic_spi_priv), |
| .probe = mxic_spi_probe, |
| }; |